Wei Fang says:
====================
net: fec: fix some PTP related issues
There are some issues which were introduced by the commit 350749b909
("net: fec: Add support for periodic output signal of PPS"). See each
patch for more details.
====================
Link: https://patch.msgid.link/20251125085210.1094306-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are currently two situations that can trigger the PTP interrupt,
one is the PPS event, the other is the PEROUT event. However, the irq
handler fec_pps_interrupt() does not check the irq event type and
directly registers a PPS event into the system, but the event may be
a PEROUT event. This is incorrect because PEROUT is an output signal,
while PPS is the input of the kernel PPS system. Therefore, add a check
for the event type, if pps_enable is true, it means that the current
event is a PPS event, and then the PPS event is registered.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-5-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In the current driver, PPS and PEROUT use the same channel to generate
the events, so they cannot be enabled at the same time. Otherwise, the
later configuration will overwrite the earlier configuration. Therefore,
when configuring PPS, the driver will check whether PEROUT is enabled.
Similarly, when configuring PEROUT, the driver will check whether PPS
is enabled.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-4-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If the previously set PEROUT is already active, updating it will cause
the new PEROUT to start immediately instead of at the specified time.
This is because fep->reload_period is updated whithout check whether
the PEROUT is enabled, and the old PEROUT is not disabled. Therefore,
the pulse period will be updated immediately in the pulse interrupt
handler fec_pps_interrupt().
Currently, the driver does not support directly updating PEROUT and it
will make the logic be more complicated. To fix the current issue, add
a check before enabling the PEROUT, the driver will return an error if
PEROUT is enabled. If users wants to update a new PEROUT, they should
disable the old PEROUT first.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-3-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The PEROUT allows the user to set a specified future time to output the
periodic signal. If the future time is far from the current time, the FEC
driver will use hrtimer to configure PEROUT one second before the future
time. However, the hrtimer will not be canceled if the PEROUT is disabled
before the hrtimer expires. So the PEROUT will be configured when the
hrtimer expires, which is not as expected. Therefore, cancel the hrtimer
in fec_ptp_pps_disable() to fix this issue.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-2-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
On transmit, we are currently relying on skb->dev being set by
mctp_local_output() when we first set up the skb destination fields.
However, forwarded skbs do not use the local_output path, so will retain
their incoming netdev as their ->dev on tx. This does not work when
we're forwarding between interfaces.
Set skb->dev unconditionally in the transmit path, to allow for proper
forwarding.
We keep the skb->dev initialisation in mctp_local_output(), as we use it
for fragmentation.
Fixes: 269936db5e ("net: mctp: separate routing database from routing operations")
Suggested-by: Vince Chang <vince_chang@aspeedtech.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20251125-dev-forward-v1-1-54ecffcd0616@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Marc Kleine-Budde says:
====================
pull-request: can 2025-11-26
this is a pull request of 8 patches for net/main.
Seungjin Bae provides a patch for the kvaser_usb driver to fix a
potential infinite loop in the USB data stream command parser.
Thomas Mühlbacher's patch for the sja1000 driver IRQ handler's max
loop handling, that might lead to unhandled interrupts.
3 patches by me for the gs_usb driver fix handling of failed transmit
URBs and add checking of the actual length of received URBs before
accessing the data.
The next patch is by me and is a port of Thomas Mühlbacher's patch
(fix IRQ handler's max loop handling, that might lead to unhandled
interrupts.) to the sun4i_can driver.
Biju Das provides a patch for the rcar_canfd driver to fix the CAN-FD
mode setting.
The last patch is by Shaurya Rane for the em_canid filter to ensure
that the complete CAN frame is present in the linear data buffer
before accessing it.
* tag 'linux-can-fixes-for-6.18-20251126' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
net/sched: em_canid: fix uninit-value in em_canid_match
can: rcar_canfd: Fix CAN-FD mode as default
can: sun4i_can: sun4i_can_interrupt(): fix max irq loop handling
can: gs_usb: gs_usb_receive_bulk_callback(): check actual_length before accessing data
can: gs_usb: gs_usb_receive_bulk_callback(): check actual_length before accessing header
can: gs_usb: gs_usb_xmit_callback(): fix handling of failed transmitted URBs
can: sja1000: fix max irq loop handling
can: kvaser_usb: leaf: Fix potential infinite loop in command parsers
====================
Link: https://patch.msgid.link/20251126155713.217105-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The atlantic driver can receive packets with more than MAX_SKB_FRAGS (17)
fragments when handling large multi-descriptor packets. This causes an
out-of-bounds write in skb_add_rx_frag_netmem() leading to kernel panic.
The issue occurs because the driver doesn't check the total number of
fragments before calling skb_add_rx_frag(). When a packet requires more
than MAX_SKB_FRAGS fragments, the fragment index exceeds the array bounds.
Fix by assuming there will be an extra frag if buff->len > AQ_CFG_RX_HDR_SIZE,
then all fragments are accounted for. And reusing the existing check to
prevent the overflow earlier in the code path.
This crash occurred in production with an Aquantia AQC113 10G NIC.
Stack trace from production environment:
```
RIP: 0010:skb_add_rx_frag_netmem+0x29/0xd0
Code: 90 f3 0f 1e fa 0f 1f 44 00 00 48 89 f8 41 89
ca 48 89 d7 48 63 ce 8b 90 c0 00 00 00 48 c1 e1 04 48 01 ca 48 03 90
c8 00 00 00 <48> 89 7a 30 44 89 52 3c 44 89 42 38 40 f6 c7 01 75 74 48
89 fa 83
RSP: 0018:ffffa9bec02a8d50 EFLAGS: 00010287
RAX: ffff925b22e80a00 RBX: ffff925ad38d2700 RCX:
fffffffe0a0c8000
RDX: ffff9258ea95bac0 RSI: ffff925ae0a0c800 RDI:
0000000000037a40
RBP: 0000000000000024 R08: 0000000000000000 R09:
0000000000000021
R10: 0000000000000848 R11: 0000000000000000 R12:
ffffa9bec02a8e24
R13: ffff925ad8615570 R14: 0000000000000000 R15:
ffff925b22e80a00
FS: 0000000000000000(0000)
GS:ffff925e47880000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff9258ea95baf0 CR3: 0000000166022004 CR4:
0000000000f72ef0
PKRU: 55555554
Call Trace:
<IRQ>
aq_ring_rx_clean+0x175/0xe60 [atlantic]
? aq_ring_rx_clean+0x14d/0xe60 [atlantic]
? aq_ring_tx_clean+0xdf/0x190 [atlantic]
? kmem_cache_free+0x348/0x450
? aq_vec_poll+0x81/0x1d0 [atlantic]
? __napi_poll+0x28/0x1c0
? net_rx_action+0x337/0x420
```
Fixes: 6aecbba12b ("net: atlantic: add check for MAX_SKB_FRAGS")
Changes in v4:
- Add Fixes: tag to satisfy patch validation requirements.
Changes in v3:
- Fix by assuming there will be an extra frag if buff->len > AQ_CFG_RX_HDR_SIZE,
then all fragments are accounted for.
Signed-off-by: Jiefeng Zhang <jiefeng.z.zhang@gmail.com>
Link: https://patch.msgid.link/20251126032249.69358-1-jiefeng.z.zhang@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit a2fb4bc4e2 ("net: implement virtio helpers to handle UDP
GSO tunneling.") inadvertently altered checksum offload behavior
for guests not using UDP GSO tunneling.
Before, tun_put_user called tun_vnet_hdr_from_skb, which passed
has_data_valid = true to virtio_net_hdr_from_skb.
After, tun_put_user began calling tun_vnet_hdr_tnl_from_skb instead,
which passes has_data_valid = false into both call sites.
This caused virtio hdr flags to not include VIRTIO_NET_HDR_F_DATA_VALID
for SKBs where skb->ip_summed == CHECKSUM_UNNECESSARY. As a result,
guests are forced to recalculate checksums unnecessarily.
Restore the previous behavior by ensuring has_data_valid = true is
passed in the !tnl_gso_type case, but only from tun side, as
virtio_net_hdr_tnl_from_skb() is used also by the virtio_net driver,
which in turn must not use VIRTIO_NET_HDR_F_DATA_VALID on tx.
cc: stable@vger.kernel.org
Fixes: a2fb4bc4e2 ("net: implement virtio helpers to handle UDP GSO tunneling.")
Signed-off-by: Jon Kohler <jon@nutanix.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20251125222754.1737443-1-jon@nutanix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix a potential counter roll-over issue in fbnic_mbx_alloc_rx_msgs()
when calculating descriptor slots. The issue occurs when head - tail
results in a large positive value (unsigned) and the compiler interprets
head - tail - 1 as a signed value.
Since FBNIC_IPC_MBX_DESC_LEN is a power of two, use a masking operation,
which is a common way of avoiding this problem when dealing with these
sort of ring space calculations.
Fixes: da3cde0820 ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Link: https://patch.msgid.link/20251125211704.3222413-1-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When __mptcp_retrans() kicks-in, it schedules one or more subflows for
retransmission, but such subflows could be actually left alone if there
is no more data to retransmit and/or in case of concurrent fallback.
Scheduled subflows could be processed much later in time, i.e. when new
data will be transmitted, leading to bad subflow selection.
Explicitly clear all scheduled subflows before leaving the
retransmission function.
Fixes: ee2708aeda ("mptcp: use get_retrans wrapper")
Cc: stable@vger.kernel.org
Reported-by: Filip Pokryvka <fpokryvk@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251125-net-mptcp-clear-sched-rtx-v1-1-1cea4ad2165f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When using the SGMII PCS as a fixed-link chip-to-chip connection, it is
easy to miss the fact that traffic passes only at 1G, since that's what
any normal such connection would use.
When using the SGMII PCS connected towards an on-board PHY or an SFP
module, it is immediately noticeable that when the link resolves to a
speed other than 1G, traffic from the MAC fails to pass: TX counters
increase, but nothing gets decoded by the other end, and no local RX
counters increase either.
Artificially lowering a fixed-link rate to speed = <100> makes us able
to see the same issue as in the case of having an SGMII PHY.
Some debugging shows that the XPCS configuration is A-OK, but that the
MAC Configuration Table entry for the port has the SPEED bits still set
to 1000Mbps, due to a special condition in the driver. Deleting that
condition, and letting the resolved link speed be programmed directly
into the MAC speed field, results in a functional link at all 3 speeds.
This piece of evidence, based on testing on both generations with SGMII
support (SJA1105S and SJA1110A) directly contradicts the statement from
the blamed commit that "the MAC is fixed at 1 Gbps and we need to
configure the PCS only (if even that)". Worse, that statement is not
backed by any documentation, and no one from NXP knows what it might
refer to.
I am unable to recall sufficient context regarding my testing from March
2020 to understand what led me to draw such a braindead and factually
incorrect conclusion. Yet, there is nothing of value regarding forcing
the MAC speed, either for SGMII or 2500Base-X (introduced at a later
stage), so remove all such logic.
Fixes: ffe10e679c ("net: dsa: sja1105: Add support for the SGMII port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251122111324.136761-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When discarding descriptors with IN_ORDER, we should rewind
next_avail_head otherwise it would run out of sync with
last_avail_idx. This would cause driver to report
"id X is not a head".
Fixing this by returning the number of descriptors that is used for
each buffer via vhost_get_vq_desc_n() so caller can use the value
while discarding descriptors.
Fixes: 67a873df0c ("vhost: basic in order support")
Cc: stable@vger.kernel.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://patch.msgid.link/20251120022950.10117-1-jasowang@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit 5cff263606 ("can: rcar_canfd: Fix controller mode setting")
has aligned with the flow mentioned in the hardware manual for all SoCs
except R-Car Gen3 and RZ/G2L SoCs. On R-Car Gen4 and RZ/G3E SoCs, due to
the wrong logic in the commit[1] sets the default mode to FD-Only mode
instead of CAN-FD mode.
This patch sets the CAN-FD mode as the default for all SoCs by dropping
the rcar_canfd_set_mode() as some SoC requires mode setting in global
reset mode, and the rest of the SoCs in channel reset mode and update the
rcar_canfd_reset_controller() to take care of these constraints. Moreover,
the RZ/G3E and R-Car Gen4 SoCs support 3 modes compared to 2 modes on the
R-Car Gen3. Use inverted logic in rcar_canfd_reset_controller() to
simplify the code later to support FD-only mode.
[1]
commit 45721c406d ("can: rcar_canfd: Add support for r8a779a0 SoC")
Fixes: 5cff263606 ("can: rcar_canfd: Fix controller mode setting")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patch.msgid.link/20251118123926.193445-1-biju.das.jz@bp.renesas.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit 30f241fcf5 ("xsk: Fix immature cq descriptor
production"), the descriptor number is stored in skb control block and
xsk_cq_submit_addr_locked() relies on it to put the umem addrs onto
pool's completion queue.
skb control block shouldn't be used for this purpose as after transmit
xsk doesn't have control over it and other subsystems could use it. This
leads to the following kernel panic due to a NULL pointer dereference.
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP NOPTI
CPU: 2 UID: 1 PID: 927 Comm: p4xsk.bin Not tainted 6.16.12+deb14-cloud-amd64 #1 PREEMPT(lazy) Debian 6.16.12-1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-debian-1.17.0-1 04/01/2014
RIP: 0010:xsk_destruct_skb+0xd0/0x180
[...]
Call Trace:
<IRQ>
? napi_complete_done+0x7a/0x1a0
ip_rcv_core+0x1bb/0x340
ip_rcv+0x30/0x1f0
__netif_receive_skb_one_core+0x85/0xa0
process_backlog+0x87/0x130
__napi_poll+0x28/0x180
net_rx_action+0x339/0x420
handle_softirqs+0xdc/0x320
? handle_edge_irq+0x90/0x1e0
do_softirq.part.0+0x3b/0x60
</IRQ>
<TASK>
__local_bh_enable_ip+0x60/0x70
__dev_direct_xmit+0x14e/0x1f0
__xsk_generic_xmit+0x482/0xb70
? __remove_hrtimer+0x41/0xa0
? __xsk_generic_xmit+0x51/0xb70
? _raw_spin_unlock_irqrestore+0xe/0x40
xsk_sendmsg+0xda/0x1c0
__sys_sendto+0x1ee/0x200
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x84/0x2f0
? __pfx_pollwake+0x10/0x10
? __rseq_handle_notify_resume+0xad/0x4c0
? restore_fpregs_from_fpstate+0x3c/0x90
? switch_fpu_return+0x5b/0xe0
? do_syscall_64+0x204/0x2f0
? do_syscall_64+0x204/0x2f0
? do_syscall_64+0x204/0x2f0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
</TASK>
[...]
Kernel panic - not syncing: Fatal exception in interrupt
Kernel Offset: 0x1c000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
Instead use the skb destructor_arg pointer along with pointer tagging.
As pointers are always aligned to 8B, use the bottom bit to indicate
whether this a single address or an allocated struct containing several
addresses.
Fixes: 30f241fcf5 ("xsk: Fix immature cq descriptor production")
Closes: https://lore.kernel.org/netdev/0435b904-f44f-48f8-afb0-68868474bf1c@nop.hu/
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://patch.msgid.link/20251124171409.3845-1-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There have been reports that RTL8127 hangs on suspend and shutdown,
partially disappearing from lspci until power-cycling.
According to Realtek disabling PLL's when switching to D3 should be
avoided on that chip version. Fix this by aligning disabling PLL's
with the vendor drivers, what in addition results in PLL's not being
disabled when switching to D3hot on other chip versions.
Fixes: f24f7b2f3a ("r8169: add support for RTL8127A")
Tested-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/d7faae7e-66bc-404a-a432-3a496600575f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when skb is null, the driver prints an error and then
dereferences skb on the next line.
To fix this, let's add a 'break' after the error message to switch
to sxgbe_rx_refill(), which is similar to the approach taken by the
other drivers in this particular case, e.g. calxeda with xgmac_rx().
Found during a code review.
Fixes: 1edb9ca69e ("net: sxgbe: add basic framework for Samsung 10Gb ethernet driver")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251121123834.97748-1-aleksei.kodanev@bell-sw.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Attempting to add a port device that is already up will expectedly fail,
but not before modifying the team device header_ops.
In the case of the syzbot reproducer the gre0 device is
already in state UP when it attempts to add it as a
port device of team0, this fails but before that
header_ops->create of team0 is changed from eth_header to ipgre_header
in the call to team_dev_type_check_change.
Later when we end up in ipgre_header() struct ip_tunnel* points to nonsense
as the private data of the device still holds a struct team.
Example sequence of iproute2 commands to reproduce the hang/BUG():
ip link add dev team0 type team
ip link add dev gre0 type gre
ip link set dev gre0 up
ip link set dev gre0 master team0
ip link set dev team0 up
ping -I team0 1.1.1.1
Move team_dev_type_check_change down where all other checks have passed
as it changes the dev type with no way to restore it in case
one of the checks that follow it fail.
Also make sure to preserve the origial mtu assignment:
- If port_dev is not the same type as dev, dev takes mtu from port_dev
- If port_dev is the same type as dev, port_dev takes mtu from dev
This is done by adding a conditional before the call to dev_set_mtu
to prevent it from assigning port_dev->mtu = dev->mtu and instead
letting team_dev_type_check_change assign dev->mtu = port_dev->mtu.
The conditional is needed because the patch moves the call to
team_dev_type_check_change past dev_set_mtu.
Testing:
- team device driver in-tree selftests
- Add/remove various devices as slaves of team device
- syzbot
Reported-by: syzbot+a2a3b519de727b0f7903@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=a2a3b519de727b0f7903
Fixes: 1d76efe157 ("team: add support for non-ethernet devices")
Signed-off-by: Nikola Z. Ivanov <zlatistiv@gmail.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20251122002027.695151-1-zlatistiv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rate limiting validation condition currently checks the output
variable max_bw_value[i] instead of the input value
maxrate->tc_maxrate[i]. This causes the validation to compare an
uninitialized or stale value rather than the actual requested rate.
The condition should check the input rate to properly validate against
the upper limit:
} else if (maxrate->tc_maxrate[i] <= upper_limit_gbps) {
This aligns with the pattern used in the first branch, which correctly
checks maxrate->tc_maxrate[i] against upper_limit_mbps.
The current implementation can lead to unreliable validation behavior:
- For rates between 25.5 Gbps and 255 Gbps, if max_bw_value[i] is 0
from initialization, the GBPS path may be taken regardless of whether
the actual rate is within bounds
- When processing multiple TCs (i > 0), max_bw_value[i] contains the
value computed for the previous TC, affecting the validation logic
- The overflow check for rates exceeding 255 Gbps may not trigger
consistently depending on previous array values
This patch ensures the validation correctly examines the requested rate
value for proper bounds checking.
Fixes: 43b27d1bd8 ("net/mlx5e: Fix wraparound in rate limiting for values above 255 Gbps")
Signed-off-by: Danielle Costantino <dcostantino@meta.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20251124180043.2314428-1-dcostantino@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To initialize the taprio block in lan966x, it is required to configure
the register REVISIT_DLY. The purpose of this register is to set the
delay before revisit the next gate and the value of this register depends
on the system clock. The problem is that the we calculated wrong the value
of the system clock period in picoseconds. The actual system clock is
~165.617754MHZ and this correspond to a period of 6038 pico seconds and
not 15125 as currently set.
Fixes: e462b27173 ("net: lan966x: Add offload support for taprio")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251121061411.810571-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
gpy_update_interface() returns early in case the PHY is internal or
connected via USXGMII. In this case the gigabit master/slave property
as well as MDI/MDI-X status also won't be read which seems wrong.
Always read those properties by moving the logic to retrieve them to
gpy_read_status().
Fixes: fd8825cd8c ("net: phy: mxl-gpy: Add PHY Auto/MDI/MDI-X set driver for GPY211 chips")
Fixes: 311abcdddc ("net: phy: add support to get Master-Slave configuration")
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/71fccf3f56742116eb18cc070d2a9810479ea7f9.1763650701.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Protect access to fore200e->available_cell_rate with rate_mtx lock in the
error handling path of fore200e_open() to prevent a data race.
The field fore200e->available_cell_rate is a shared resource used to track
available bandwidth. It is concurrently accessed by fore200e_open(),
fore200e_close(), and fore200e_change_qos().
In fore200e_open(), the lock rate_mtx is correctly held when subtracting
vcc->qos.txtp.max_pcr from available_cell_rate to reserve bandwidth.
However, if the subsequent call to fore200e_activate_vcin() fails, the
function restores the reserved bandwidth by adding back to
available_cell_rate without holding the lock.
This introduces a race condition because available_cell_rate is a global
device resource shared across all VCCs. If the error path in
fore200e_open() executes concurrently with operations like
fore200e_close() or fore200e_change_qos() on other VCCs, a
read-modify-write race occurs.
Specifically, the error path reads the rate without the lock. If another
CPU acquires the lock and modifies the rate (e.g., releasing bandwidth in
fore200e_close()) between this read and the subsequent write, the error
path will overwrite the concurrent update with a stale value. This results
in incorrect bandwidth accounting.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <hanguidong02@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251120120657.2462194-1-hanguidong02@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Bastien Curutchet says:
====================
net: dsa: microchip: Fix resource releases in error path
I worked on adding PTP support for the KSZ8463. While doing so, I ran
into a few bugs in the resource release process that occur when things go
wrong arount IRQ initialization.
This small series fixes those bugs.
The next series, which will add the PTP support, depend on this one.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
---
Bastien Curutchet (Schneider Electric) (5):
net: dsa: microchip: common: Fix checks on irq_find_mapping()
net: dsa: microchip: ptp: Fix checks on irq_find_mapping()
net: dsa: microchip: Don't free uninitialized ksz_irq
net: dsa: microchip: Free previously initialized ports on init failures
net: dsa: microchip: Fix symetry in ksz_ptp_msg_irq_{setup/free}()
drivers/net/dsa/microchip/ksz_common.c | 31 +++++++++++++++----------------
drivers/net/dsa/microchip/ksz_ptp.c | 22 +++++++++-------------
2 files changed, 24 insertions(+), 29 deletions(-)
---
base-commit: 09652e543e809c2369dca142fee5d9b05be9bdc7
change-id: 20251031-ksz-fix-db345df7635f
Best regards,
====================
Link: https://patch.msgid.link/20251120-ksz-fix-v6-0-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The IRQ numbers created through irq_create_mapping() are only assigned
to ptpmsg_irq[n].num at the end of the IRQ setup. So if an error occurs
between their creation and their assignment (for instance during the
request_threaded_irq() step), we enter the error path and fail to
release the newly created virtual IRQs because they aren't yet assigned
to ptpmsg_irq[n].num.
Move the mapping creation to ksz_ptp_msg_irq_setup() to ensure symetry
with what's released by ksz_ptp_msg_irq_free().
In the error path, move the irq_dispose_mapping to the out_ptp_msg label
so it will be called only on created IRQs.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b2 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-5-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If a port interrupt setup fails after at least one port has already been
successfully initialized, the gotos miss some resource releasing:
- the already initialized PTP IRQs aren't released
- the already initialized port IRQs aren't released if the failure
occurs in ksz_pirq_setup().
Merge 'out_girq' and 'out_ptpirq' into a single 'port_release' label.
Behind this label, use the reverse loop to release all IRQ resources
for all initialized ports.
Jump in the middle of the reverse loop if an error occurs in
ksz_ptp_irq_setup() to only release the port IRQ of the current
iteration.
Cc: stable@vger.kernel.org
Fixes: c9cd961c0d ("net: dsa: microchip: lan937x: add interrupt support for port phy link")
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-4-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If something goes wrong at setup, ksz_irq_free() can be called on
uninitialized ksz_irq (for example when ksz_ptp_irq_setup() fails). It
leads to freeing uninitialized IRQ numbers and/or domains.
Use dsa_switch_for_each_user_port_continue_reverse() in the error path
to iterate only over the fully initialized ports.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b2 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-3-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
irq_find_mapping() returns a positive IRQ number or 0 if no IRQ is found
but it never returns a negative value. However, during the PTP IRQ setup,
we verify that its returned value isn't negative.
Fix the irq_find_mapping() check to enter the error path when 0 is
returned. Return -EINVAL in such case.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b2 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-2-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
irq_find_mapping() returns a positive IRQ number or 0 if no IRQ is found
but it never returns a negative value. However, on each
irq_find_mapping() call, we verify that the returned value isn't
negative.
Fix the irq_find_mapping() checks to enter error paths when 0 is
returned. Return -EINVAL in such cases.
CC: stable@vger.kernel.org
Fixes: c9cd961c0d ("net: dsa: microchip: lan937x: add interrupt support for port phy link")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-1-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- hci_sock: Prevent race in socket write iter and sock bind
- hci_core: Fix triggering cmd_timer for HCI_OP_NOP
- hci_core: lookup hci_conn on RX path on protocol side
- SMP: Fix not generating mackey and ltk when repairing
- btusb: mediatek: Fix kernel crash when releasing mtk iso interface
- btusb: mediatek: Avoid btusb_mtk_claim_iso_intf() NULL deref
* tag 'for-net-2025-11-21' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: SMP: Fix not generating mackey and ltk when repairing
Bluetooth: btusb: mediatek: Avoid btusb_mtk_claim_iso_intf() NULL deref
Bluetooth: hci_core: lookup hci_conn on RX path on protocol side
Bluetooth: hci_sock: Prevent race in socket write iter and sock bind
Bluetooth: hci_core: Fix triggering cmd_timer for HCI_OP_NOP
Bluetooth: btusb: mediatek: Fix kernel crash when releasing mtk iso interface
====================
Link: https://patch.msgid.link/20251121145332.177015-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explain in commit fa349e396e ("veth: Fix race with AF_XDP exposing
old or uninitialized descriptors") for veth there is a chance after
napi_complete_done() that another CPU can manage start another NAPI
instance running veth_pool(). For NAPI this is correctly handled as the
napi_schedule_prep() check will prevent multiple instances from getting
scheduled, but for the remaining code in veth_pool() this can run
concurrent with the newly started NAPI instance.
The problem/race is that xdp_clear_return_frame_no_direct() isn't
designed to be nested.
Prior to commit 401cb7dae8 ("net: Reference bpf_redirect_info via
task_struct on PREEMPT_RT.") the temporary BPF net context
bpf_redirect_info was stored per CPU, where this wasn't an issue. Since
this commit the BPF context is stored in 'current' task_struct. When
running veth in threaded-NAPI mode, then the kthread becomes the storage
area. Now a race exists between two concurrent veth_pool() function calls
one exiting NAPI and one running new NAPI, both using the same BPF net
context.
Race is when another CPU gets within the xdp_set_return_frame_no_direct()
section before exiting veth_pool() calls the clear-function
xdp_clear_return_frame_no_direct().
Fixes: 401cb7dae8 ("net: Reference bpf_redirect_info via task_struct on PREEMPT_RT.")
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://patch.msgid.link/176356963888.337072.4805242001928705046.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In atm_init(), if atmsvc_init() fails, the code jumps to out_atmpvc_exit
label which incorrectly calls atmsvc_exit() instead of atmpvc_exit().
This results in calling the wrong cleanup function and failing to properly
clean up atmpvc_init().
Fix this by calling atmpvc_exit() in the out_atmpvc_exit error path.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Sayooj K Karun <sayooj@aerlync.com>
Link: https://patch.msgid.link/20251119085747.67139-1-sayooj@aerlync.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The change eed467b517 ("Bluetooth: fix passkey uninitialized when used")
introduced a goto that bypasses the creation of temporary mackey and ltk
which are later used by the likes of DHKey Check step.
Later ffee202a78 ("Bluetooth: Always request for user confirmation for
Just Works (LE SC)") which means confirm_hint is always set in case
JUST_WORKS so the branch checking for an existing LTK becomes pointless
as confirm_hint will always be set, so this just merge both cases of
malicious or legitimate devices to be confirmed before continuing with the
pairing procedure.
Link: https://github.com/bluez/bluez/issues/1622
Fixes: eed467b517 ("Bluetooth: fix passkey uninitialized when used")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In btusb_mtk_setup(), we set `btmtk_data->isopkt_intf` to:
usb_ifnum_to_if(data->udev, MTK_ISO_IFNUM)
That function can return NULL in some cases. Even when it returns
NULL, though, we still go on to call btusb_mtk_claim_iso_intf().
As of commit e9087e8288 ("Bluetooth: btusb: mediatek: Add locks for
usb_driver_claim_interface()"), calling btusb_mtk_claim_iso_intf()
when `btmtk_data->isopkt_intf` is NULL will cause a crash because
we'll end up passing a bad pointer to device_lock(). Prior to that
commit we'd pass the NULL pointer directly to
usb_driver_claim_interface() which would detect it and return an
error, which was handled.
Resolve the crash in btusb_mtk_claim_iso_intf() by adding a NULL check
at the start of the function. This makes the code handle a NULL
`btmtk_data->isopkt_intf` the same way it did before the problematic
commit (just with a slight change to the error message printed).
Reported-by: IncogCyberpunk <incogcyberpunk@proton.me>
Closes: http://lore.kernel.org/r/a380d061-479e-4713-bddd-1d6571ca7e86@leemhuis.info
Fixes: e9087e8288 ("Bluetooth: btusb: mediatek: Add locks for usb_driver_claim_interface()")
Cc: stable@vger.kernel.org
Tested-by: IncogCyberpunk <incogcyberpunk@proton.me>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The hdev lock/lookup/unlock/use pattern in the packet RX path doesn't
ensure hci_conn* is not concurrently modified/deleted. This locking
appears to be leftover from before conn_hash started using RCU
commit bf4c632524 ("Bluetooth: convert conn hash to RCU")
and not clear if it had purpose since then.
Currently, there are code paths that delete hci_conn* from elsewhere
than the ordered hdev->workqueue where the RX work runs in. E.g.
commit 5af1f84ed1 ("Bluetooth: hci_sync: Fix UAF on hci_abort_conn_sync")
introduced some of these, and there probably were a few others before
it. It's better to do the locking so that even if these run
concurrently no UAF is possible.
Move the lookup of hci_conn and associated socket-specific conn to
protocol recv handlers, and do them within a single critical section
to cover hci_conn* usage and lookup.
syzkaller has reported a crash that appears to be this issue:
[Task hdev->workqueue] [Task 2]
hci_disconnect_all_sync
l2cap_recv_acldata(hcon)
hci_conn_get(hcon)
hci_abort_conn_sync(hcon)
hci_dev_lock
hci_dev_lock
hci_conn_del(hcon)
v-------------------------------- hci_dev_unlock
hci_conn_put(hcon)
conn = hcon->l2cap_data (UAF)
Fixes: 5af1f84ed1 ("Bluetooth: hci_sync: Fix UAF on hci_abort_conn_sync")
Reported-by: syzbot+d32d77220b92eddd89ad@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=d32d77220b92eddd89ad
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There is a potential race condition between sock bind and socket write
iter. bind may free the same cmd via mgmt_pending before write iter sends
the cmd, just as syzbot reported in UAF[1].
Here we use hci_dev_lock to synchronize the two, thereby avoiding the
UAF mentioned in [1].
[1]
syzbot reported:
BUG: KASAN: slab-use-after-free in mgmt_pending_remove+0x3b/0x210 net/bluetooth/mgmt_util.c:316
Read of size 8 at addr ffff888077164818 by task syz.0.17/5989
Call Trace:
mgmt_pending_remove+0x3b/0x210 net/bluetooth/mgmt_util.c:316
set_link_security+0x5c2/0x710 net/bluetooth/mgmt.c:1918
hci_mgmt_cmd+0x9c9/0xef0 net/bluetooth/hci_sock.c:1719
hci_sock_sendmsg+0x6ca/0xef0 net/bluetooth/hci_sock.c:1839
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg+0x21c/0x270 net/socket.c:742
sock_write_iter+0x279/0x360 net/socket.c:1195
Allocated by task 5989:
mgmt_pending_add+0x35/0x140 net/bluetooth/mgmt_util.c:296
set_link_security+0x557/0x710 net/bluetooth/mgmt.c:1910
hci_mgmt_cmd+0x9c9/0xef0 net/bluetooth/hci_sock.c:1719
hci_sock_sendmsg+0x6ca/0xef0 net/bluetooth/hci_sock.c:1839
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg+0x21c/0x270 net/socket.c:742
sock_write_iter+0x279/0x360 net/socket.c:1195
Freed by task 5991:
mgmt_pending_free net/bluetooth/mgmt_util.c:311 [inline]
mgmt_pending_foreach+0x30d/0x380 net/bluetooth/mgmt_util.c:257
mgmt_index_removed+0x112/0x2f0 net/bluetooth/mgmt.c:9477
hci_sock_bind+0xbe9/0x1000 net/bluetooth/hci_sock.c:1314
Fixes: 6fe26f694c ("Bluetooth: MGMT: Protect mgmt_pending list with its own lock")
Reported-by: syzbot+9aa47cd4633a3cf92a80@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=9aa47cd4633a3cf92a80
Tested-by: syzbot+9aa47cd4633a3cf92a80@syzkaller.appspotmail.com
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
HCI_OP_NOP means no command was actually sent so there is no point in
triggering cmd_timer which may cause a hdev->reset in the process since
it is assumed that the controller is stuck processing a command.
Fixes: e2d471b780 ("Bluetooth: ISO: Fix not using SID from adv report")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Pull networking fixes from Jakub Kicinski:
"Including fixes from IPsec and wireless.
Previous releases - regressions:
- prevent NULL deref in generic_hwtstamp_ioctl_lower(),
newer APIs don't populate all the pointers in the request
- phylink: add missing supported link modes for the fixed-link
- mptcp: fix false positive warning in mptcp_pm_nl_rm_addr
Previous releases - always broken:
- openvswitch: remove never-working support for setting NSH fields
- xfrm: number of fixes for error paths of xfrm_state creation/
modification/deletion
- xfrm: fixes for offload
- fix the determination of the protocol of the inner packet
- don't push locally generated packets directly to L2 tunnel
mode offloading, they still need processing from the standard
xfrm path
- mptcp: fix a couple of corner cases in fallback and fastclose
handling
- wifi: rtw89: hw_scan: prevent connections from getting stuck,
work around apparent bug in FW by tweaking messages we send
- af_unix: fix duplicate data if PEEK w/ peek_offset needs to wait
- veth: more robust handing of race to avoid txq getting stuck
- eth: ps3_gelic_net: handle skb allocation failures"
* tag 'net-6.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits)
vsock: Ignore signal/timeout on connect() if already established
be2net: pass wrb_params in case of OS2BMC
l2tp: reset skb control buffer on xmit
net: dsa: microchip: lan937x: Fix RGMII delay tuning
selftests: mptcp: add a check for 'add_addr_accepted'
mptcp: fix address removal logic in mptcp_pm_nl_rm_addr
selftests: mptcp: join: userspace: longer timeout
selftests: mptcp: join: endpoints: longer timeout
selftests: mptcp: join: fastclose: remove flaky marks
mptcp: fix duplicate reset on fastclose
mptcp: decouple mptcp fastclose from tcp close
mptcp: do not fallback when OoO is present
mptcp: fix premature close in case of fallback
mptcp: avoid unneeded subflow-level drops
mptcp: fix ack generation for fallback msk
wifi: rtw89: hw_scan: Don't let the operating channel be last
net: phylink: add missing supported link modes for the fixed-link
selftest: af_unix: Add test for SO_PEEK_OFF.
af_unix: Read sk_peek_offset() again after sleeping in unix_stream_read_generic().
net/mlx5: Clean up only new IRQ glue on request_irq() failure
...
be_insert_vlan_in_pkt() is called with the wrb_params argument being NULL
at be_send_pkt_to_bmc() call site. This may lead to dereferencing a NULL
pointer when processing a workaround for specific packet, as commit
bc0c3405ab ("be2net: fix a Tx stall bug caused by a specific ipv6
packet") states.
The correct way would be to pass the wrb_params from be_xmit().
Fixes: 760c295e0e ("be2net: Support for OS2BMC.")
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Vatoropin <a.vatoropin@crpt.ru>
Link: https://patch.msgid.link/20251119105015.194501-1-a.vatoropin@crpt.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The L2TP stack did not reset the skb control buffer before sending the
encapsulated package.
In a setup with an ath10k radio and batman-adv over an L2TP tunnel
massive fragmentations happen sporadically if the L2TP tunnel is
established over IPv4.
L2TP might reset some of the fields in the IP control buffer, but L2TP
assumes the type of the control buffer to be of an IPv4 packet.
In case the L2TP interface is used as a batadv hardif or the packet is
an IPv6 packet, this assumption breaks.
Clear the entire control buffer to avoid such mishaps altogether.
Fixes: f77ae93904 ("[PPPOL2TP]: Reset meta-data in xmit function")
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://patch.msgid.link/20251118001619.242107-1-mail@david-bauer.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima
Paolo Abeni
Wei Fang
Jeremy Kerr
Jakub Kicinski
Jiefeng Zhang
Jon Kohler
Mohsin Bashir
Vladimir Oltean
Alexandra Winter
Slark Xiao
Jason Wang
Shaurya Rane
Biju Das
Fernando Fernandez Mancera
Heiner Kallweit
Alexey Kodanev
Nikola Z. Ivanov
Danielle Costantino
Horatiu Vultur
Daniel Golle
Gui-Dong Han
Bastien Curutchet (Schneider Electric)
Kai-Heng Feng
Eric Dumazet
Jesper Dangaard Brouer
Sayooj K Karun
Luiz Augusto von Dentz
Douglas Anderson
Pauli Virtanen
Edward Adam Davis
Chris Lu
Linus Torvalds
Michal Luczaj
Andrey Vatoropin
David Bauer