commit aac17948a7 upstream.
If ubifs_wbuf_sync() fails we must not write a master node with the
dirty marker cleared.
Otherwise it is possible that in case of an IO error while syncing we
mark the filesystem as clean and UBIFS refuses to recover upon next
mount.
Cc: <stable@vger.kernel.org>
Fixes: 1e51764a3c ("UBIFS: add new flash file system")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d41386d55 upstream.
With commit e948bc8fbe (cpufreq: Cap the default transition delay
value to 10 ms) the cpufreq was not honouring the delay passed via
ACPI (PCCT). Due to which on ARM based platforms using CPPC the
cpufreq governor tries to change the frequency of CPUs faster than
expected.
This leads to continuous error messages like the following.
" ACPI CPPC: PCC check channel failed. Status=0 "
Earlier (without above commit) the default transition delay was
taken form the value passed from PCCT. Use the same value provided
by PCCT to set the transition_delay_us.
Fixes: e948bc8fbe (cpufreq: Cap the default transition delay value to 10 ms)
Signed-off-by: George Cherian <george.cherian@cavium.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7972326a26 upstream.
This can be reproduced by bind/unbind the driver multiple times
in AM3517 board.
Analysis revealed that rtl8187_start() was invoked before probe
finishes(ie. before the mutex is initialized).
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 821 Comm: wpa_supplicant Not tainted 4.9.80-dirty #250
Hardware name: Generic AM3517 (Flattened Device Tree)
[<c010e0d8>] (unwind_backtrace) from [<c010beac>] (show_stack+0x10/0x14)
[<c010beac>] (show_stack) from [<c017401c>] (register_lock_class+0x4f4/0x55c)
[<c017401c>] (register_lock_class) from [<c0176fe0>] (__lock_acquire+0x74/0x1938)
[<c0176fe0>] (__lock_acquire) from [<c0178cfc>] (lock_acquire+0xfc/0x23c)
[<c0178cfc>] (lock_acquire) from [<c08aa2f8>] (mutex_lock_nested+0x50/0x3b0)
[<c08aa2f8>] (mutex_lock_nested) from [<c05f5bf8>] (rtl8187_start+0x2c/0xd54)
[<c05f5bf8>] (rtl8187_start) from [<c082dea0>] (drv_start+0xa8/0x320)
[<c082dea0>] (drv_start) from [<c084d1d4>] (ieee80211_do_open+0x2bc/0x8e4)
[<c084d1d4>] (ieee80211_do_open) from [<c069be94>] (__dev_open+0xb8/0x120)
[<c069be94>] (__dev_open) from [<c069c11c>] (__dev_change_flags+0x88/0x14c)
[<c069c11c>] (__dev_change_flags) from [<c069c1f8>] (dev_change_flags+0x18/0x48)
[<c069c1f8>] (dev_change_flags) from [<c0710b08>] (devinet_ioctl+0x738/0x840)
[<c0710b08>] (devinet_ioctl) from [<c067925c>] (sock_ioctl+0x164/0x2f4)
[<c067925c>] (sock_ioctl) from [<c02883f8>] (do_vfs_ioctl+0x8c/0x9d0)
[<c02883f8>] (do_vfs_ioctl) from [<c0288da8>] (SyS_ioctl+0x6c/0x7c)
[<c0288da8>] (SyS_ioctl) from [<c0107760>] (ret_fast_syscall+0x0/0x1c)
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = cd1ec000
[00000000] *pgd=8d1de831, *pte=00000000, *ppte=00000000
Internal error: Oops: 817 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 821 Comm: wpa_supplicant Not tainted 4.9.80-dirty #250
Hardware name: Generic AM3517 (Flattened Device Tree)
task: ce73eec0 task.stack: cd1ea000
PC is at mutex_lock_nested+0xe8/0x3b0
LR is at mutex_lock_nested+0xd0/0x3b0
Cc: stable@vger.kernel.org
Signed-off-by: Sudhir Sreedharan <ssreedharan@mvista.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb5208b314 upstream.
Older devices with a serdev attached bcm bt hci, use an Interrupt ACPI
resource to describe the IRQ (rather then a GpioInt resource).
These device seem to all claim the IRQ is active-high and seem to all need
a DMI quirk to treat it as active-low. Instead simply always assume that
Interrupt resource specified IRQs are always active-low.
This fixes the bt device not being able to wake the host from runtime-
suspend on the: Asus T100TAM, Asus T200TA, Lenovo Yoga2 and the Toshiba
Encore, without the need to add 4 new DMI quirks for these models.
This also allows us to remove 2 DMI quirks for the Asus T100TA and Asus
T100CHI series. Likely the 2 remaining quirks can also be removed but I
could not find a DSDT of these devices to verify this.
Cc: stable@vger.kernel.org
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=198953
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1554835
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09e35a4a1c upstream.
Patch series "mm/get_user_pages_fast fixes, cleanups", v2.
Turns out get_user_pages_fast and __get_user_pages_fast return different
values on error when given a single page: __get_user_pages_fast returns
0. get_user_pages_fast returns either 0 or an error.
Callers of get_user_pages_fast expect an error so fix it up to return an
error consistently.
Stress the difference between get_user_pages_fast and
__get_user_pages_fast to make sure callers aren't confused.
This patch (of 3):
__gup_benchmark_ioctl does not handle the case where get_user_pages_fast
fails:
- a negative return code will cause a buffer overrun
- returning with partial success will cause use of uninitialized
memory.
[akpm@linux-foundation.org: simplification]
Link: http://lkml.kernel.org/r/1522962072-182137-3-git-send-email-mst@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c61611f709 upstream.
get_user_pages_fast is supposed to be a faster drop-in equivalent of
get_user_pages. As such, callers expect it to return a negative return
code when passed an invalid address, and never expect it to return 0
when passed a positive number of pages, since its documentation says:
* Returns number of pages pinned. This may be fewer than the number
* requested. If nr_pages is 0 or negative, returns 0. If no pages
* were pinned, returns -errno.
When get_user_pages_fast fall back on get_user_pages this is exactly
what happens. Unfortunately the implementation is inconsistent: it
returns 0 if passed a kernel address, confusing callers: for example,
the following is pretty common but does not appear to do the right thing
with a kernel address:
ret = get_user_pages_fast(addr, 1, writeable, &page);
if (ret < 0)
return ret;
Change get_user_pages_fast to return -EFAULT when supplied a kernel
address to make it match expectations.
All callers have been audited for consistency with the documented
semantics.
Link: http://lkml.kernel.org/r/1522962072-182137-4-git-send-email-mst@redhat.com
Fixes: 5b65c4677a ("mm, x86/mm: Fix performance regression in get_user_pages_fast()")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: syzbot+6304bf97ef436580fede@syzkaller.appspotmail.com
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cf1e05157 upstream.
On an Output queue, both EMPTY and PENDING buffer states imply that the
buffer is ready for completion-processing by the upper-layer drivers.
So for a non-QEBSM Output queue, get_buf_states() merges mixed
batches of PENDING and EMPTY buffers into one large batch of EMPTY
buffers. The upper-layer driver (ie. qeth) later distuingishes PENDING
from EMPTY by inspecting the slsb_state for
QDIO_OUTBUF_STATE_FLAG_PENDING.
But the merge logic in get_buf_states() contains a bug that causes us to
erronously also merge ERROR buffers into such a batch of EMPTY buffers
(ERROR is 0xaf, EMPTY is 0xa1; so ERROR & EMPTY == EMPTY).
Effectively, most outbound ERROR buffers are currently discarded
silently and processed as if they had succeeded.
Note that this affects _all_ non-QEBSM device types, not just IQD with CQ.
Fix it by explicitly spelling out the exact conditions for merging.
For extracting the "get initial state" part out of the loop, this relies
on the fact that get_buf_states() is never called with a count of 0. The
QEBSM path already strictly requires this, and the two callers with
variable 'count' make sure of it.
Fixes: 104ea556ee ("qdio: support asynchronous delivery of storage blocks")
Cc: <stable@vger.kernel.org> #v3.2+
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dae55b6fef upstream.
Immediate retry of EQBS after CCQ 96 means that we potentially misreport
the state of buffers inspected during the first EQBS call.
This occurs when
1. the first EQBS finds all inspected buffers still in the initial state
set by the driver (ie INPUT EMPTY or OUTPUT PRIMED),
2. the EQBS terminates early with CCQ 96, and
3. by the time that the second EQBS comes around, the state of those
previously inspected buffers has changed.
If the state reported by the second EQBS is 'driver-owned', all we know
is that the previous buffers are driver-owned now as well. But we can't
tell if they all have the same state. So for instance
- the second EQBS reports OUTPUT EMPTY, but any number of the previous
buffers could be OUTPUT ERROR by now,
- the second EQBS reports OUTPUT ERROR, but any number of the previous
buffers could be OUTPUT EMPTY by now.
Effectively, this can result in both over- and underreporting of errors.
If the state reported by the second EQBS is 'HW-owned', that doesn't
guarantee that the previous buffers have not been switched to
driver-owned in the mean time. So for instance
- the second EQBS reports INPUT EMPTY, but any number of the previous
buffers could be INPUT PRIMED (or INPUT ERROR) by now.
This would result in failure to process pending work on the queue. If
it's the final check before yielding initiative, this can cause
a (temporary) queue stall due to IRQ avoidance.
Fixes: 25f269f173 ("[S390] qdio: EQBS retry after CCQ 96")
Cc: <stable@vger.kernel.org> #v3.2+
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d0d8ed335 upstream.
Commit 1cf03c00e7 "nfit: scrub and register regions in a workqueue"
mistakenly attempts to register a region per BLK aperture. There is
nothing to register for individual apertures as they belong as a set to
a BLK aperture group that are registered with a corresponding
DIMM-control-region. Filter them for registration to prevent some
needless devm_kzalloc() allocations.
Cc: <stable@vger.kernel.org>
Fixes: 1cf03c00e7 ("nfit: scrub and register regions in a workqueue")
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5beb07ad3 upstream.
Resource auditing is using the peer field which is not available
when the rlim data struct is used, because it is a different element
of the same union. Accessing peer during resource auditing could
cause garbage log entries or even oops the kernel.
Move the rlim data block into the same struct as the peer field
so they can be used together.
CC: <stable@vger.kernel.org>
Fixes: 86b92cb782 ("apparmor: move resource checks to using labels")
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98cf5bbff4 upstream.
The existence test is not being properly logged as the signal mapping
maps it to the last entry in the named signal table. This is done
to help catch bugs by making the 0 mapped signal value invalid so
that we can catch the signal value not being filled in.
When fixing the off-by-one comparision logic the reporting of the
existence test was broken, because the logic behind the mapped named
table was hidden. Fix this by adding a define for the name lookup
and using it.
Cc: Stable <stable@vger.kernel.org>
Fixes: f7dc4c9a85 ("apparmor: fix off-by-one comparison on MAXMAPPED_SIG")
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d6340672b upstream.
The code that fixes the crashes in the following commit introduced a small
memory leak:
commit 6a2cf8d366 ("scsi: qla2xxx: Fix crashes in qla2x00_probe_one on probe failure")
Fixing this requires a bit of reworking, which I've explained. Also provide
some code cleanup.
There is a small window in qla2x00_probe_one where if qla2x00_alloc_queues
fails, we end up never freeing req and rsp and leak 0xc0 and 0xc8 bytes
respectively (the sizes of req and rsp).
I originally put in checks to test for this condition which were based on
the incorrect assumption that if ha->rsp_q_map and ha->req_q_map were
allocated, then rsp and req were allocated as well. This is incorrect.
There is a window between these allocations:
ret = qla2x00_mem_alloc(ha, req_length, rsp_length, &req, &rsp);
goto probe_hw_failed;
[if successful, both rsp and req allocated]
base_vha = qla2x00_create_host(sht, ha);
goto probe_hw_failed;
ret = qla2x00_request_irqs(ha, rsp);
goto probe_failed;
if (qla2x00_alloc_queues(ha, req, rsp)) {
goto probe_failed;
[if successful, now ha->rsp_q_map and ha->req_q_map allocated]
To simplify this, we should just set req and rsp to NULL after we free
them. Sounds simple enough? The problem is that req and rsp are pointers
defined in the qla2x00_probe_one and they are not always passed by reference
to the routines that free them.
Here are paths which can free req and rsp:
PATH 1:
qla2x00_probe_one
ret = qla2x00_mem_alloc(ha, req_length, rsp_length, &req, &rsp);
[req and rsp are passed by reference, but if this fails, we currently
do not NULL out req and rsp. Easily fixed]
PATH 2:
qla2x00_probe_one
failing in qla2x00_request_irqs or qla2x00_alloc_queues
probe_failed:
qla2x00_free_device(base_vha);
qla2x00_free_req_que(ha, req)
qla2x00_free_rsp_que(ha, rsp)
PATH 3:
qla2x00_probe_one:
failing in qla2x00_mem_alloc or qla2x00_create_host
probe_hw_failed:
qla2x00_free_req_que(ha, req)
qla2x00_free_rsp_que(ha, rsp)
PATH 1: This should currently work, but it doesn't because rsp and rsp are
not set to NULL in qla2x00_mem_alloc. Easily remedied.
PATH 2: req and rsp aren't passed in at all to qla2x00_free_device but are
derived from ha->req_q_map[0] and ha->rsp_q_map[0]. These are only set up if
qla2x00_alloc_queues succeeds.
In qla2x00_free_queues, we are protected from crashing if these don't exist
because req_qid_map and rsp_qid_map are only set on their allocation. We are
guarded in this way:
for (cnt = 0; cnt < ha->max_req_queues; cnt++) {
if (!test_bit(cnt, ha->req_qid_map))
continue;
PATH 3: This works. We haven't freed req or rsp yet (or they were never
allocated if qla2x00_mem_alloc failed), so we'll attempt to free them here.
To summarize, there are a few small changes to make this work correctly and
(and for some cleanup):
1) (For PATH 1) Set *rsp and *req to NULL in case of failure in
qla2x00_mem_alloc so these are correctly set to NULL back in
qla2x00_probe_one
2) After jumping to probe_failed: and calling qla2x00_free_device,
explicitly set rsp and req to NULL so further calls with these pointers do
not crash, i.e. the free queue calls in the probe_hw_failed section we fall
through to.
3) Fix return code check in the call to qla2x00_alloc_queues. We currently
drop the return code on the floor. The probe fails but the caller of the
probe doesn't have an error code, so it attaches to pci. This can result in
a crash on module shutdown.
4) Remove unnecessary NULL checks in qla2x00_free_req_que,
qla2x00_free_rsp_que, and the egregious NULL checks before kfrees and vfrees
in qla2x00_mem_free.
I tested this out running a scenario where the card breaks at various times
during initialization. I made sure I forced every error exit path in
qla2x00_probe_one.
Cc: <stable@vger.kernel.org> # v4.16
Fixes: 6a2cf8d366 ("scsi: qla2xxx: Fix crashes in qla2x00_probe_one on probe failure")
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ee5671e3a upstream.
Currently scsi_dh_lookup() doesn't check for NULL as a device name. This
combined with nvme over dm-mpath results in the following messages
emitted by device-mapper:
device-mapper: multipath: Could not failover device 259:67: Handler scsi_dh_(null) error 14.
Let scsi_dh_lookup() fail fast on NULL names.
[mkp: typo fix]
Cc: <stable@vger.kernel.org> # v4.16
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 880a3a5325 upstream.
We're neglecting to clear the umask after it's set, which can cause a
later unrelated rpc to (incorrectly) use the same umask if it happens to
be processed by the same thread.
There's a more subtle problem here too:
An NFSv4 compound request is decoded all in one pass before any
operations are executed.
Currently we're setting current->fs->umask at the time we decode the
compound. In theory a single compound could contain multiple creates
each setting a umask. In that case we'd end up using whichever umask
was passed in the *last* operation as the umask for all the creates,
whether that was correct or not.
So, we should just be saving the umask at decode time and waiting to set
it until we actually process the corresponding operation.
In practice it's unlikely any client would do multiple creates in a
single compound. And even if it did they'd likely be from the same
process (hence carry the same umask). So this is a little academic, but
we should get it right anyway.
Fixes: 47057abde5 (nfsd: add support for the umask attribute)
Cc: stable@vger.kernel.org
Reported-by: Lucash Stach <l.stach@pengutronix.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a22ee6c3a upstream.
Commit fd8aa9095a ("xen: optimize xenbus driver for multiple
concurrent xenstore accesses") made a subtle change to the semantic of
xenbus_dev_request_and_reply() and xenbus_transaction_end().
Before on an error response to XS_TRANSACTION_END
xenbus_dev_request_and_reply() would not decrement the active
transaction counter. But xenbus_transaction_end() has always counted the
transaction as finished regardless of the response.
The new behavior is that xenbus_dev_request_and_reply() and
xenbus_transaction_end() will always count the transaction as finished
regardless the response code (handled in xs_request_exit()).
But xenbus_dev_frontend tries to end a transaction on closing of the
device if the XS_TRANSACTION_END failed before. Trying to close the
transaction twice corrupts the reference count. So fix this by also
considering a transaction closed if we have sent XS_TRANSACTION_END once
regardless of the return code.
Cc: <stable@vger.kernel.org> # 4.11
Fixes: fd8aa9095a ("xen: optimize xenbus driver for multiple concurrent xenstore accesses")
Signed-off-by: Simon Gaiser <simon@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 695b46e76b upstream.
Eddie Horng reported that readdir of an overlayfs directory that
was exported via NFSv3 returns entries with d_type set to DT_UNKNOWN.
The reason is that while preparing the response for readdirplus, nfsd
checks inside encode_entryplus_baggage() that a child dentry's inode
number matches the value of d_ino returns by overlayfs readdir iterator.
Because the overlayfs inodes use arbitrary inode numbers that are not
correlated with the values of st_ino/d_ino, NFSv3 falls back to not
encoding d_type. Although this is an allowed behavior, we can fix it for
the case of all overlayfs layers on the same underlying filesystem.
When NFS export is enabled and d_ino is consistent with st_ino
(samefs), set the same value also to i_ino in ovl_fill_inode() for all
overlayfs inodes, nfsd readdirplus sanity checks will pass.
ovl_fill_inode() may be called from ovl_new_inode(), before real inode
was created with ino arg 0. In that case, i_ino will be updated to real
upper inode i_ino on ovl_inode_init() or ovl_inode_update().
Reported-by: Eddie Horng <eddiehorng.tw@gmail.com>
Tested-by: Eddie Horng <eddiehorng.tw@gmail.com>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Fixes: 8383f17488 ("ovl: wire up NFS export operations")
Cc: <stable@vger.kernel.org> #v4.16
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ec9b3fafc upstream.
As of now if we encounter an opaque dir while looking for a dentry, we set
d->last=true. This means that there is no need to look further in any of
the lower layers. This works fine as long as there are no redirets or
relative redircts. But what if there is an absolute redirect on the
children dentry of opaque directory. We still need to continue to look into
next lower layer. This patch fixes it.
Here is an example to demonstrate the issue. Say you have following setup.
upper: /redirect (redirect=/a/b/c)
lower1: /a/[b]/c ([b] is opaque) (c has absolute redirect=/a/b/d/)
lower0: /a/b/d/foo
Now "redirect" dir should merge with lower1:/a/b/c/ and lower0:/a/b/d.
Note, despite the fact lower1:/a/[b] is opaque, we need to continue to look
into lower0 because children c has an absolute redirect.
Following is a reproducer.
Watch me make foo disappear:
$ mkdir lower middle upper work work2 merged
$ mkdir lower/origin
$ touch lower/origin/foo
$ mount -t overlay none merged/ \
-olowerdir=lower,upperdir=middle,workdir=work2
$ mkdir merged/pure
$ mv merged/origin merged/pure/redirect
$ umount merged
$ mount -t overlay none merged/ \
-olowerdir=middle:lower,upperdir=upper,workdir=work
$ mv merged/pure/redirect merged/redirect
Now you see foo inside a twice redirected merged dir:
$ ls merged/redirect
foo
$ umount merged
$ mount -t overlay none merged/ \
-olowerdir=middle:lower,upperdir=upper,workdir=work
After mount cycle you don't see foo inside the same dir:
$ ls merged/redirect
During middle layer lookup, the opaqueness of middle/pure is left in
the lookup state and then middle/pure/redirect is wrongly treated as
opaque.
Fixes: 02b69b284c ("ovl: lookup redirects")
Cc: <stable@vger.kernel.org> #v4.10
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 452061fd45 upstream.
d->last signifies that this is the last layer we are looking into and there
is no more. And that means this allows for some optimzation opportunities
during lookup. For example, in ovl_lookup_single() we don't have to check
for opaque xattr of a directory is this is the last layer we are looking
into (d->last = true).
But knowing for sure whether we are looking into last layer can be very
tricky. If redirects are not enabled, then we can look at poe->numlower and
figure out if the lookup we are about to is last layer or not. But if
redircts are enabled then it is possible poe->numlower suggests that we are
looking in last layer, but there is an absolute redirect present in found
element and that redirects us to a layer in root and that means lookup will
continue in lower layers further.
For example, consider following.
/upperdir/pure (opaque=y)
/upperdir/pure/foo (opaque=y,redirect=/bar)
/lowerdir/bar
In this case pure is "pure upper". When we look for "foo", that time
poe->numlower=0. But that alone does not mean that we will not search for a
merge candidate in /lowerdir. Absolute redirect changes that.
IOW, d->last should not be set just based on poe->numlower if redirects are
enabled. That can lead to setting d->last while it should not have and that
means we will not check for opaque xattr while we should have.
So do this.
- If redirects are not enabled, then continue to rely on poe->numlower
information to determine if it is last layer or not.
- If redirects are enabled, then set d->last = true only if this is the
last layer in root ovl_entry (roe).
Suggested-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 02b69b284c ("ovl: lookup redirects")
Cc: <stable@vger.kernel.org> #v4.10
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bffa9909a6 upstream.
From commit 4b855ad371 ("blk-mq: Create hctx for each present CPU),
blk-mq doesn't remap queue after CPU topo is changed, that said when
some of these offline CPUs become online, they are still mapped to
hctx 0, then hctx 0 may become the bottleneck of IO dispatch and
completion.
This patch sets up the mapping from the beginning, and aligns to
queue mapping for PCI device (blk_mq_pci_map_queues()).
Cc: Stefan Haberland <sth@linux.vnet.ibm.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: stable@vger.kernel.org
Fixes: 4b855ad371 ("blk-mq: Create hctx for each present CPU)
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1c735fb79 upstream.
From commit 20e4d81393 (blk-mq: simplify queue mapping & schedule
with each possisble CPU), one hctx can be mapped from all offline CPUs,
then hctx->next_cpu can be set as wrong.
This patch fixes this issue by making hctx->next_cpu pointing to the
first CPU in hctx->cpumask if all CPUs in hctx->cpumask are offline.
Cc: Stefan Haberland <sth@linux.vnet.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Fixes: 20e4d81393 ("blk-mq: simplify queue mapping & schedule with each possisble CPU")
Cc: stable@vger.kernel.org
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bca799b92 upstream.
This patch orders getting budget and driver tag by making sure to acquire
driver tag after budget is got, this way can help to avoid the following
race:
1) before dispatch request from scheduler queue, get one budget first, then
dequeue a request, call it request A.
2) in another IO path for dispatching request B which is from hctx->dispatch,
driver tag is got, then try to get budget in blk_mq_dispatch_rq_list(),
unfortunately the budget is held by request A.
3) meantime blk_mq_dispatch_rq_list() is called for dispatching request
A, and try to get driver tag first, unfortunately no driver tag is
available because the driver tag is held by request B
4) both two IO pathes can't move on, and IO stall is caused.
This issue can be observed when running dbench on USB storage.
This patch fixes this issue by always getting budget before getting
driver tag.
Cc: stable@vger.kernel.org
Fixes: de14829740 ("blk-mq: introduce .get_budget and .put_budget in blk_mq_ops")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2079699c10 upstream.
If a task is holding a reference to a namespace on a removed controller,
the head will not be released. If the same controller is added again
later, its namespaces may not be successfully added. Instead, the user
will see kernel message "Duplicate IDs for nsid <X>".
This patch fixes that by skipping heads that don't have namespaces when
considering if a new namespace is safe to add.
Reported-by: Alex Gagniuc <Alex_Gagniuc@Dellteam.com>
Cc: stable@vger.kernel.org
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 818e0fa293 upstream.
scsi_device_quiesce() uses synchronize_rcu() to guarantee that the
effect of blk_set_preempt_only() will be visible for percpu_ref_tryget()
calls that occur after the queue unfreeze by using the approach
explained in https://lwn.net/Articles/573497/. The rcu read lock and
unlock calls in blk_queue_enter() form a pair with the synchronize_rcu()
call in scsi_device_quiesce(). Both scsi_device_quiesce() and
blk_queue_enter() must either use regular RCU or RCU-sched.
Since neither the RCU-protected code in blk_queue_enter() nor
blk_queue_usage_counter_release() sleeps, regular RCU protection
is sufficient. Note: scsi_device_quiesce() does not have to be
modified since it already uses synchronize_rcu().
Reported-by: Tejun Heo <tj@kernel.org>
Fixes: 3a0a529971 ("block, scsi: Make SCSI quiesce and resume work reliably")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Oleksandr Natalenko <oleksandr@natalenko.name>
Cc: Martin Steigerwald <martin@lichtvoll.de>
Cc: stable@vger.kernel.org # v4.15
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3aefb6a70 upstream.
make_checksum_hmac_md5() is allocating an HMAC transform and doing
crypto API calls in the following order:
crypto_ahash_init()
crypto_ahash_setkey()
crypto_ahash_digest()
This is wrong because it makes no sense to init() the request before a
key has been set, given that the initial state depends on the key. And
digest() is short for init() + update() + final(), so in this case
there's no need to explicitly call init() at all.
Before commit 9fa68f6200 ("crypto: hash - prevent using keyed hashes
without setting key") the extra init() had no real effect, at least for
the software HMAC implementation. (There are also hardware drivers that
implement HMAC-MD5, and it's not immediately obvious how gracefully they
handle init() before setkey().) But now the crypto API detects this
incorrect initialization and returns -ENOKEY. This is breaking NFS
mounts in some cases.
Fix it by removing the incorrect call to crypto_ahash_init().
Reported-by: Michael Young <m.a.young@durham.ac.uk>
Fixes: 9fa68f6200 ("crypto: hash - prevent using keyed hashes without setting key")
Fixes: fffdaef2eb ("gss_krb5: Add support for rc4-hmac encryption")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a774635db5 upstream.
The APIC ID as parsed from ACPI MADT is validity checked with the
apic->apic_id_valid() callback, which depends on the selected APIC type.
For non X2APIC types APIC IDs >= 0xFF are invalid, but values > 0x7FFFFFFF
are detected as valid. This happens because the 'apicid' argument of the
apic_id_valid() callback is type 'int'. So the resulting comparison
apicid < 0xFF
evaluates to true for all unsigned int values > 0x7FFFFFFF which are handed
to default_apic_id_valid(). As a consequence, invalid APIC IDs in !X2APIC
mode are considered valid and accounted as possible CPUs.
Change the apicid argument type of the apic_id_valid() callback to u32 so
the evaluation is unsigned and returns the correct result.
[ tglx: Massaged changelog ]
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: jgross@suse.com
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/1523322966-10296-1-git-send-email-lirongqing@baidu.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9820e1c337 upstream.
Consistently use types provided by <linux/types.h> to fix the following
asm/bootparam.h userspace compilation errors:
/usr/include/asm/bootparam.h:140:2: error: unknown type name 'u16'
u16 version;
/usr/include/asm/bootparam.h:141:2: error: unknown type name 'u16'
u16 compatible_version;
/usr/include/asm/bootparam.h:142:2: error: unknown type name 'u16'
u16 pm_timer_address;
/usr/include/asm/bootparam.h:143:2: error: unknown type name 'u16'
u16 num_cpus;
/usr/include/asm/bootparam.h:144:2: error: unknown type name 'u64'
u64 pci_mmconfig_base;
/usr/include/asm/bootparam.h:145:2: error: unknown type name 'u32'
u32 tsc_khz;
/usr/include/asm/bootparam.h:146:2: error: unknown type name 'u32'
u32 apic_khz;
/usr/include/asm/bootparam.h:147:2: error: unknown type name 'u8'
u8 standard_ioapic;
/usr/include/asm/bootparam.h:148:2: error: unknown type name 'u8'
u8 cpu_ids[255];
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: <stable@vger.kernel.org> # v4.16
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 4a362601ba ("x86/jailhouse: Add infrastructure for running in non-root cell")
Link: http://lkml.kernel.org/r/20180405043210.GA13254@altlinux.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 182b191710 upstream.
When ath9k was switched over to use the mac80211 intermediate queues,
node cleanup now drains the mac80211 queues. However, this call path is
not protected by rcu_read_lock() as it was previously entirely internal
to the driver which uses its own locking.
This leads to a possible rcu_dereference() without holding
rcu_read_lock(); but only if a station is cleaned up while having
packets queued on the TXQ. Fix this by adding the rcu_read_lock() to the
caller in ath9k.
Fixes: 50f08edf98 ("ath9k: Switch to using mac80211 intermediate software queues.")
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68627a697c upstream.
Currently, bank 4 is reserved on Fam17h, so we chose not to initialize
bank 4 in the smca_banks array. This means that when we check if a bank
is initialized, like during boot or resume, we will see that bank 4 is
not initialized and try to initialize it.
This will cause a call trace, when resuming from suspend, due to
rdmsr_*on_cpu() calls in the init path. The rdmsr_*on_cpu() calls issue
an IPI but we're running with interrupts disabled. This triggers:
WARNING: CPU: 0 PID: 11523 at kernel/smp.c:291 smp_call_function_single+0xdc/0xe0
...
Reserved banks will be read-as-zero, so their MCA_IPID register will be
zero. So, like the smca_banks array, the threshold_banks array will not
have an entry for a reserved bank since all its MCA_MISC* registers will
be zero.
Enumerate a "Reserved" bank type that matches on a HWID_MCATYPE of 0,0.
Use the "Reserved" type when checking if a bank is reserved. It's
possible that other bank numbers may be reserved on future systems.
Don't try to find the block address on reserved banks.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # 4.14.x
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180221101900.10326-7-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c02216acf4 upstream.
In randconfig testing, we sometimes get this warning:
drivers/gpu/drm/radeon/radeon_object.c: In function 'radeon_bo_create':
drivers/gpu/drm/radeon/radeon_object.c:242:2: error: #warning Please enable CONFIG_MTRR and CONFIG_X86_PAT for better performance thanks to write-combining [-Werror=cpp]
#warning Please enable CONFIG_MTRR and CONFIG_X86_PAT for better performance \
This is rather annoying since almost all other code produces no build-time
output unless we have found a real bug. We already fixed this in the
amdgpu driver in commit 31bb90f1cd ("drm/amdgpu: shut up #warning for
compile testing") by adding a CONFIG_COMPILE_TEST check last year and
agreed to do the same here, but both Michel and I then forgot about it
until I came across the issue again now.
For stable kernels, as this is one of very few remaining randconfig
warnings in 4.14.
Cc: stable@vger.kernel.org
Link: https://patchwork.kernel.org/patch/9550009/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91d29b288a upstream.
timestamp_insn_cnt is used to estimate the timestamp based on the number of
instructions since the last known timestamp.
If the estimate is not accurate enough decoding might not be correctly
synchronized with side-band events causing more trace errors.
However there are always timestamps following an overflow, so the
estimate is not needed and can indeed result in more errors.
Suppress the estimate by setting timestamp_insn_cnt to zero.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1520431349-30689-5-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Richard Weinberger
Gregory CLEMENT
George Cherian
Hans de Goede
Greg Kroah-Hartman
Sudhir Sreedharan
Szymon Janc
Al Viro
Michael S. Tsirkin
Heiko Carstens
Vasily Gorbik
Julian Wiedmann
Dan Williams
Tetsuo Handa
John Johansen
Bart Van Assche
Bill Kuzeja
Johannes Thumshirn
J. Bruce Fields
Mike Kravetz
Simon Gaiser
Amir Goldstein
Vivek Goyal
Ming Lei
Tejun Heo
Huacai Chen
Yury Norov
Keith Busch
Yunlong Song
Eric Biggers
Li RongQing
Dmitry V. Levin
Toke Høiland-Jørgensen
Yazen Ghannam
Arnd Bergmann
Prashant Bhole
Adrian Hunter