commit 82fbd6a3e2 upstream.
Every time DM_VERITY_FEC_{MAX,MIN}_RSN are used, they are subtracted
from DM_VERITY_FEC_RSM to get the bounds on the number of roots.
Therefore, replace these with {MIN,MAX}_ROOTS constants which are more
directly useful. (Note the inversion, where MAX_RSN maps to MIN_ROOTS
and MIN_RSN maps to MAX_ROOTS.) No functional change.
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 430a05cb92 upstream.
fec_decode_bufs() assumes that the parity bytes of the first RS codeword
it decodes are never split across parity blocks.
This assumption is false. Consider v->fec->block_size == 4096 &&
v->fec->roots == 17 && fio->nbufs == 1, for example. In that case, each
call to fec_decode_bufs() consumes v->fec->roots * (fio->nbufs <<
DM_VERITY_FEC_BUF_RS_BITS) = 272 parity bytes.
Considering that the parity data for each message block starts on a
block boundary, the byte alignment in the parity data will iterate
through 272*i mod 4096 until the 3 parity blocks have been consumed. On
the 16th call (i=15), the alignment will be 4080 bytes into the first
block. Only 16 bytes remain in that block, but 17 parity bytes will be
needed. The code reads out-of-bounds from the parity block buffer.
Fortunately this doesn't normally happen, since it can occur only for
certain non-default values of fec_roots *and* when the maximum number of
buffers couldn't be allocated due to low memory. For example with
block_size=4096 only the following cases are affected:
fec_roots=17: nbufs in [1, 3, 5, 15]
fec_roots=19: nbufs in [1, 229]
fec_roots=21: nbufs in [1, 3, 5, 13, 15, 39, 65, 195]
fec_roots=23: nbufs in [1, 89]
Regardless, fix it by refactoring how the parity blocks are read.
Fixes: 6df90c02ba ("dm-verity FEC: Fix RS FEC repair for roots unaligned to block size (take 2)")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a7fca324d7 upstream.
At most 25 entries in dm_verity_fec_io::erasures are used: the maximum
number of FEC roots plus one. Therefore, set the array size
accordingly. This reduces the size of dm_verity_fec_io by 912 bytes.
Note: a later commit introduces a constant DM_VERITY_FEC_MAX_ROOTS,
which allows the size to be more clearly expressed as
DM_VERITY_FEC_MAX_ROOTS + 1. This commit just fixes the size first.
Fixes: a739ff3f54 ("dm verity: add support for forward error correction")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10f86a2a5c ]
When a BPF sock_ops program accesses ctx fields with dst_reg == src_reg,
the SOCK_OPS_GET_SK() and SOCK_OPS_GET_FIELD() macros fail to zero the
destination register in the !fullsock / !locked_tcp_sock path.
Both macros borrow a temporary register to check is_fullsock /
is_locked_tcp_sock when dst_reg == src_reg, because dst_reg holds the
ctx pointer. When the check is false (e.g., TCP_NEW_SYN_RECV state with
a request_sock), dst_reg should be zeroed but is not, leaving the stale
ctx pointer:
- SOCK_OPS_GET_SK: dst_reg retains the ctx pointer, passes NULL checks
as PTR_TO_SOCKET_OR_NULL, and can be used as a bogus socket pointer,
leading to stack-out-of-bounds access in helpers like
bpf_skc_to_tcp6_sock().
- SOCK_OPS_GET_FIELD: dst_reg retains the ctx pointer which the
verifier believes is a SCALAR_VALUE, leaking a kernel pointer.
Fix both macros by:
- Changing JMP_A(1) to JMP_A(2) in the fullsock path to skip the
added instruction.
- Adding BPF_MOV64_IMM(si->dst_reg, 0) after the temp register
restore in the !fullsock path, placed after the restore because
dst_reg == src_reg means we need src_reg intact to read ctx->temp.
Fixes: fd09af0107 ("bpf: sock_ops ctx access may stomp registers in corner case")
Fixes: 84f44df664 ("bpf: sock_ops sk access may stomp registers when dst_reg = src_reg")
Reported-by: Quan Sun <2022090917019@std.uestc.edu.cn>
Reported-by: Yinhao Hu <dddddd@hust.edu.cn>
Reported-by: Kaiyan Mei <M202472210@hust.edu.cn>
Reported-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com>
Closes: https://lore.kernel.org/bpf/6fe1243e-149b-4d3b-99c7-fcc9e2f75787@std.uestc.edu.cn/T/#u
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20260407022720.162151-2-jiayuan.chen@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Jay Wang <wanjay@amazon.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 220f22e1d6 upstream.
SMU13 reports SocketPowerLimitAc/Dc as the default power limit, but
MsgLimits.Power may carry a different firmware bound for the same PPT
throttler. Using only the socket limit for both min and max can therefore
expose an incorrect power range.
Keep the socket limit as the default, but derive the range from both values:
use the lower value for the min base and the higher value for the max base
before applying OD percentages. Keep the current limit query independent
from the cap calculation.
Fixes: 1eaf26db95 ("drm/amd/pm: fix smu13 power limit default/cap calculation")
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5419
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f45bbf0f62)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea772a440d upstream.
amdgpu_pci_remove() calls drm_dev_unplug() before invoking the driver
fini routines. This causes drm_dev_enter() in amdgpu_ttm_fini() to
always return false, so iounmap(aper_base_kaddr) never runs on normal
driver unload, leaving an orphaned entry in the x86 PAT interval tree.
On connected_to_cpu hardware, the aperture is mapped write-back (WB) via
ioremap_cache(). On reload, IP discovery calls memremap(..., MEMREMAP_WC)
over the same range. The WC vs WB conflict causes:
ioremap error for 0x..., requested 0x1, got 0x0
amdgpu: discovery failed: -2
Fix by switching to devres-managed mappings so cleanup is guaranteed
regardless of drm_dev_enter() state:
- connected_to_cpu path: devm_memremap(MEMREMAP_WB). For
IORESOURCE_SYSTEM_RAM ranges this takes the try_ram_remap() shortcut,
returning __va(offset) from the existing kernel direct map. No new
ioremap VA or PAT entry is created, so there is nothing to orphan.
- dGPU path: devm_ioremap_wc() registers iounmap() as a devres action,
guaranteeing cleanup at device_del() time.
Also remove iounmap(aper_base_kaddr) from amdgpu_device_unmap_mmio()
since the mapping is now devres-owned.
v2: Remove redundant x86_64 guard (Lijo)
Fixes: 9d0af8b4de ("drm/amdgpu: pre-map device buffer as cached for A+A config")
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d871e99879)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 020da7c5aa upstream.
When ACP soft reset poll times out, original code returns early without cleanup,
leaking MFD child devices, genpd links and all ACP heap allocations.
Replace direct early return with goto out to force run all cleanup logic
regardless of reset success, preserve timeout error code for caller.
Signed-off-by: Ce Sun <cesun102@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 98073e4328)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c01c811be upstream.
When width or height is less than 16, width_in_mb or height_in_mb
becomes 0, leading to fs_in_mb being 0. This causes a division by
zero when calculating num_dpb_buffer in H264 and H264 Perf decode
paths.
Add validation to reject frames with width < 16 or height < 16
before performing any calculations that depend on these values.
V2: Format change - move up all vaiable definitions.
V3: Use warn_once to avoid spam.
Signed-off-by: Boyuan Zhang <boyuan.zhang@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 3e41d26c70)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6130598759 upstream.
A hotplug or link-loss event can tear down the MST topology
(setting mgr->mst_state = false and mgr->mst_primary = NULL) concurrently
with a caller invoking drm_dp_mst_topology_queue_probe(). Since the check
is already performed under mgr->lock, the condition is not a programming
error but a valid race -- the topology was valid when the caller decided
to call this function, but was torn down before the lock was acquired.
Replace the drm_WARN_ON() with a graceful early return. This eliminates
spurious kernel warnings and the resulting compositor crashes observed
when connecting/disconnecting DP MST monitors, while keeping the correct
behavior of doing nothing when MST is not active. A drm_dbg_mst() trace
is added so the skipped probe remains observable under MST debug logging.
The existing WARN_ON(mgr->mst_primary) in drm_dp_mst_topology_mgr_set_mst()
already catches the case where the topology is initialized twice, so no
diagnostic coverage is lost.
Fixes: dbaeef363e ("drm/dp_mst: Add a helper to queue a topology probe")
Cc: Imre Deak <imre.deak@intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Jonas Emilsson <jonas.emilsson@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/all/20260503034533.1023686-1-jonas.emilsson@gmail.com
Acked-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260622140532.526722-1-luciano.coelho@intel.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 186bfdc4e2 upstream.
Fix a security vulnerability where malicious VCE command streams
with oversized dimensions (e.g. 65536×65536) cause 32-bit integer
overflow, wrapping the calculated buffer size to 0. This bypasses
validation and allows GPU firmware to perform out-of-bound memory
access.
The fix uses 64-bit arithmetic to detect overflow and rejects
invalid dimensions before they reach the hardware.
V2: remove redundant check
V3: modify max height value
V4: remove size64
Signed-off-by: Boyuan Zhang <boyuan.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit cbe408dba5)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aff079bdce upstream.
For SOC24 ASICs (RDNA4 / Navi 4x dGPUs) re-enabling PM features fails if an
S3 suspend got aborted, the same issue already handled for SOC21 and SOC15:
commit df3c7dc5c5 ("drm/amdgpu: Reset dGPU if suspend got aborted")
commit 38e8ca3e4b ("amdgpu/soc15: enable asic reset for dGPU in case of suspend abort")
The aborted resume fails with:
amdgpu: SMU: No response msg_reg: 6 resp_reg: 0
amdgpu: Failed to enable requested dpm features!
amdgpu: resume of IP block <smu> failed -62
Apply the same workaround for soc24: detect the aborted-suspend state at
resume via the sign-of-life register and reset the device before re-init.
This is a workaround till a proper solution is finalized.
Fixes: 98b912c50e ("drm/amdgpu: Add soc24 common ip block (v2)")
Signed-off-by: Jakob Linke <jakob@linke.cx>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit fed5bdbfe1)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efcedeecec upstream.
jpeg_v5_0_1_is_idle() initializes ret to false and then accumulates ring
idle status using &=. Since false & condition always remains false, the
function can never report the JPEG block as idle.
Initialize ret to true so the function returns true only when all JPEG
rings report RB_JOB_DONE.
Signed-off-by: Boyuan Zhang <boyuan.zhang@amd.com>
Reviewed-by: David (Ming Qiang) Wu <David.Wu3@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 680adf5fae)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c44af3810f upstream.
jpeg_v4_0_3_is_idle() initializes ret to false and then accumulates ring
idle status using &=. Since false & condition always remains false, the
function can never report the JPEG block as idle.
Initialize ret to true so the function returns true only when all JPEG
rings report RB_JOB_DONE.
Signed-off-by: Boyuan Zhang <boyuan.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit e9df8e9d04)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 238baca26a upstream.
amdgpu_pm_info displayed power sensor readings with the wrong fractional unit.
It treated the low byte of the raw sensor value as the decimal part of watts,
while that field represents milliwatts in the decoded value. As a result,
debugfs could report misleading SoC power when the remainder was not already
a two-digit centiwatt value.
Example with query = 0x00000354:
raw field value
---------------------
query >> 8 3 W
query & 0xff 84 mW
decoded power 3084 mW
output value
---------------------
before 3.84 W
after 3.08 W
Fixes: f0b8f65b48 ("drm/amd/amdgpu: fix the GPU power print error in pm info")
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 01992b121f)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b37415618 upstream.
The s32g_wdt driver uses two incorrect constants in the options field
of its watchdog_info struct. This bit mask should contain WDIOF_*
constants, but the driver uses two WDIOC_* ioctl constants (in addition
to correct WDIOF_* constants). This causes many incorrect bits to be
set in the bit mask. The functionality indicated by these ioctl
constants is supported by all drivers using the watchdog framework, so
this patch simply removes them.
Fixes: bd3f54ec55 ("watchdog: Add the Watchdog Timer for the NXP S32 platform")
Cc: stable@vger.kernel.org # 6.18+
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260505024409.60301-1-enelsonmoore@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcd9b46596 upstream.
When replacing the source list of an MDB remote entry, all existing
sources are first marked for deletion and vxlan_mdb_remote_srcs_add()
is then called to add the new source list. Sources present in the new
list have their deletion mark cleared, and any sources left marked
afterwards are removed.
If vxlan_mdb_remote_srcs_add() fails partway through, its error path
deletes all entries on the remote's source list. That rollback is only
correct for its other caller, vxlan_mdb_remote_add(), where the remote
was just allocated and the list contains solely entries added during
the call. On the replace path the list also holds pre-existing sources,
so a failed replace tears them down together with their (S, G)
forwarding entries instead of leaving the entry unchanged.
This is reachable from an existing (*, G) remote. An EXCLUDE filter
that loses sources starts forwarding traffic that should be blocked,
while an INCLUDE filter that loses sources drops traffic that should be
forwarded.
Mark entries created during the current pass with a new
VXLAN_SGRP_F_NEW flag. On failure, delete only those entries and clear
the deletion mark on the pre-existing ones, so a failed replace leaves
the source list untouched. Retain the flag until the whole operation
succeeds and then clear it. Also stop vxlan_mdb_remote_src_add() from
deleting a pre-existing entry it only looked up when adding that
entry's forwarding entry fails.
Fixes: a3a48de5ea ("vxlan: mdb: Add MDB control path support")
Cc: stable@vger.kernel.org
Signed-off-by: James Raphael Tiovalen <jamestiotio@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260720160428.249356-1-jamestiotio@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a12c05aef upstream.
When many small packets accumulate in the receive queue, the skb overhead
can exceed buf_alloc even while the payload is within bounds. This causes
virtio_transport_inc_rx_pkt() to reject packets, leading to connection
resets during large transfers under backpressure.
The issue was reported by Brien, who has a reproducer, but it is also
easily reproducible with iperf-vsock [1] using a small packet size:
iperf3 --vsock -c $CID -l 129
which fails immediately without this patch but with commit 059b7dbd20
("vsock/virtio: fix potential unbounded skb queue").
Inspired by TCP's tcp_collapse() which solves a similar problem, add
virtio_transport_collapse_rx_queue() that walks the receive queue and
re-copies data into compact linear skbs to reduce the overhead.
The collapse is triggered proactively from when the number of skb queued
is close to exceeding the overhead budget.
A pre-scan counts the eligible bytes to size each allocation precisely,
avoiding waste for isolated small packets. Partially consumed skbs are
kept as-is to preserve buf_used/fwd_cnt accounting, EOM-marked skbs to
maintain SEQPACKET message boundaries, and skbs already larger than the
collapse target because they already have a good data-to-overhead ratio.
Walking a large queue may take a significant amount of time and cache
misses, causing traffic burstiness. To limit this, the collapse stops
once enough room is freed for this packet and the next one, but may
opportunistically free more to fill each collapsed skb to capacity.
[1] https://github.com/stefano-garzarella/iperf-vsock
Fixes: 059b7dbd20 ("vsock/virtio: fix potential unbounded skb queue")
Cc: stable@vger.kernel.org
Reported-by: Brien Oberstein <brienpub@gmail.com>
Closes: https://lore.kernel.org/netdev/618701dd023e$063de350$12b9a9f0$@gmail.com/
Tested-by: Brien Oberstein <brienpub@gmail.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Bobby Eshleman <bobbyeshleman@meta.com>
Link: https://patch.msgid.link/20260708102904.50732-2-sgarzare@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba0533fc16 upstream.
When tipc_sk_create() fails to insert the new socket (tipc_sk_insert()
returns non-zero), its error path frees the sk with sk_free() but leaves
sock->sk pointing at the freed object:
if (tipc_sk_insert(tsk)) {
sk_free(sk);
pr_warn("Socket create failed; port number exhausted\n");
return -EINVAL;
}
This is harmless for plain socket(): the syscall layer clears sock->ops
before releasing, so tipc_release() is never called. It is not harmless
on the accept() path. tipc_accept() creates the pre-allocated child
socket with tipc_sk_create(net, new_sock, 0, kern); on failure it leaves
new_sock->sk dangling and new_sock->ops non-NULL, and do_accept() then
fput()s the new file, so __sock_release() -> tipc_release() runs
lock_sock(new_sock->sk) on the freed sk -- a use-after-free write of the
sk_lock spinlock.
tipc_release() already guards this exact "failed accept() releases a
pre-allocated child" case with "if (sk == NULL) return 0;", but the
guard is bypassed because tipc_sk_create() left sock->sk non-NULL
(dangling) rather than NULL.
Clear sock->sk on the failed-insert path so the existing tipc_release()
NULL check fires and the use-after-free is avoided.
The tipc_sk_insert() failure is reached when the per-netns socket
rhashtable hits its max_size (tsk_rht_params.max_size = 1048576, ~2M
elements) -- i.e. once a netns holds ~2M TIPC sockets every insert
returns -E2BIG.
BUG: KASAN: slab-use-after-free in lock_sock_nested (net/core/sock.c:3839)
Write of size 8 at addr ffff8880047cdc38 by task init/1
lock_sock_nested (net/core/sock.c:3839)
tipc_release (net/tipc/socket.c:638)
__sock_release (net/socket.c:710)
sock_close (net/socket.c:1501)
__fput (fs/file_table.c:512)
Allocated by task 1:
sk_alloc (net/core/sock.c:2308)
tipc_sk_create (net/tipc/socket.c:487)
tipc_accept (net/tipc/socket.c:2744)
do_accept (net/socket.c:2034)
Freed by task 1:
__sk_destruct (net/core/sock.c:2391)
tipc_sk_create (net/tipc/socket.c:504)
tipc_accept (net/tipc/socket.c:2744)
do_accept (net/socket.c:2034)
Fixes: 00aff3590f ("net: tipc: fix possible refcount leak in tipc_sk_create()")
Cc: stable@vger.kernel.org
Reviewed-by: Tung Nguyen <tung.quang.nguyen@est.tech>
Reviewed-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Daehyeon Ko <4ncienth@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260714131939.1255974-1-4ncienth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a28c4fcbf7 upstream.
The SYN-RECEIVED request-socket path in tcp_check_req() accepts an
in-window RST without requiring SEG.SEQ to exactly match RCV.NXT. A
non-exact RST therefore removes the request instead of eliciting a
challenge ACK.
RFC 9293 section 3.10.7.4 applies the RFC 5961 reset check in
SYN-RECEIVED: an exact RST resets the connection, while a non-exact
in-window RST must trigger a challenge ACK and be dropped.
Apply that check before the ACK-field validation, following the RFC
sequence-number, RST, then ACK processing order. Factor the per-netns
challenge ACK quota out of tcp_send_challenge_ack() so request sockets
can share it. Use the request socket's send_ack() callback and its own
out-of-window ACK timestamp to send and rate-limit the response.
Reported-by: Yuxiang Yang <yangyx22@mails.tsinghua.edu.cn>
Reported-by: Yizhou Zhao <zhaoyz24@mails.tsinghua.edu.cn>
Reported-by: Ao Wang <wangao@seu.edu.cn>
Reported-by: Xuewei Feng <fengxw06@126.com>
Reported-by: Qi Li <qli01@tsinghua.edu.cn>
Reported-by: Ke Xu <xuke@tsinghua.edu.cn>
Fixes: 282f23c6ee ("tcp: implement RFC 5961 3.2")
Cc: stable@vger.kernel.org
Signed-off-by: Yuxiang Yang <yangyx22@mails.tsinghua.edu.cn>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260717081443.809393-2-yangyx22@mails.tsinghua.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1a9d3cc11 upstream.
tcp_v4_send_ack() and tcp_v6_send_response() construct standalone TCP
responses with TCP-AO options. The option length carries the actual MAC
length, but the TCP header length includes the option rounded up to a
four-byte boundary.
tcp_ao_hash_hdr() writes the MAC only. Thus, when the MAC length is not
four-byte aligned, the one to three bytes after the MAC are left
uninitialized and may be transmitted. For the normal TCP-AO hashing
mode, those bytes also have to be initialized before computing the MAC.
Initialize only the alignment padding in the TCP-AO branches, before
hashing the header. Use TCPOPT_NOP, as in the normal TCP-AO output path.
This avoids adding work to non-AO TCP responses while preserving a valid
authenticated header.
Fixes: decde2586b ("net/tcp: Add TCP-AO sign to twsk")
Fixes: da7dfaa6d6 ("net/tcp: Consistently align TCP-AO option in the header")
Cc: stable@vger.kernel.org
Reported-by: Yizhou Zhao <zhaoyz24@mails.tsinghua.edu.cn>
Reported-by: Yuxiang Yang <yangyx22@mails.tsinghua.edu.cn>
Reported-by: Ao Wang <wangao@seu.edu.cn>
Reported-by: Xuewei Feng <fengxw06@126.com>
Reported-by: Qi Li <qli01@tsinghua.edu.cn>
Reported-by: Ke Xu <xuke@tsinghua.edu.cn>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yizhou Zhao <zhaoyz24@mails.tsinghua.edu.cn>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260713105631.8616-1-zhaoyz24@mails.tsinghua.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c50efa1fa upstream.
The hardware performs packet parsing before packet transmission.
Parsing incomplete IPv4, IPv6, TCP, or UDP headers may trigger a TX
hang because the hardware parser expects additional protocol header
data that is not present in the packet.
The hardware performs additional PTP parsing on UDP packets identified
by destination ports 319/320 at the expected UDP destination port
offset.
If such a packet has transport data smaller than RTASE_MIN_PAD_LEN,
the hardware parser expects additional packet data and may trigger a
TX hang.
To avoid these hardware issues, the driver applies the following
workarounds.
Drop malformed packets that may trigger this hardware issue before
transmission.
For IPv4 non-initial fragments, the hardware does not check the
fragment offset before parsing the expected transport header location.
As a result, these packets are still subject to transport header
parsing even though they do not contain a transport header. If the
transport data is shorter than the minimum transport header required
by the hardware parser, pad the transport data to the minimum
transport header length required by the hardware parser. Packets that
also match the hardware PTP parsing conditions continue to follow the
corresponding workaround.
For IPv6 fragmented packets, neither of the above hardware issues
occurs because the hardware only continues packet parsing when the
IPv6 Base Header Next Header field directly indicates UDP. Packets
carrying a Fragment Header do not continue through the subsequent
packet parsing stages.
For packets identified for hardware PTP parsing, pad the transport
data so it reaches RTASE_MIN_PAD_LEN before transmission.
Fixes: d6e882b89f ("rtase: Implement .ndo_start_xmit function")
Cc: stable@vger.kernel.org
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260709103456.83789-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9c238f6fe upstream.
pppoe_sendmsg() saves a pointer to the PPPoE header before calling
dev_hard_header(). Device header callbacks are allowed to reallocate the
skb head, invalidating pointers into it.
This can happen when a send is blocked in copy_from_user() while the first
non-Ethernet port is added to an empty team device. The team's delegated
GRE header callback then expands the skb head. PPPoE subsequently writes
six bytes through the stale pointer into the freed head.
Reload the PPPoE header through the skb's network-header offset after
device header creation. pskb_expand_head() updates that offset when it
relocates the head.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Asim Viladi Oglu Manizada <manizada@pm.me>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260722093814.3017176-1-manizada@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4710ae2e7 upstream.
ovpn_peer_keepalive_send() passes its peer reference to
ovpn_xmit_special(), which ultimately drops it. The keepalive scheduler
currently queues the work first and takes the reference only after
schedule_work() reports that the work was queued.
Once schedule_work() queues the item, another CPU may run the worker
before the caller gets to ovpn_peer_hold(). In that case the worker can
consume a reference that was not acquired for it, corrupting the peer
lifetime accounting.
Take the peer reference before queueing the work and drop it again when
the work was already pending.
Fixes: 3ecfd9349f ("ovpn: implement keepalive mechanism")
Cc: stable@vger.kernel.org
Signed-off-by: Shuvam Pandey <shuvampandey1@gmail.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Antonio Quartulli <antonio@openvpn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63bbe18fc0 upstream.
When either the TCP RX or TX error path calls ovpn_peer_hold() followed
by schedule_work(&peer->tcp.defer_del_work), and the work item is already
pending from the other path, schedule_work() returns false and the work
runs only once. Since ovpn_tcp_peer_del_work() calls ovpn_peer_put()
exactly once, the extra reference taken by the losing path is never
dropped, leaking the peer object.
The race window:
CPU0 (strparser/RX error): CPU1 (tcp_tx_work/TX error):
ovpn_peer_hold() <- refcnt+1 ovpn_peer_hold() <- refcnt+2
schedule_work() <- queued schedule_work() <- NO-OP
(work already pending)
ovpn_tcp_peer_del_work runs:
ovpn_peer_del()
ovpn_peer_put() <- refcnt+1
<- peer never freed
Fix by checking the return value of schedule_work() in both paths and
calling ovpn_peer_put() to drop the extra reference if the work was
already pending. ovpn_peer_hold() is kept unconditional in the TX path
as it cannot fail at that point.
Fixes: a6a5e87b3e ("ovpn: avoid sleep in atomic context in TCP RX error path")
Cc: stable@vger.kernel.org
Signed-off-by: Pavitra Jha <jhapavitra98@gmail.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Antonio Quartulli <antonio@openvpn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4032f8ed10 upstream.
OVS_ACTION_ATTR_TRUNC currently stores a delta from the original skb
length in OVS_CB(skb)->cutlen. When a later userspace action segments a
GSO skb, queue_gso_packets() reuses that delta for each smaller segment.
A segment can then reach queue_userspace_packet() with cutlen greater
than skb->len, underflowing the length passed to skb_zerocopy().
Store the maximum preserved length instead and bound each consumer
against the current skb length. Use U32_MAX as the no-truncation
sentinel so the value remains valid if skb geometry changes before a
consumer handles it.
Fixes: f2a4d086ed ("openvswitch: Add packet truncation support.")
Cc: stable@vger.kernel.org
Assisted-by: Codex:gpt-5.5
Signed-off-by: Kyle Zeng <kylebot@openai.com>
Reviewed-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20260707221635.27489-1-kylebot@openai.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 793b9b729f upstream.
The MCTP serial receive state machine reads a frame length byte in
mctp_serial_push_header() case 2 and validates it upper-bound-only:
if (c > MCTP_SERIAL_FRAME_MTU) {
dev->rxstate = STATE_ERR;
} else {
dev->rxlen = c;
dev->rxpos = 0;
dev->rxstate = STATE_DATA;
...
}
A length of zero passes this check, so rxlen is set to 0 and the state
machine advances to STATE_DATA. In mctp_serial_push() STATE_DATA, the
incoming byte is stored and rxpos incremented before the terminator is
tested:
dev->rxbuf[dev->rxpos] = c;
dev->rxpos++;
dev->rxstate = STATE_DATA;
if (dev->rxpos == dev->rxlen) {
dev->rxpos = 0;
dev->rxstate = STATE_TRAILER;
}
With rxlen == 0 the "rxpos == rxlen" terminator can never fire (rxpos is
already 1 on the first data byte), so subsequent bytes are written past
the end of the fixed 74-byte rxbuf, which is the last member of the
netdev private area. Every following data byte is an attacker-controlled
1-byte out-of-bounds heap write, and the overflow continues until a
frame (0x7e) or escape byte resets the parser -- effectively unbounded.
Reaching this requires CAP_NET_ADMIN to attach the N_MCTP line
discipline and bring the resulting mctpserialN netdev up, after which
the bytes arrive via the tty receive path.
Route a zero-length frame straight to STATE_TRAILER instead of
STATE_DATA. The trailer/framing bytes are still consumed, and the frame
resolves to a zero-length skb that the MCTP core rejects; the parser
never enters STATE_DATA with rxlen == 0, so the out-of-bounds write can
no longer occur.
KASAN, on a frame of 0x7e 0x01 0x00 followed by data bytes (before this
change):
UBSAN: array-index-out-of-bounds in drivers/net/mctp/mctp-serial.c:370
index 74 is out of range for type 'u8 [74]'
BUG: KASAN: slab-out-of-bounds in mctp_serial_tty_receive_buf
Write of size 1 at addr ... by task kworker/u16:0
mctp_serial_tty_receive_buf
tty_ldisc_receive_buf
flush_to_ldisc
Allocated by task 152:
alloc_netdev_mqs
mctp_serial_open
v2: route zero-length frames to STATE_TRAILER instead of STATE_ERR so
the trailer/framing bytes are still consumed (Jeremy Kerr).
Found by 0sec automated security-research tooling (https://0sec.ai).
Fixes: a0c2ccd9b5 ("mctp: Add MCTP-over-serial transport binding")
Cc: stable@vger.kernel.org
Suggested-by: Jeremy Kerr <jk@codeconstruct.com.au>
Assisted-by: 0sec:multi-model
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260715082021.46315-1-doruk@0sec.ai
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd3a3f28ed upstream.
llsec_do_decrypt_auth() computes the associated-data length for the
AEAD request as
assoclen += datalen - authlen;
where datalen is the number of bytes after the MAC header and authlen
(4, 8 or 16) is the length of the authentication tag. Nothing verifies
that the frame actually carries at least authlen payload bytes. A
secured frame whose payload is shorter than the tag makes
datalen - authlen negative; assoclen is then passed to
aead_request_set_ad() as an unsigned value close to 4 GiB, so
crypto_aead_decrypt() walks far off the end of the scatterlist that
only spans the real frame.
The frame is fully attacker-controlled and reaches this path from any
IEEE 802.15.4 peer in radio range. Reject frames whose payload is
shorter than the authentication tag before the subtraction.
Dynamically reproduced on a KASAN kernel as a general-protection-fault
in the AEAD scatterwalk, and the fix confirmed.
Fixes: 4c14a2fb5d ("mac802154: add llsec decryption method")
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Link: https://patch.msgid.link/20260716193423.32498-1-doruk@0sec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 234e5e898b upstream.
mac802154_scan_worker() captures the scanning sub-interface under RCU
and then keeps dereferencing sdata->dev after rcu_read_unlock() and
outside the rtnl -- in the failure traces, in
mac802154_transmit_beacon_req() (skb->dev = sdata->dev), and in the
end_scan cleanup. Nothing keeps that netdev alive across the worker
iteration.
A concurrent DEL_INTERFACE or PHY removal can unregister the interface
once the worker drops the rtnl between its two drv_set_channel()
sections. unregister_netdevice() frees the netdev asynchronously from
netdev_run_todo() with the rtnl already dropped, so neither holding the
rtnl nor the per-PHY IEEE802154_IS_SCANNING flag prevents a stale worker
iteration from dereferencing the freed netdev -- a KASAN
slab-use-after-free, reachable by racing TRIGGER_SCAN against
DEL_INTERFACE (both CAP_NET_ADMIN).
Pin the netdev with netdev_hold() while the RCU read lock is still held,
and release it at every worker exit.
Fixes: 57588c7117 ("mac802154: Handle passive scanning")
Cc: stable@vger.kernel.org
Signed-off-by: Ibrahim Hashimov <security@auditcode.ai>
Link: https://patch.msgid.link/20260721211228.34578-1-security@auditcode.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92d3817649 upstream.
ila_csum_adjust_transport() caches ip6h = ipv6_hdr(skb) before calling
pskb_may_pull(). On a non-linear skb whose transport header sits in a page
fragment, pskb_may_pull() can call __pskb_pull_tail() / pskb_expand_head()
and free the old skb head, leaving ip6h dangling; the following
get_csum_diff(ip6h, p) then reads freed memory. ila_update_ipv6_locator()
uses ip6h (and the iaddr derived from it) again after the csum-adjust
call and additionally writes the new locator through that pointer.
Impact: a remote IPv6 packet routed through a configured ILA
csum-adjust-transport route or receive-side mapping triggers a
slab-use-after-free in ila_update_ipv6_locator() (KASAN). The route or
mapping requires CAP_NET_ADMIN to configure, but trigger packets are
unauthenticated once it exists.
Reload ip6h after each pskb_may_pull() in ila_csum_adjust_transport()
before the csum-diff read. In ila_update_ipv6_locator() only the
ILA_CSUM_ADJUST_TRANSPORT case pulls the skb, so reload ip6h and iaddr in
that case alone before the destination-address write; the neutral-map
modes never pull and keep their cached pointers.
Fixes: 33f11d1614 ("ila: Create net/ipv6/ila directory")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://patch.msgid.link/20260714114903.3763420-1-michael.bommarito@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b65352a1ba upstream.
When the system is under extreme memory pressure, page allocations can
fail during the Rx buffer refill loop. If the number of buffers posted
to hardware falls below a critical low threshold and the refill loop
exits due to allocation failures, the queue can stall:
1. The device drops incoming packets because there are no descriptors.
2. Since no packets are processed, no Rx completions are generated.
3. Because no completions occur, NAPI is never scheduled, preventing
the refill loop from running again even after memory is freed.
This results in a permanent queue stall.
Resolve this by introducing a starvation recovery timer for each Rx queue.
If the number of buffers posted to hardware falls below a critical low
threshold, start a timer to periodically reschedule NAPI. Once NAPI runs
and successfully refills the queue above the threshold, the timer is
not rescheduled.
The threshold is set to 32 because a single maximum-sized Receive Segment
Coalescing (RSC) packet can consume up to 19 descriptors in the Rx path.
Lower thresholds (such as 8 or 16) would be insufficient to process a
complete maximum-sized RSC packet, risking packet drops or unexpected
hardware behavior under memory pressure. Setting the threshold to 32
guarantees a safe margin to handle at least one full RSC packet.
Cc: stable@vger.kernel.org
Fixes: 9b8dd5e5ea ("gve: DQO: Add RX path")
Reviewed-by: Jordan Rhee <jordanrhee@google.com>
Signed-off-by: Eddie Phillips <eddiephillips@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20260709211906.3322883-1-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c74801ee52 upstream.
In ntlm_authenticate(), destroy_previous_session() is called using a
user pointer resolved from the client-supplied NTLM blob username field
before the NTLMv2 response is validated. An authenticated attacker can
set the NTLM blob username to match a victim account and set
PreviousSessionId to the victim's session ID; destroy_previous_session()
destroys the victim's session while ksmbd_decode_ntlmssp_auth_blob()
subsequently rejects the request with -EPERM.
Move destroy_previous_session() and the prev_id assignment to after
ksmbd_decode_ntlmssp_auth_blob() returns success and use sess->user
rather than the pre-authentication lookup result. This matches the
ordering already used by krb5_authenticate(), where
destroy_previous_session() is called only after
ksmbd_krb5_authenticate() returns success.
Fixes: e2f34481b2 ("cifsd: add server-side procedures for SMB3")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-cifs/20260702155449.3639773-1-james_montgomery@disroot.org/
Signed-off-by: James Montgomery <james_montgomery@disroot.org>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2eb74eef4b upstream.
The macOS built-in SMB server returns STATUS_STOPPED_ON_SYMLINK for a
CREATE on a path whose final component is a symlink, but it does not
include a Symbolic Link Error Response in the error data: both
ErrorContextCount and ByteCount are zero, so the symlink target is not
present in the response at all. Per [MS-SMB2] section 2.2.2 such a
response should carry a valid Symbolic Link Error Response, so this is a
server bug, but the target can still be retrieved with
FSCTL_GET_REPARSE_POINT.
Frame from a capture against macOS 26.5.2 (build 25F84):
SMB2 hdr : Status=0x8000002d STATUS_STOPPED_ON_SYMLINK, Cmd=Create
Error Rsp: StructureSize=0x0009
Error Context Count: 0
Byte Count: 0
Error Data: 00
symlink_data() cannot find a struct smb2_symlink_err_rsp in such a
response and returns -EINVAL, which parse_create_response() propagates,
so smb2_query_path_info() bails out at
if (rc || !data->reparse_point)
goto out;
before it can retry with SMB2_OP_GET_REPARSE. stat(), readlink() and ls
of any server-side symlink then fail with -EINVAL:
$ ls -la Config
l????????? ? ? ? ? ? Config.json
$ stat Config/Config.json
stat: cannot statx 'Config/Config.json': Invalid argument
A 5.10 client resolves these symlinks correctly against the same server
and share, so this is a regression for Apple SMB servers.
Handle it in several places:
- symlink_data() detects the empty response (ErrorContextCount and
ByteCount both zero) and returns a distinct -ENODATA, so that "server
did not send the target" can be told apart from a genuinely malformed
response and only this case is worked around.
- parse_create_response() treats -ENODATA like
STATUS_IO_REPARSE_TAG_NOT_HANDLED, which does not carry the target
either: leave the reparse tag unset and clear rc, so the existing
SMB2_OP_GET_REPARSE path retrieves the target.
- smb2_query_path_info() only fixes up the symlink target type when the
target is already known. SMB2_OP_GET_REPARSE sets data->reparse.tag
but does not parse the target out of the reparse buffer; that happens
later, in reparse_info_to_fattr(). Without this check
smb2_fix_symlink_target_type() is called with a NULL target and
returns -EIO. This could not happen with servers that send the target
inline and therefore skip SMB2_OP_GET_REPARSE.
- smb2_open_file() maps -ENODATA to -EIO, matching
STATUS_IO_REPARSE_TAG_NOT_HANDLED, so its callers retrieve the target
with SMB2_OP_GET_REPARSE as well.
Tested on Debian 13, kernel 6.18.38 (armv7), against macOS 26.5.2:
symlinks now resolve, including relative, parent-traversing and directory
symlinks, and reads through symlinks succeed.
Cc: stable@vger.kernel.org
Co-developed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Carl Johnson <carl@jpartners.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6c4250b81 upstream.
In a reply message to an RBD request, a positive result code indicates
a data payload, which is not allowed for writes. While
rbd_osd_req_callback() already resets a positive result code for writes
to zero, rbd_object_map_callback() does not. This allows a corrupted
reply to an object map update to trigger the rbd_assert(*result < 0) in
__rbd_obj_handle_request(). This happens, because
rbd_object_map_callback() calls rbd_obj_handle_request() ->
__rbd_obj_handle_request() and passes this positive result code. From
__rbd_obj_handle_request(), rbd_obj_advance_write() is called, which
leaves the positive result code unchanged and returns true. Therefore,
the if(done && *result) branch is executed in __rbd_obj_handle_request()
and the assertion triggers.
This patch fixes the issue by adjusting the logic in the
rbd_object_map_callback() path. A positive result code for an object map
update is now reset to zero (similar to rbd_osd_req_callback()), and the
message is subsequently handled the same way as if the result code was
zero from the beginning. Additionally, a WARN_ON_ONCE() is added for
this case.
Cc: stable@vger.kernel.org
Fixes: 22e8bd51bb ("rbd: support for object-map and fast-diff")
Signed-off-by: Raphael Zimmer <raphael.zimmer@tu-ilmenau.de>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 749d7aa037 upstream.
do_thaw_all_callback() calls bdev_thaw() while holding sb->s_umount
exclusively. If the block device was frozen via bdev_freeze() dropping
the last block layer freeze reference calls fs_bdev_thaw() which
reacquires s_umount:
do_thaw_all_callback(sb)
super_lock_excl(sb) # holds sb->s_umount
bdev_thaw(sb->s_bdev)
mutex_lock(&bdev->bd_fsfreeze_mutex)
# bd_fsfreeze_count drops 1 -> 0
bd_holder_ops->thaw == fs_bdev_thaw
get_bdev_super(bdev)
bdev_super_lock(bdev, true)
super_lock(sb, true)
down_write(&sb->s_umount) # same task: deadlock
The emergency thaw worker deadlocks against itself holding both
s_umount and bd_fsfreeze_mutex. That fscks any subsequent unmount,
freeze, or thaw of that filesystem and block device.
[ 81.878470] sysrq: Show Blocked State
[ 81.880140] task:kworker/0:1 state:D stack:0 pid:11 tgid:11 ppid:2 task_flags:0x4208060 flags:0x00080000
[ 81.884876] Workqueue: events do_thaw_all
[ 81.886656] Call Trace:
[ 81.887759] <TASK>
[ 81.888763] __schedule+0x579/0x1420
[ 81.890372] schedule+0x3a/0x100
[ 81.891794] schedule_preempt_disabled+0x15/0x30
[ 81.893848] rwsem_down_write_slowpath+0x1ea/0x900
[ 81.895191] ? __pfx_do_thaw_all_callback+0x10/0x10
[ 81.896528] down_write+0xbd/0xc0
[ 81.897505] super_lock+0x91/0x180
[ 81.898457] ? __mutex_lock+0xa99/0x1140
[ 81.900748] ? __mutex_unlock_slowpath+0x1f/0x400
[ 81.902069] bdev_super_lock+0x5b/0x150
[ 81.903132] get_bdev_super+0x10/0x60
[ 81.904042] fs_bdev_thaw+0x23/0xf0
[ 81.904755] bdev_thaw+0x82/0x100
[ 81.905484] do_thaw_all_callback+0x2c/0x50
[ 81.906298] __iterate_supers+0x5d/0x130
[ 81.907067] do_thaw_all+0x20/0x40
[ 81.907739] process_one_work+0x206/0x5e0
[ 81.908545] worker_thread+0x1e2/0x3c0
[ 81.909339] ? __pfx_worker_thread+0x10/0x10
[ 81.910171] kthread+0xf4/0x130
[ 81.910799] ? __pfx_kthread+0x10/0x10
[ 81.911528] ret_from_fork+0x2e2/0x3b0
[ 81.912259] ? __pfx_kthread+0x10/0x10
[ 81.913010] ret_from_fork_asm+0x1a/0x30
[ 81.913806] </TASK>
bdev_super_lock() even documents the violated requirement with
lockdep_assert_not_held(&sb->s_umount).
Acquiring bd_fsfreeze_mutex under s_umount also inverts the
bd_fsfreeze_mutex vs. s_umount ordering established by
bdev_{freeze,thaw}() and can thus ABBA against a concurrent block-layer
freeze even when the recursive path isn't hit.
Fix this by not holding s_umount around the bdev_thaw() loop at all. Pin
the superblock with an active reference instead as
filesystems_freeze_callback() does. The active reference keeps the
superblock from being shut down and so ->s_bdev stays valid without
holding s_umount. The block-layer-held freeze is dropped by
fs_bdev_thaw() with FREEZE_MAY_NEST | FREEZE_HOLDER_USERSPACE exactly as
a regular unfreeze would and thaw_super_locked() handles
filesystem-level freezes as before.
The emergency thaw path has deadlocked like this in one form or
another for a long long time but the current exclusively-held
shape dates back to commit [1] where thaw_bdev() already ended in
thaw_super() with s_umount held by do_thaw_all_callback().
Fixes: 08fdc8a013 ("buffer.c: call thaw_super during emergency thaw") [1]
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260723-work-super-emergency_thaw-v1-1-7c315c600245@kernel.org
Signed-off-by: Christian Brauner (Amutable) <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6a7e00b81 upstream.
If a PF reset occurs when the PTP state is ICE_PTP_UNINIT, then
ice_ptp_rebuild() will update the state to ICE_PTP_ERROR. This will
result in the following PTP release call trace during driver unload:
kernel BUG at lib/list_debug.c:52!
ice_ptp_release+0x332/0x3c0 [ice]
ice_deinit_features.part.0+0x10e/0x120 [ice]
ice_remove+0x100/0x220 [ice]
This was observed when passing PF1 through to a VM. ice_ptp_init()
fails because ctrl_pf is NULL and sets the state to ICE_PTP_UNINIT.
Fix by detecting the ICE_PTP_UNINIT state in ice_ptp_rebuild() and
returning without error, preventing the invalid state transition to
ICE_PTP_ERROR. The only valid path to ICE_PTP_ERROR is from
ICE_PTP_RESETTING after a failed rebuild.
Fixes: 8293e4cb2f ("ice: introduce PTP state machine")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260717185340.3595286-10-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Biggers
Jiayuan Chen
Christian König
Yang Wang
Asad Kamal
Ce Sun
Boyuan Zhang
Luca Coelho
Jakob Linke
Alex Deucher
Ethan Nelson-Moore
James Raphael Tiovalen
Stefano Garzarella
Daehyeon Ko
Yuxiang Yang
Yizhou Zhao
Justin Lai
Asim Viladi Oglu Manizada
Shuvam Pandey
Pavitra Jha
Kyle Zeng
Doruk Tan Ozturk
Ibrahim Hashimov
Michael Bommarito
Sergey Temerkhanov
Aleksandr Loktionov
Eddie Phillips
James Montgomery
Carl Johnson
Raphael Zimmer
Christian Brauner
Paul Greenwalt
Sven Schnelle