When a Bluetooth controller encounters a coredump, it triggers the
Subsystem Restart (SSR) mechanism. The controller first reports the
coredump data and, once the upload is complete, sends a hw_error
event. The host relies on this event to proceed with subsequent
recovery actions.
If the host has not finished processing the coredump data when the
hw_error event is received, it waits until either the processing is
complete or the 8-second timeout expires before handling the event.
The current implementation clears QCA_MEMDUMP_COLLECTION using
clear_bit(), which does not wake up waiters sleeping in
wait_on_bit_timeout(). As a result, the waiting thread may remain
blocked until the timeout expires even if the coredump collection
has already completed.
Fix this by clearing QCA_MEMDUMP_COLLECTION with
clear_and_wake_up_bit(), which also wakes up the waiting thread and
allows the hw_error handling to proceed immediately.
Test case:
- Trigger a controller coredump using:
hcitool cmd 0x3f 0c 26
- Tested on QCA6390.
- Capture HCI logs using btmon.
- Verify that the delay between receiving the hw_error event and
initiating the power-off sequence is reduced compared to the
timeout-based behavior.
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use strscpy() instead of snprintf() to copy plain strings with no format
specifiers.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_conn lookup and field access must be covered by hdev lock in
hci_user_passkey_notify_evt() and hci_keypress_notify_evt(), otherwise
the connection can be freed concurrently.
Extend the hci_dev_lock critical section to cover all conn usage in both
handlers.
Keep the existing keypress notification behavior unchanged by routing
the early exits through a common unlock path.
Fixes: 92a25256f1 ("Bluetooth: mgmt: Implement support for passkey notification")
Cc: stable@vger.kernel.org
Signed-off-by: Shuvam Pandey <shuvampandey1@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
struct hci_std_codecs and struct hci_std_codecs_v2 are flexible
structures, this is structures that contain a flexible-array member
(__u8 codec[]; and struct hci_std_codec_v2 codec[];, correspondingly.)
Since struct hci_rp_read_local_supported_codecs and struct
hci_rp_read_local_supported_codecs_v2 are defined by hardware, we
create the new struct hci_std_codecs_hdr and struct hci_std_codecs_v2_hdr
types, and use them to replace the object types causing trouble in
struct hci_rp_read_local_supported_codecs and struct
hci_rp_read_local_supported_codecs_v2, namely struct hci_std_codecs
std_codecs; and struct hci_std_codecs_v2_hdr std_codecs;.
Also, once -fms-extensions is enabled, we can use transparent struct
members in both struct hci_std_codecs and struct hci_std_codecs_v2_hdr.
Notice that the newly created types does not contain the flex-array
member `codec`, which is the object causing the -Wfamnae warnings.
After these changes, the size of struct hci_rp_read_local_supported_codecs
and struct hci_rp_read_local_supported_codecs_v2, along with their
member's offsets remain the same, hence the memory layouts don't
change:
Before changes:
struct hci_rp_read_local_supported_codecs {
__u8 status; /* 0 1 */
struct hci_std_codecs std_codecs; /* 1 1 */
struct hci_vnd_codecs vnd_codecs; /* 2 1 */
/* size: 3, cachelines: 1, members: 3 */
/* last cacheline: 3 bytes */
} __attribute__((__packed__));
struct hci_rp_read_local_supported_codecs_v2 {
__u8 status; /* 0 1 */
struct hci_std_codecs_v2 std_codecs; /* 1 1 */
struct hci_vnd_codecs_v2 vendor_codecs; /* 2 1 */
/* size: 3, cachelines: 1, members: 3 */
/* last cacheline: 3 bytes */
} __attribute__((__packed__));
After changes:
struct hci_rp_read_local_supported_codecs {
__u8 status; /* 0 1 */
struct hci_std_codecs_hdr std_codecs; /* 1 1 */
struct hci_vnd_codecs vnd_codecs; /* 2 1 */
/* size: 3, cachelines: 1, members: 3 */
/* last cacheline: 3 bytes */
} __attribute__((__packed__));
struct hci_rp_read_local_supported_codecs_v2 {
__u8 status; /* 0 1 */
struct hci_std_codecs_v2_hdr std_codecs; /* 1 1 */
struct hci_vnd_codecs_v2 vendor_codecs; /* 2 1 */
/* size: 3, cachelines: 1, members: 3 */
/* last cacheline: 3 bytes */
} __attribute__((__packed__));
With these changes fix the following warnings:
include/net/bluetooth/hci.h:1490:31: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
include/net/bluetooth/hci.h:1525:34: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
copy_struct_from_sockptr() fill 'buffer' in
sco_sock_setsockopt() with zeros, so there's no
real problem.
But it actually looks strange to do this,
without checking all of codecs->codecs[0]
really comes from userspace:
sco_pi(sk)->codec = codecs->codecs[0];
As only optlen < sizeof(struct bt_codecs) is checked
and codecs->num_codecs is not checked against != 1,
but only <= 1, and the space for the additional struct bt_codec
is not checked.
Note I don't understand bluetooth and I didn't do any runtime
tests with this! I just found it when debugging a problem
in copy_struct_from_sockptr().
I just added this to check the size is as expected:
BUILD_BUG_ON(struct_size(codecs, codecs, 0) != 1);
BUILD_BUG_ON(struct_size(codecs, codecs, 1) != 8);
And made sure it still compiles using this:
make CF=-D__CHECK_ENDIAN__ W=1ce C=1 net/bluetooth/sco.o
Fixes: 3e643e4efa ("Bluetooth: Improve setsockopt() handling of malformed user input")
Cc: Michal Luczaj <mhal@rbox.co>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: David Wei <dw@davidwei.uk>
Cc: linux-bluetooth@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Align each descriptor/index/context region to 128 bytes before
calculating the total DMA pool size. This ensures the memory layout
shared with firmware meets the 128-byte alignment requirement.
The DMA pool alignment is also set to 128 bytes to match the firmware
expectation for all shared structures.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
l2cap_ecred_reconf_rsp() calls l2cap_chan_del() without holding
l2cap_chan_lock(). Every other l2cap_chan_del() caller in the file
acquires the lock first. A remote BLE device can send a crafted
L2CAP ECRED reconfiguration response to corrupt the channel list
while another thread is iterating it.
Add l2cap_chan_hold() and l2cap_chan_lock() before l2cap_chan_del(),
and l2cap_chan_unlock() and l2cap_chan_put() after, matching the
pattern used in l2cap_ecred_conn_rsp() and l2cap_conn_del().
Fixes: 15f02b9105 ("Bluetooth: L2CAP: Add initial code for Enhanced Credit Based Mode")
Signed-off-by: Dudu Lu <phx0fer@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
TI WL183x controllers advertise support for the HCI Enhanced Setup
Synchronous Connection command, but SCO setup fails when the enhanced
path is used. The only working configuration is to fall back to the
legacy HCI Setup Synchronous Connection (0x0028).
This matches the scenario described in commit 05abad8572
("Bluetooth: HCI: Add HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN quirk").
Enable HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN automatically for
devices compatible with:
- ti,wl1831-st
- ti,wl1835-st
- ti,wl1837-st
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add VID 0489 & PID e11d for MediaTek MT7922 USB Bluetooth chip.
Found in Dynabook GA/ZY (W6GAZY5RCL).
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=03 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e11d Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Kamiyama Chiaki <nercone@nercone.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When USB support is disabled, the array is not referenced anywhere,
causing a warning:
drivers/bluetooth/btmtk.c:35:3: error: 'btmtk_mt6639_devs' defined but not used [-Werror=unused-const-variable=]
35 | } btmtk_mt6639_devs[] = {
| ^~~~~~~~~~~~~~~~~
Move it into the #ifdef block.
Fixes: 28b7c5a6db ("Bluetooth: btmtk: Add MT6639 (MT7927) Bluetooth support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some MT6639 Bluetooth USB interfaces (e.g. IMC Networks 13d3:3588 on
ASUS ROG STRIX X870E-E and ProArt X870E-Creator boards) expose only a
single alternate setting (alt 0) on the ISO interface. The driver
unconditionally requests alt setting 1, which fails with EINVAL on
these devices, causing a ~20 second initialization delay and no LE
audio support.
Check the number of available alternate settings before selecting one.
If only alt 0 exists, use it; otherwise request alt 1 as before.
Closes: https://github.com/jetm/mediatek-mt7927-dkms/pull/39
Signed-off-by: Javier Tia <floss@jetm.me>
Reported-by: Ryan Gilbert <xelnaga@gmail.com>
Tested-by: Ryan Gilbert <xelnaga@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The MediaTek MT7927 (Filogic 380) combo WiFi 7 + BT 5.4 module uses
hardware variant 0x6639 for its Bluetooth subsystem. Without this patch,
the chip fails with "Unsupported hardware variant (00006639)" or hangs
during firmware download.
Three changes are needed to support MT6639:
1. CHIPID workaround: On some boards the BT USB MMIO register reads
0x0000 for dev_id, causing the driver to skip the 0x6639 init path.
Force dev_id to 0x6639 only when the USB VID/PID matches a known
MT6639 device, avoiding misdetection if a future chip also reads
zero. This follows the WiFi-side pattern that uses PCI device IDs
to scope the same workaround.
2. Firmware naming: MT6639 uses firmware version prefix "2_1" instead of
"1_1" used by MT7925 and other variants. The firmware path is
mediatek/mt7927/BT_RAM_CODE_MT6639_2_1_hdr.bin, using the mt7927
directory to match the WiFi firmware convention. The filename will
likely change to use MT7927 once MediaTek submits a dedicated
Linux firmware binary.
3. Section filtering: The MT6639 firmware binary contains 9 sections, but
only sections with (dlmodecrctype & 0xff) == 0x01 are Bluetooth-related.
Sending the remaining WiFi/other sections causes an irreversible BT
subsystem hang requiring a full power cycle. This matches the Windows
driver behavior observed via USB captures.
Also add 0x6639 to the reset register (CONNV3) and firmware setup switch
cases alongside the existing 0x7925 handling.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Reported-by: Ryan Gilbert <xelnaga@gmail.com>
Signed-off-by: Javier Tia <floss@jetm.me>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When protocol sets HCI_PROTO_DEFER, hci_conn_request_evt() calls
hci_connect_cfm(conn) without hdev->lock. Generally hci_connect_cfm()
assumes it is held, and if conn is deleted concurrently -> UAF.
Only SCO and ISO set HCI_PROTO_DEFER and only for defer setup listen,
and HCI_EV_CONN_REQUEST is not generated for ISO. In the non-deferred
listening socket code paths, hci_connect_cfm(conn) is called with
hdev->lock held.
Fix by holding the lock.
Fixes: 70c4642563 ("Bluetooth: Refactor connection request handling")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use the common USB helper for looking up bulk and interrupt endpoints
instead of open coding.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use the common USB helper for looking up bulk and interrupt endpoints
instead of open coding.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When hci_register_dev() fails in hci_uart_register_dev()
HCI_UART_PROTO_INIT is not cleared before calling hu->proto->close(hu)
and setting hu->hdev to NULL. This means incoming UART data will reach
the protocol-specific recv handler in hci_uart_tty_receive() after
resources are freed.
Clear HCI_UART_PROTO_INIT with a write lock before calling
hu->proto->close() and setting hu->hdev to NULL. The write lock ensures
all active readers have completed and no new reader can enter the
protocol recv path before resources are freed.
This allows the protocol-specific recv functions to remove the
"HCI_UART_REGISTERED" guard without risking a null pointer dereference
if hci_register_dev() fails.
Fixes: 5df5dafc17 ("Bluetooth: hci_uart: Fix another race during initialization")
Signed-off-by: Jonathan Rissanen <jonathan.rissanen@axis.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_cmd_sync_run_once() needs to indicate whether a queue item was
added, so caller can know if callbacks are called, so it can avoid
leaking resources.
Change the function to return -EEXIST if queue item already exists.
Modify all callsites vs. the changes. The only callsite is
hci_abort_conn().
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On platforms using an M.2 slot with both UART and USB support, bt_en is
pulled high by hardware. In this case, software-based power control
should be disabled. The current platforms are Lemans-EVK and Monaco-EVK.
Add QCA_WCN7850 to the existing condition so that power_ctrl_enabled is
cleared when bt_en is not software-controlled (or absent), aligning its
behavior with WCN6750 and WCN6855
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Replace single space with tab and insert blank line after declaration, according to checkpatch
Signed-off-by: Lukas Kraft <rebootrequired42@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The WCN39xx family of WiFi/BT chips incorporates a simple PMU, spreading
voltages over internal rails. Implement support for using powersequencer
for this family of QCA devices in addition to using regulators.
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add device coredump support for Scorpious Peak2F product.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add device coredump support for Scorpious Peak2 product.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add DSBR support for Scorpious Peak2 cores onwards.
Refer commit eb9e749c01 ("Bluetooth: btintel: Allow configuring drive
strength of BRI") for details about DSBR.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use hardware variant instead of CNVi to send dsbr command.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If FW image has hybrid signature (ECDSA and LMS) then send CSS header,
ECDSA public key, ECDSA signature, LMS public key, LMS signature and
command buffer to device.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Core 6.0, Vol 3, Part A, 3.4.3:
"... If the payload size of any K-frame exceeds the receiver's MPS, the
receiver shall disconnect the channel..."
This fixes L2CAP/LE/CFC/BV-27-C (running together with 'l2test -r -P
0x0027 -V le_public -I 100').
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Christian Eggers <ceggers@arri.de>
Add MT7902 Bluetooth SDIO support by introducing chip data and
registering the device ID.
Runtime PM is not yet supported by the driver, but normal operation
is unaffected.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add MT7902 device ID and firmware filename to enable MCU firmware
loading.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use struct_size(), which provides additional compile-time checks for
structures with flexible array members (e.g., __must_be_array()), to
determine the allocation size for a new 'struct hci_drv_rp_read_info'.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add USB device ID (04ca:3807) for a Lite-On Wireless_Device containing
a MediaTek MT7921 (MT7920) Bluetooth chipset found in Acer laptops.
Without this entry, btusb binds via the generic USB class-based wildcard
match but never sets the BTUSB_MEDIATEK flag. This means btmtk never
triggers firmware loading, and the driver sends a raw HCI Reset that
the uninitialized chip cannot respond to, resulting in:
Bluetooth: hci0: Opcode 0x0c03 failed: -110
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below:
T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=01 Dev#=5 Spd=480 MxCh=0
P: Vendor=04ca ProdID=3807 Rev=1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C: #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Dylan Eray <dylan.eray6@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Replace snprintf("%s", ...) with the faster and more direct strscpy().
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The BT core skips calling the hci_dev's shutdown method when the HCI
is unregistered. This means that qca_power_off() was not getting called
leaving BT powered on.
This causes regulators / pwrseq providers to not get disabled which also
causes problem when re-loading the module because regulators and pwrseq
providers have an enablecount which now has never dropped to 0, causing
the BT to not get properly reset between rmmod and re-load which causes
initialization failure on the re-load.
Fix this by calling qca_power_off() from qca_close() when BT has not
already been powered off through a qca_hci_shutdown() call.
hci_ldisc.c will call qca_close() after freeing the hdev, so this
means that qca_power_off() can now no longer deref hu->hdev, change
the logging in qca_power_off() to no longer use hu->hdev.
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Shuai Zhang
Thorsten Blum
Shuvam Pandey
Gustavo A. R. Silva
Stefan Metzmacher
Kiran K
Dudu Lu
Stefano Radaelli
Kamiyama Chiaki
Arnd Bergmann
Javier Tia
Pauli Virtanen
Johan Hovold
Jonathan Rissanen
Lukas Kraft
Luiz Augusto von Dentz
Dmitry Baryshkov
Christian Eggers
Sean Wang
Dylan Eray
Hans de Goede