The mute and mic-mute LEDs on HP ENVY x360 Convertible 15-es0xxx
(PCI SSID 103c:88b3) do not work with the current driver.
This model requires a combination of COEFBIT and GPIO fixups to
correctly control the LEDs. Introduce a new fixup function
alc245_fixup_hp_envy_x360_mute_led and add a quirk to apply it.
Signed-off-by: Illia Barbashyn <04baril@gmail.com>
Link: https://patch.msgid.link/20260207221955.24132-1-04baril@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
First, adding a generic quirk for Bass speaker DAC avoidance.
This pattern (re-routing the bass speakers off of a DAC without volume
control) seems common enough that having a "model" to match against and
quickly use to verify may be worthwhile.
The alc285_fixup_thinkpad_x1_gen7 routing was selected, amongst the
different options, as it should allow tuning the ratio between both
speaker set.
The routing was verified using `hda-verb`, and picking either 0x00 or
0x01. Either routing made the volume of the bass speakers controllable.
hda-verb /dev/snd/hwC1D0 0x17 SET_CONNECT_SEL 0x01
This likely will apply for the Minisforum V3, though there isn't a lot
of information to confirm whether or not the identifiers are the same.
This was verified on the Minisforum V3 SE, and the root cause (the bass
speakers routing) was found out by using pink noise, and playing with
the mixers.
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Link: https://patch.msgid.link/20260203010132.1981419-2-samuel@dionne-riel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add mixer control support for the Focusrite Forte (USB ID 0x1235:0x8010),
an older USB audio interface that predates the Scarlett 2nd generation.
The Forte uses UAC2_CS_MEM (bRequest=0x03) for its input controls rather
than the standard UAC2_CS_CUR (0x01) used by Scarlett devices. This patch
adds Forte-specific control handlers that use the correct USB protocol.
Features implemented:
- Input source selection (Mic/Line/Inst) for both channels
- High pass filter switch
- 48V phantom power switch
- Phase invert switch
- Pad switch
- Preamp gain control (0-42 range, ~0-75dB)
- Matrix mixer controls (6 inputs x 4 outputs)
- Output volume and mute controls
The device is registered via mixer_quirks.c and uses the existing
mixer_scarlett.c infrastructure with Forte-specific additions.
Credit: This work builds on prior reverse-engineering by alastair-dm.
Link: https://github.com/alastair-dm/forte-mixer/wiki
Link: https://github.com/alastair-dm/forte-mixer
Link: https://github.com/jopdorp/forte-mixer
Signed-off-by: Jegor van Opdorp <jegorvanopdorp@gmail.com>
Link: https://patch.msgid.link/20260127081541.219669-1-jegorvanopdorp@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If appending " Jack" is not necessary, replace snprintf("%s", ...) with
the faster strscpy().
Additionally, rename 'need_cat' to the clearer 'append_suf', use local
variables for the suffix and its length, remove the confusing comment,
compare strncmp() to 0, and use 'size_t' for the 'size' function
parameter.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Link: https://patch.msgid.link/20260125155159.98720-1-thorsten.blum@linux.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The LG Gram Style 14 (14Z90RS-G.AD77F, SSID 1854:0490) with Realtek ALC298
shows normal routing and volume changes, but internal speakers stay silent
unless a userland HDA-verb workaround is applied.
Add a dedicated quirk for the LG Gram Style 14 that programs the codec
coefficient sequence used by the known workaround and enables the speaker
amps only during playback.
Tested-by: Damien Dagorn <damien.dagorn29@gmail.com>
Signed-off-by: Damien Dagorn <damien.dagorn29@gmail.com>
Link: https://lore.kernel.org/CAN59QMUhd4kHrkRoJA6VzEr2VKezN2yjHnANaQoZn2-Bnwe3bQ@mail.gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC: Fixes for v6.19
A moderately large collection of fixes since I missed a week, plus a few
new device IDs and quirks. It's all fairly minor, including a bunch of
work on the device tree bindings fixes which have no runtime effect.
There's one SoundWire change here exporting a symbol which was required
for a fix to the ASoC SoundWire code.
Merge patches that Pengutronix have been carrying in their tree for a
while and were upstreamed by Sascha Hauer together with some new
features that are going into the next release.
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
This series fixes a problem with soc_sdw_utils.c calling the wrong
codec init callbacks, because it assumed that the DAI name could be
used to uniquely identify the codec. This isn't the case, especially
on SDCA which is a generic driver for many parts.
The first patch is needed to add a missing export to SoundWire core.
The CS42L43 codec's load detection can return different impedance values
that map to either HEADPHONE or LINEOUT jack types. However, the
soc_jack_pins array only maps SND_JACK_HEADPHONE to the "Headphone" DAPM
pin, not SND_JACK_LINEOUT.
When headphones are detected with an impedance that maps to LINEOUT
(such as impedance value 0x2), the driver reports SND_JACK_LINEOUT.
Since this doesn't match the jack pin mask, the "Headphone" DAPM pin
is not activated, and no audio is routed to the headphone outputs.
Fix by adding SND_JACK_LINEOUT to the Headphone pin mask, so that both
headphone and line-out detection properly enable the headphone output
path.
This fixes no audio output on devices like the Lenovo ThinkPad P16 Gen 3
where headphones are detected with LINEOUT impedance.
Fixes: d74bad3b74 ("ASoC: intel: sof_sdw_cs42l43: Create separate jacks for hp and mic")
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Cole Leavitt <cole@unwrap.rs>
Link: https://patch.msgid.link/20260114025518.28519-1-cole@unwrap.rs
Signed-off-by: Mark Brown <broonie@kernel.org>
asoc_sdw_rtd_init() needs to call the rtd_init() callbacks for each
codec in a dailink. It was finding the codecs by looking for the
matching DAI name in codec_info_list[] but this isn't correct, because
the DAI name isn't guaranteed to be unique. Parts using the same codec
driver (so the same DAI names) might require different machine driver
setup.
Instead, get the struct sdw_slave and extract the SoundWire part ID.
Use this to lookup the entry in codec_info_list[]. This is the same
identity info that was used to find the entry when the machine driver
created the dailink.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e377c94773 ("ASoC: intel/sdw_utils: move soundwire codec_info_list structure")
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260112140758.215799-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Jon Hunter <jonathanh@nvidia.com>:
This series includes fixes for the realtek,rt5640 dt-binding to address
a few warnings that are observed when running the CHECK_DTBS=y for some
DTBs that use this codec.
In this case, the user constructed the parameters with maxpacksize 40
for rate 22050 / pps 1000, and packsize[0] 22 packsize[1] 23. The buffer
size for each data URB is maxpacksize * packets, which in this example
is 40 * 6 = 240; When the user performs a write operation to send audio
data into the ALSA PCM playback stream, the calculated number of frames
is packsize[0] * packets = 264, which exceeds the allocated URB buffer
size, triggering the out-of-bounds (OOB) issue reported by syzbot [1].
Added a check for the number of single data URB frames when calculating
the number of frames to prevent [1].
[1]
BUG: KASAN: slab-out-of-bounds in copy_to_urb+0x261/0x460 sound/usb/pcm.c:1487
Write of size 264 at addr ffff88804337e800 by task syz.0.17/5506
Call Trace:
copy_to_urb+0x261/0x460 sound/usb/pcm.c:1487
prepare_playback_urb+0x953/0x13d0 sound/usb/pcm.c:1611
prepare_outbound_urb+0x377/0xc50 sound/usb/endpoint.c:333
Reported-by: syzbot+6db0415d6d5c635f72cb@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=6db0415d6d5c635f72cb
Tested-by: syzbot+6db0415d6d5c635f72cb@syzkaller.appspotmail.com
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Link: https://patch.msgid.link/tencent_9AECE6CD2C7A826D902D696C289724E8120A@qq.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set gpiochip parent to the struct device of the dummy GPIO driver
so that the software node will be associated with the GPIO chip.
The recent commit e5d527be7e ("gpio: swnode: don't use the
swnode's name as the key for GPIO lookup") broke cirrus_scodec_test,
because the software node no longer gets associated with the GPIO
driver by name.
Instead, setting struct gpio_chip.parent to the owning struct device
will find the node using a normal fwnode lookup.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2144833e7b ("ALSA: hda: cirrus_scodec: Add KUnit test")
Link: https://patch.msgid.link/20260113130954.574670-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds quirkiness for the Cirrus Logic CDB35L56-FOUR-HD board.
The quirk must be forced by model name "CDB35L56-FOUR-HD"
because there isn't a unique SSID that can be used. For example
in /etc/modprobe.d:
options snd-hda-intel model="CDB35L56-FOUR-HD"
The CDB35L56-FOUR-HD is not a complete PC. It is an add-on audio
board that requires a host system and replaces the normal HDA codec
on the host. Because of this there isn't an SSID that uniquely
identifies this configuration. Also, the usual host board is an
Aaeon UpXtreme, which doesn't have a unique SSID.
Because of this, the quirk must be forced by a module param.
This is acceptable because it is a development board, not an
end-user system, so there is no need for it to be detected
automatically.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Co-developed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260112142850.243054-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just like GA403U, this GA403W needs to remap woofers to DAC1. Similarly to
other Asus devices, headphones/headset MIC is not working, however the pin
config alone is not enough to fix it.
From Windows dump of GA403W:
0x12, 0x90a60140 # Correctly set by codec out of the box
0x13, 0x90a60550
0x14, 0x90170510
0x17, 0x90170120 # Correctly set by codec out of the box
0x19, 0x03a11050 # Set by ALC285_FIXUP_ASUS_GA403U_HEADSET_MIC
0x1a, 0x411115F0
0x1b, 0x03a11c30 # Set by ALC285_FIXUP_ASUS_GA403U_HEADSET_MIC
0x1d, 0x40663A45 # Correctly set by codec out of the box
0x21, 0x03211430
Even with all the values set, MIC of the jack is not detected. Until a
complete solution is found, set ALC285_FIXUP_ASUS_GA403U_HEADSET_MIC
for GA403W which fixes audio volume control for woofers. No need to
create new quirk with missing pin config just yet, since its not
making the situation better.
Signed-off-by: Aleksandrs Vinarskis <alex@vinarskis.com>
Link: https://patch.msgid.link/20260112-asus-rog-audio-v1-1-513957b4704e@vinarskis.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 4d4021b0bb ("ASoC: tegra: Fix uninitialized flat cache warning
in tegra210_ahub") attempted to fix the uninitialized flat cache warning
that is observed for the Tegra210 AHUB driver. However, the change broke
various audio tests because an -EBUSY error is returned when accessing
registers from cache before they are read from hardware. Revert this
change for now, until a proper fix is available.
Fixes: 4d4021b0bb ("ASoC: tegra: Fix uninitialized flat cache warning in tegra210_ahub")
Signed-off-by: sheetal <sheetal@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20251217132524.2844499-1-sheetal@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull crypto library fixes from Eric Biggers:
- A couple more fixes for the lib/crypto KUnit tests
- Fix missing MMU protection for the AES S-box
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto: aes: Fix missing MMU protection for AES S-box
MAINTAINERS: add test vector generation scripts to "CRYPTO LIBRARY"
lib/crypto: tests: Fix syntax error for old python versions
lib/crypto: tests: polyval_kunit: Increase iterations for preparekey in IRQs
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc driver fixes for some reported issues.
Included in here is:
- much reported rust_binder fix
- counter driver fixes
- new device ids for the mei driver
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
rust_binder: remove spin_lock() in rust_shrink_free_page()
mei: me: add nova lake point S DID
counter: 104-quad-8: Fix incorrect return value in IRQ handler
counter: interrupt-cnt: Drop IRQF_NO_THREAD flag
Pull x86 fix from Ingo Molnar:
"Disable GCOV instrumentation in the SEV noinstr.c collection of SEV
noinstr methods, to further robustify the code"
* tag 'x86-urgent-2026-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/sev: Disable GCOV on noinstr object
Pull scheduler fix from Ingo Molnar:
"Fix a crash in sched_mm_cid_after_execve()"
* tag 'sched-urgent-2026-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/mm_cid: Prevent NULL mm dereference in sched_mm_cid_after_execve()
Pull misc irqchip fixes from Ingo Molnar:
- Fix an endianness bug in the gic-v5 irqchip driver
- Revert a broken commit from the riscv-imsic irqchip driver
* tag 'irq-urgent-2026-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "irqchip/riscv-imsic: Embed the vector array in lpriv"
irqchip/gic-v5: Fix gicv5_its_map_event() ITTE read endianness
In a vain attempt to consolidate the email zoo switch everything to the
kernel.org account.
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull RISC-V fixes from Paul Walmsley:
"Notable changes include a fix to close one common microarchitectural
attack vector for out-of-order cores. Another patch exposed an
omission in my boot test coverage, which is currently missing
relocatable kernels. Otherwise, the fixes seem to be settling down for
us.
- Fix CONFIG_RELOCATABLE=y boots by building Image files from
vmlinux, rather than vmlinux.unstripped, now that the .modinfo
section is included in vmlinux.unstripped
- Prevent branch predictor poisoning microarchitectural attacks that
use the syscall index as a vector by using array_index_nospec() to
clamp the index after the bounds check (as x86 and ARM64 already
do)
- Fix a crash in test_kprobes when building with Clang
- Fix a deadlock possible when tracing is enabled for SBI ecalls
- Fix the definition of the Zk standard RISC-V ISA extension bundle,
which was missing the Zknh extension
- A few other miscellaneous non-functional cleanups, removing unused
macros, fixing an out-of-date path in code comments, resolving a
compile-time warning for a type mismatch in a pr_crit(), and
removing an unnecessary header file inclusion"
* tag 'riscv-for-linus-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: trace: fix snapshot deadlock with sbi ecall
riscv: remove irqflags.h inclusion in asm/bitops.h
riscv: cpu_ops_sbi: smp_processor_id() returns int, not unsigned int
riscv: configs: Clean up references to non-existing configs
riscv: kexec_image: Fix dead link to boot-image-header.rst
riscv: pgtable: Cleanup useless VA_USER_XXX definitions
riscv: cpufeature: Fix Zk bundled extension missing Zknh
riscv: fix KUnit test_kprobes crash when building with Clang
riscv: Sanitize syscall table indexing under speculation
riscv: boot: Always make Image from vmlinux, not vmlinux.unstripped
Pull driver core fixes from Danilo Krummrich:
- Fix swapped example values for the `family` and `machine` attributes
in the sysfs SoC bus ABI documentation
- Fix Rust build and intra-doc issues when optional subsystems
(CONFIG_PCI, CONFIG_AUXILIARY_BUS, CONFIG_PRINTK) are disabled
- Fix typos and incorrect safety comments in Rust PCI, DMA, and
device ID documentation
* tag 'driver-core-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core:
rust: device: Remove explicit import of CStrExt
rust: pci: fix typos in Bar struct's comments
rust: device: fix broken intra-doc links
rust: dma: fix broken intra-doc links
rust: driver: fix broken intra-doc links to example driver types
rust: device_id: replace incorrect word in safety documentation
rust: dma: remove incorrect safety documentation
docs: ABI: sysfs-devices-soc: Fix swapped sample values
Pedro Amarante
Illia Barbashyn
Takashi Iwai
Dan Carpenter
Samuel Dionne-Riel
Jegor van Opdorp
gongqi
Shenghao Ding
Thorsten Blum
Damien Dagorn
Richard Fitzgerald
Mark Brown
Zhang Heng
Emil Svendsen
Dimitrios Katsaros
Cole Leavitt
fenugrec
Edward Adam Davis
Bharat Dev Burman
Simon Trimmer
Aleksandrs Vinarskis
Radhi Bajahaw
sheetal
Rob Herring (Arm)
Linus Torvalds
Thomas Gleixner