[ Upstream commit fc9e18f9e9 ]
Under the following conditions:
* after rounding up by 4 the number of bytes to transfer (this is
related to the controller's internal constraints),
* if this (rounded) amount of data is situated beyond the end of the
device,
* and only in NV-DDR mode,
the Arasan NAND controller timeouts.
This currently can happen in a particular helper used when picking
software ECC algorithms. Let's prevent this situation by refusing to use
the NV-DDR interface with software engines.
Fixes: 4edde60314 ("mtd: rawnand: arasan: Support NV-DDR interface")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211008163640.1753821-1-miquel.raynal@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4caab28a62 ]
The condition register PCI_RCV_INTX is used in irq_mask() and irq_unmask()
callbacks. Accesses to register can occur at the same time without a lock.
Add a lock into each callback to prevent the issue.
And INTX mask and unmask fields in PCL_RCV_INTX register should only be
set/reset for each bit. Clearing by PCL_RCV_INTX_ALL_MASK should be
removed.
INTX status fields in PCL_RCV_INTX register only indicates each INTX
interrupt status, so the handler can't clear by writing 1 to the field.
The status is expected to be cleared by the interrupt origin.
The ack function has no meaning, so should remove it.
Suggested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1631924579-24567-1-git-send-email-hayashi.kunihiko@socionext.com
Fixes: 7e6d5cd88a ("PCI: uniphier: Add UniPhier PCIe host controller support")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78e4d34218 ]
hisi_spi_nor_probe() invokes clk_disable_unprepare() on all paths after
successful call of clk_prepare_enable(). Besides, the clock is enabled by
hispi_spi_nor_prep() and disabled by hispi_spi_nor_unprep(). So at remove
time it is not possible to have the clock enabled. The patch removes
excessive clk_disable_unprepare() from hisi_spi_nor_remove().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: e523f11141 ("mtd: spi-nor: add hisilicon spi-nor flash controller driver")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210709144529.31379-1-novikov@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2667f6b7af ]
I have a ST1633 touch controller which fails to probe due to a timeout
waiting for the controller to become ready. Increasing the minimum
delay to 100ms ensures that the probe sequence completes successfully.
The ST1633 datasheet says nothing about the maximum delay here and the
ST1232 I2C protocol document says "wait until" with no notion of a
timeout.
Since this only runs once during probe, being generous with the timout
seems reasonable and most likely the device will become ready
eventually.
(It may be worth noting that I saw this issue with a PREEMPT_RT patched
kernel which probably has tighter wakeups from usleep_range() than other
preemption models.)
Fixes: f605be6a57 ("Input: st1232 - wait until device is ready before reading resolution")
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210929152609.2421483-1-john@metanate.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c2b46c824 ]
When op_alloc() returns NULL to new_op, no error return code of
orangefs_revalidate_lookup() is assigned.
To fix this bug, ret is assigned with -ENOMEM in this case.
Fixes: 8bb8aefd5a ("OrangeFS: Change almost all instances of the string PVFS2 to OrangeFS.")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64a93dbf25 ]
Partially revert commit 2ce209c42c ("NFS: Wait for requests that are
locked on the commit list"), since it can lead to deadlocks between
commit requests and nfs_join_page_group().
For now we should assume that any locked requests on the commit list are
either about to be removed and committed by another task, or the writes
they describe are about to be retransmitted. In either case, we should
not need to worry.
Fixes: 2ce209c42c ("NFS: Wait for requests that are locked on the commit list")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27ff8187f1 ]
Fix sparse warning:
drivers/opp/of.c:924 _opp_add_static_v2() warn: passing zero to 'ERR_PTR'
For duplicate OPPs 'ret' be set to zero.
Fixes: deac8703da ("PM / OPP: _of_add_opp_table_v2(): increment count only if OPP is added")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d419052bc6 ]
Commit 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value") started
using CRSSVE flag for handling CRS responses.
PCI_EXP_RTCTL_CRSSVE flag is stored only in emulated config space buffer
and there is handler for PCI_EXP_RTCTL register. So every read operation
from config space automatically clears CRSSVE flag as it is not defined in
PCI_EXP_RTCTL read handler.
Fix this by reading current CRSSVE bit flag from emulated space buffer and
appending it to PCI_EXP_RTCTL read response.
Link: https://lore.kernel.org/r/20211005180952.6812-5-kabel@kernel.org
Fixes: 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7be28bd73f ]
drivers/gpu/drm/drm_plane_helper.c: In function 'drm_primary_helper_update':
drivers/gpu/drm/drm_plane_helper.c:113:32: error: 'visible' is used uninitialized [-Werror=uninitialized]
113 | struct drm_plane_state plane_state = {
| ^~~~~~~~~~~
drivers/gpu/drm/drm_plane_helper.c:178:14: note: 'visible' was declared here
178 | bool visible;
| ^~~~~~~
cc1: all warnings being treated as errors
visible is an output, not an input. in practice this use might turn out
OK but it's still UB.
Fixes: df86af9133 ("drm/plane-helper: Add drm_plane_helper_check_state()")
Reviewed-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Signed-off-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20211007063706.305984-1-alex_y_xu@yahoo.ca
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2915fa062 ]
_nfs4_pnfs_v3/v4_ds_connect do
some work
smp_wmb
ds->ds_clp = clp;
And nfs4_ff_layout_prepare_ds currently does
smp_rmb
if(ds->ds_clp)
...
This patch places the smp_rmb after the if. This ensures that following
reads only happen once nfs4_ff_layout_prepare_ds has checked that data
has been properly initialized.
Fixes: d67ae825a5 ("pnfs/flexfiles: Add the FlexFile Layout Driver")
Signed-off-by: Baptiste Lepers <baptiste.lepers@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cec08f452a ]
If the directory changed while we were revalidating the dentry, then
don't update the dentry verifier. There is no value in setting the
verifier to an older value, and we could end up overwriting a more up to
date verifier from a parallel revalidation.
Fixes: efeda80da3 ("NFSv4: Fix revalidation of dentries with delegations")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Benjamin Coddington <bcodding@redhat.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6a361c4ca ]
If we want to revalidate the directory, then just mark the change
attribute as invalid.
Fixes: 13c0b082b6 ("NFS: Replace use of NFS_INO_REVAL_PAGECACHE when checking cache validity")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Benjamin Coddington <bcodding@redhat.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eea413308f ]
Both NFSv3 and NFSv2 generate their change attribute from the ctime
value that was supplied by the server. However the problem is that there
are plenty of servers out there with ctime resolutions of 1ms or worse.
In a modern performance system, this is insufficient when trying to
decide which is the most recent set of attributes when, for instance, a
READ or GETATTR call races with a WRITE or SETATTR.
For this reason, let's revert to labelling the NFSv2/v3 change
attributes as NFS4_CHANGE_TYPE_IS_UNDEFINED. This will ensure we protect
against such races.
Fixes: 7b24dacf08 ("NFS: Another inode revalidation improvement")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8228aea5a ]
The reason for the modification here is that the previous
offset information is incorrect, OFFSET_DEBUGSTAT = 0xE4 is
the correct value.
Fixes: 25708278f8 ("i2c: mediatek: Add i2c support for MediaTek MT8183")
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c4c2c8e6f ]
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding a SPI device ID table.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210927134104.38648-1-broonie@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3109151c47 ]
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210927130240.33693-1-broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f84478e14 ]
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210923194922.53386-4-broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da87639d63 ]
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210923194922.53386-3-broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8719a17613 ]
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210923194922.53386-2-broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b6e27d01a ]
Dan Carpenter says:
The patch d20c11d86d: "nfsd: Protect session creation and client
confirm using client_lock" from Jul 30, 2014, leads to the following
Smatch static checker warning:
net/sunrpc/addr.c:178 rpc_parse_scope_id()
warn: sleeping in atomic context
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: d20c11d86d ("nfsd: Protect session creation and client...")
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46a0dc10fb ]
ebu_nand_probe() read the value of u32 variable "cs" from the device
firmware description and used it as the index for array ebu_host->cs
that can contain MAX_CS (2) elements at most. That could result in
a buffer overflow and various bad consequences later.
Fix the potential buffer overflow by restricting values of "cs" with
MAX_CS in probe.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 0b1039f016 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Co-developed-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210903082653.16441-1-novikov@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d108370c64 ]
clang static analysis reports this representative problem:
label.c:1463:16: warning: Assigned value is garbage or undefined
label->hname = name;
^ ~~~~
In aa_update_label_name(), this the problem block of code
if (aa_label_acntsxprint(&name, ...) == -1)
return res;
On failure, aa_label_acntsxprint() has a more complicated return
that just -1. So check for a negative return.
It was also noted that the aa_label_acntsxprint() main comment refers
to a nonexistent parameter, so clean up the comment.
Fixes: f1bd904175 ("apparmor: add the base fns() for domain labels")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1a090f09f ]
If the driver returns a new MR during rereg it has to fill it with the
IOVA from the proper source. If IB_MR_REREG_TRANS is set then the IOVA is
cmd.hca_va, otherwise the IOVA comes from the old MR. mlx5 for example has
two calls inside rereg_mr:
return create_real_mr(new_pd, umem, mr->ibmr.iova,
new_access_flags);
and
return create_real_mr(new_pd, new_umem, iova, new_access_flags);
Unconditionally overwriting the iova in the newly allocated MR will
corrupt the iova if the first path is used.
Remove the redundant initializations from ib_uverbs_rereg_mr().
Fixes: 6e0954b11c ("RDMA/uverbs: Allow drivers to create a new HW object during rereg_mr")
Link: https://lore.kernel.org/r/4b0a31bbc372842613286a10d7a8cbb0ee6069c7.1635400472.git.leonro@nvidia.com
Signed-off-by: Aharon Landau <aharonl@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdf10ffe8f ]
When registering the IRQ handler fails, do not just return the error code,
this will free the devm_kzalloc()-ed data struct while leaving the queued
work queued and the registered power_supply registered with both of them
now pointing to free-ed memory, resulting in various kernel crashes
soon afterwards.
Instead properly tear-down things on IRQ handler register errors.
Fixes: 703df6c097 ("power: bq27xxx_battery: Reorganize I2C into a module")
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18b8f5b6fc ]
mips_cm_error_report() extracts the cause and other cause from the error
register using shifts. This works fine for the former, as it is stored
in the top bits, and the shift will thus remove all non-related bits.
However, the latter is stored in the bottom bits, hence thus needs masking
to get rid of non-related bits. Without such masking, using it as an
index into the cm2_causes[] array will lead to an out-of-bounds access,
probably causing a crash.
Fix this by using FIELD_GET() instead. Bite the bullet and convert all
MIPS CM handling to the bitfield API, to improve readability and safety.
Fixes: 3885c2b463 ("MIPS: CM: Add support for reporting CM cache errors")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef76eb83a1 ]
Cited patch in the fixes tag clears the features bit during reset.
mlx5 vdpa device feature bits are static decided by device capabilities.
These feature bits (including VIRTIO_NET_F_MAC) are initialized during
device addition time.
Clearing features bit in reset callback cleared the VIRTIO_NET_F_MAC. Due
to this, MAC address provided by the device is not honored.
Fix it by not clearing the static feature bits during reset.
Fixes: 0686082dbf ("vdpa: Add reset callback in vdpa_config_ops")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20211026175519.87795-7-parav@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d142585bce ]
If CONFIG_CONSOLE_POLL=y, and CONFIG_SERIAL_CPM=m (hence
CONFIG_SERIAL_CPM_CONSOLE=n):
drivers/tty/serial/cpm_uart/cpm_uart_core.c:1109:12: warning: ‘udbg_cpm_getc’ defined but not used [-Wunused-function]
1109 | static int udbg_cpm_getc(void)
| ^~~~~~~~~~~~~
drivers/tty/serial/cpm_uart/cpm_uart_core.c:1095:13: warning: ‘udbg_cpm_putc’ defined but not used [-Wunused-function]
1095 | static void udbg_cpm_putc(char c)
| ^~~~~~~~~~~~~
Fix this by making the udbg definitions depend on
CONFIG_SERIAL_CPM_CONSOLE, in addition to CONFIG_CONSOLE_POLL.
Fixes: a60526097f ("tty: serial: cpm_uart: Add udbg support for enabling xmon")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211027075326.3270785-1-geert@linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 778a0cbef5 ]
The setting from the cirrus,ts-inv property should be applied to the
TIP_SENSE_INV bit, as this is the one that actually affects the jack
detect block. The TS_INV bit only swaps the meaning of the PLUG and
UNPLUG interrupts and should always be 1 for the interrupts to have
the normal meaning.
Due to some misunderstanding the driver had been implemented to
configure the TS_INV bit based on the jack switch polarity. This made
the interrupts behave the correct way around, but left the jack detect
block, button detect and analogue circuits always interpreting an open
switch as unplugged.
The signal chain inside the codec is:
SENSE pin -> TIP_SENSE_INV -> TS_INV -> (invert) -> interrupts
|
v
Jack detect,
button detect and
analog control
As the TIP_SENSE_INV already performs the necessary inversion the
TS_INV bit never needs to change. It must always be 1 to yield the
expected interrupt behaviour.
Some extra confusion has arisen because of the additional invert in the
interrupt path, meaning that a value applied to the TS_INV bit produces
the opposite effect of applying it to the TIP_SENSE_INV bit. The ts-inv
property has therefore always had the opposite effect to what might be
expected (0 = inverted, 1 = not inverted). To maintain the meaning of
the ts-inv property it must be inverted when applied to TIP_SENSE_INV.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20211028140902.11786-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cddcd5472a ]
A user reports functional regression for Mackie Onyx 1640i that the device
generates slow sound with ALSA oxfw driver which supports media clock
recovery. Although the device is based on OXFW971 ASIC, it does not
transfer isochronous packet with own event frequency as expected. The
device seems to adjust event frequency according to events in received
isochronous packets in the beginning of packet streaming. This is
unknown quirk.
This commit fixes the regression to turn the recovery off in driver
side. As a result, nominal frequency is used in duplex packet streaming
between device and driver. For stability of sampling rate in events of
transferred isochronous packet, 4,000 isochronous packets are skipped
in the beginning of packet streaming.
Reference: https://github.com/takaswie/snd-firewire-improve/issues/38
Fixes: 029ffc4294 ("ALSA: oxfw: perform sequence replay for media clock recovery")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20211028130325.45772-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6cb20fdc2 ]
set_memory_x() calls pte_mkexec() which sets _PAGE_EXEC.
set_memory_nx() calls pte_exprotec() which clears _PAGE_EXEC.
Book3e has 2 bits, UX and SX, which defines the exec rights
resp. for user (PR=1) and for kernel (PR=0).
_PAGE_EXEC is defined as UX only.
An executable kernel page is set with either _PAGE_KERNEL_RWX
or _PAGE_KERNEL_ROX, which both have SX set and UX cleared.
So set_memory_nx() call for an executable kernel page does
nothing because UX is already cleared.
And set_memory_x() on a non-executable kernel page makes it
executable for the user and keeps it non-executable for kernel.
Also, pte_exec() always returns 'false' on kernel pages, because
it checks _PAGE_EXEC which doesn't include SX, so for instance
the W+X check doesn't work.
To fix this:
- change tlb_low_64e.S to use _PAGE_BAP_UX instead of _PAGE_USER
- sets both UX and SX in _PAGE_EXEC so that pte_exec() returns
true whenever one of the two bits is set and pte_exprotect()
clears both bits.
- Define a book3e specific version of pte_mkexec() which sets
either SX or UX based on UR.
Fixes: 1f9ad21c3b ("powerpc/mm: Implement set_memory() routines")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c41100f9c144dc5b62e5a751b810190c6b5d42fd.1635226743.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1b93cb7e7 ]
Commit 26973fa5ac ("powerpc/mm: use pte helpers in generic code")
changed those two functions to use pte helpers to determine which
bits to clear and which bits to set.
This change was based on the assumption that bits to be set/cleared
are always the same and can be determined by applying the pte
manipulation helpers on __pte(0).
But on platforms like book3e, the bits depend on whether the page
is a user page or not.
For the time being it more or less works because of _PAGE_EXEC being
used for user pages only and exec right being set at all time on
kernel page. But following patch will clean that and output of
pte_mkexec() will depend on the page being a user or kernel page.
Instead of trying to make an even more complicated helper where bits
would become dependent on the final pte value, come back to a more
static situation like before commit 26973fa5ac ("powerpc/mm: use
pte helpers in generic code"), by introducing an 8xx specific
version of __ptep_set_access_flags() and ptep_set_wrprotect().
Fixes: 26973fa5ac ("powerpc/mm: use pte helpers in generic code")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/922bdab3a220781bae2360ff3dd5adb7fe4d34f1.1635226743.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43775e62c4 ]
The wait_for_completion_timeout function returns 0 if timed out or a
positive value if completed. Hence, "less than zero" comparison always
misses timeouts and doesn't kill the URB as it should, leading to
re-sending it while it is active.
Fixes: 42337b9d4d ("HID: add driver for U2F Zero built-in LED and RNG")
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
