commit 83dbf898a2 upstream.
Masking all unused MSI-X entries is done to ensure that a crash kernel
starts from a clean slate, which correponds to the reset state of the
device as defined in the PCI-E specificion 3.0 and later:
Vector Control for MSI-X Table Entries
--------------------------------------
"00: Mask bit: When this bit is set, the function is prohibited from
sending a message using this MSI-X Table entry.
...
This bit’s state after reset is 1 (entry is masked)."
A Marvell NVME device fails to deliver MSI interrupts after trying to
enable MSI-X interrupts due to that masking. It seems to take the MSI-X
mask bits into account even when MSI-X is disabled.
While not specification compliant, this can be cured by moving the masking
into the success path, so that the MSI-X table entries stay in device reset
state when the MSI-X setup fails.
[ tglx: Move it into the success path, add comment and amend changelog ]
Fixes: aa8092c1d1 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211210161025.3287927-1-sr@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fac6bf87c5 upstream.
When activate_stm_id_vb_detection is enabled, ID and Vbus detection relies
on sensing comparators. This detection needs time to stabilize.
A delay was already applied in dwc2_resume() when reactivating the
detection, but it wasn't done in dwc2_probe().
This patch adds delay after enabling STM ID/VBUS detection. Then, ID state
is good when initializing gadget and host, and avoid to get a wrong
Connector ID Status Change interrupt.
Fixes: a415083a11 ("usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS")
Cc: stable <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207124510.268841-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1aa2abb33a ]
The ability to write to MSR_IA32_PERF_CAPABILITIES from the host should
not depend on guest visible CPUID entries, even if just to allow
creating/restoring guest MSRs and CPUIDs in any sequence.
Fixes: 27461da310 ("KVM: x86/pmu: Support full width counting")
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211216165213.338923-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f08adf5add ]
Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value. Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.
Fix that up by only checking the single bit.
Fixes: 153a2d7e33 ("USB: gadget: detect too-big endpoint 0 requests")
Cc: Felipe Balbi <balbi@kernel.org>
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20211214184621.385828-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2fcbf81c3 ]
The libbpf CI reported occasional failure in btf_skc_cls_ingress:
test_syncookie:FAIL:Unexpected syncookie states gen_cookie:80326634 recv_cookie:0
bpf prog error at line 97
"error at line 97" means the bpf prog cannot find the listening socket
when the final ack is received. It then skipped processing
the syncookie in the final ack which then led to "recv_cookie:0".
The problem is the userspace program did not do accept() and went
ahead to close(listen_fd) before the kernel (and the bpf prog) had
a chance to process the final ack.
The fix is to add accept() call so that the userspace will wait for
the kernel to finish processing the final ack first before close()-ing
everything.
Fixes: 9a856cae22 ("bpf: selftest: Add test_btf_skc_cls_ingress")
Reported-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211216191630.466151-1-kafai@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 433956e912 ]
The prog - start_of_ldx is the offset before the faulting ldx to the location
after it, so this will be used to adjust pt_regs->ip for jumping over it and
continuing, and with old temp it would have been fixed up to the wrong offset,
causing crash.
Fixes: 4c5de12759 ("bpf: Emit explicit NULL pointer checks for PROBE_LDX instructions.")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c5d89bc10 ]
Since commit ac10be5cdb ("arm64: Use common
of_kexec_alloc_and_setup_fdt()"), smatch reports the following warning:
arch/arm64/kernel/machine_kexec_file.c:152 load_other_segments()
warn: missing error code 'ret'
Return code is not set to an error code in load_other_segments() when
of_kexec_alloc_and_setup_fdt() call returns a NULL dtb. This results
in status success (return code set to 0) being returned from
load_other_segments().
Set return code to -EINVAL if of_kexec_alloc_and_setup_fdt() returns
NULL dtb.
Signed-off-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: ac10be5cdb ("arm64: Use common of_kexec_alloc_and_setup_fdt()")
Link: https://lore.kernel.org/r/20211210010121.101823-1-nramas@linux.microsoft.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b8e6e7824 ]
The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.
This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.
The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.
The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211215202450.4086240-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c15b3123f ]
In nginx/wrk benchmark, there's a hung problem with high probability
on case likes that: (client will last several minutes to exit)
server: smc_run nginx
client: smc_run wrk -c 10000 -t 1 http://server
Client hangs with the following backtrace:
0 [ffffa7ce8Of3bbf8] __schedule at ffffffff9f9eOd5f
1 [ffffa7ce8Of3bc88] schedule at ffffffff9f9eløe6
2 [ffffa7ce8Of3bcaO] schedule_timeout at ffffffff9f9e3f3c
3 [ffffa7ce8Of3bd2O] wait_for_common at ffffffff9f9el9de
4 [ffffa7ce8Of3bd8O] __flush_work at ffffffff9fOfeOl3
5 [ffffa7ce8øf3bdfO] smc_release at ffffffffcO697d24 [smc]
6 [ffffa7ce8Of3be2O] __sock_release at ffffffff9f8O2e2d
7 [ffffa7ce8Of3be4ø] sock_close at ffffffff9f8ø2ebl
8 [ffffa7ce8øf3be48] __fput at ffffffff9f334f93
9 [ffffa7ce8Of3be78] task_work_run at ffffffff9flOlff5
10 [ffffa7ce8Of3beaO] do_exit at ffffffff9fOe5Ol2
11 [ffffa7ce8Of3bflO] do_group_exit at ffffffff9fOe592a
12 [ffffa7ce8Of3bf38] __x64_sys_exit_group at ffffffff9fOe5994
13 [ffffa7ce8Of3bf4O] do_syscall_64 at ffffffff9f9d4373
14 [ffffa7ce8Of3bfsO] entry_SYSCALL_64_after_hwframe at ffffffff9fa0007c
This issue dues to flush_work(), which is used to wait for
smc_connect_work() to finish in smc_release(). Once lots of
smc_connect_work() was pending or all executing work dangling,
smc_release() has to block until one worker comes to free, which
is equivalent to wait another smc_connnect_work() to finish.
In order to fix this, There are two changes:
1. For those idle smc_connect_work(), cancel it from the workqueue; for
executing smc_connect_work(), waiting for it to finish. For that
purpose, replace flush_work() with cancel_work_sync().
2. Since smc_connect() hold a reference for passive closing, if
smc_connect_work() has been cancelled, release the reference.
Fixes: 24ac3a08e6 ("net/smc: rebuild nonblocking connect")
Reported-by: Tony Lu <tonylu@linux.alibaba.com>
Tested-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/1639571361-101128-1-git-send-email-alibuda@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a03ef676a ]
When printing netdev features %pNF already takes care of the 0x prefix,
remove the explicit one.
Fixes: 6413139dfc ("skbuff: increase verbosity when dumping skb data")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e08cdf6304 ]
Debug print uses invalid check to detect if speed is unforced:
(speed != SPEED_UNFORCED) should be used instead of (!speed).
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Andrey Eremeev <Axtone4all@yandex.ru>
Fixes: 96a2b40c7b ("net: dsa: mv88e6xxx: add port's MAC speed setter")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 407ecd1bd7 ]
The return value of kmalloc() needs to be checked.
To avoid use in efx_nic_update_stats() in case of the failure of alloc.
Fixes: b593b6f1b4 ("sfc_ef100: statistics gathering")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0546b224cc ]
KASAN reports an out-of-bounds read in rk_gmac_setup on the line:
while (ops->regs[i]) {
This happens for most platforms since the regs flexible array member is
empty, so the memory after the ops structure is being read here. It
seems that mostly this happens to contain zero anyway, so we get lucky
and everything still works.
To avoid adding redundant data to nearly all the ops structures, add a
new flag to indicate whether the regs field is valid and avoid this loop
when it is not.
Fixes: 3bb3d6b1c1 ("net: stmmac: Add RK3566/RK3568 SoC support")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 481221775d ]
Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
since it may cause a potential kernel information leak issue, as follows:
1. nsim_bpf_map_alloc calls nsim_map_alloc_elem to allocate elements for
a new map.
2. nsim_map_alloc_elem uses kmalloc to allocate map's value, but doesn't
zero it.
3. A user application can use IOCTL BPF_MAP_LOOKUP_ELEM to get specific
element's information in the map.
4. The kernel function map_lookup_elem will call bpf_map_copy_value to get
the information allocated at step-2, then use copy_to_user to copy to the
user buffer.
This can only leak information for an array map.
Fixes: 395cacb5f1 ("netdevsim: bpf: support fake map offload")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Haimin Zhang <tcs.kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215111530.72103-1-tcs.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf0a375055 ]
The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.
This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.
Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:
* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
(the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17
Fixes: e84db72727 ("ixgbe: Introduce function to control MDIO speed")
Signed-off-by: Cyril Novikov <cnovikov@lynx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 271225fd57 ]
Commit a296d665ea ("ixgbe: Add ethtool support to enable 2.5 and 5.0
Gbps support") introduced suppression of the advertisement of NBASE-T
speeds by default, according to Todd Fujinaka to accommodate customers
with network switches which could not cope with advertised NBASE-T
speeds, as posted in the E1000-devel mailing list:
https://sourceforge.net/p/e1000/mailman/message/37106269/
However, the suppression was not documented at all, nor was how to
enable NBASE-T support.
Properly document the NBASE-T suppression and how to enable NBASE-T
support.
Fixes: a296d665ea ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support")
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0182d1f3fa ]
The LTR maximum value was incorrectly written using the scale from
the LTR minimum value. This would cause incorrect values to be sent,
in cases where the initial calculation lead to different min/max scales.
Fixes: 707abf0695 ("igc: Add initial LTR support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6d335a60d ]
In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.
In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.
The KASAN logs are as follows:
[ 35.126075] BUG: KASAN: use-after-free in free_netdev+0x1fd/0x450
[ 35.127170] Read of size 8 at addr ffff88810126d990 by task modprobe/366
[ 35.128360]
[ 35.128643] CPU: 1 PID: 366 Comm: modprobe Not tainted 5.15.0-rc2+ #14
[ 35.129789] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[ 35.131749] Call Trace:
[ 35.132199] dump_stack_lvl+0x59/0x7b
[ 35.132865] print_address_description+0x7c/0x3b0
[ 35.133707] ? free_netdev+0x1fd/0x450
[ 35.134378] __kasan_report+0x160/0x1c0
[ 35.135063] ? free_netdev+0x1fd/0x450
[ 35.135738] kasan_report+0x4b/0x70
[ 35.136367] free_netdev+0x1fd/0x450
[ 35.137006] igbvf_probe+0x121d/0x1a10 [igbvf]
[ 35.137808] ? igbvf_vlan_rx_add_vid+0x100/0x100 [igbvf]
[ 35.138751] local_pci_probe+0x13c/0x1f0
[ 35.139461] pci_device_probe+0x37e/0x6c0
[ 35.165526]
[ 35.165806] Allocated by task 366:
[ 35.166414] ____kasan_kmalloc+0xc4/0xf0
[ 35.167117] foo_kmem_cache_alloc_trace+0x3c/0x50 [igbvf]
[ 35.168078] igbvf_probe+0x9c5/0x1a10 [igbvf]
[ 35.168866] local_pci_probe+0x13c/0x1f0
[ 35.169565] pci_device_probe+0x37e/0x6c0
[ 35.179713]
[ 35.179993] Freed by task 366:
[ 35.180539] kasan_set_track+0x4c/0x80
[ 35.181211] kasan_set_free_info+0x1f/0x40
[ 35.181942] ____kasan_slab_free+0x103/0x140
[ 35.182703] kfree+0xe3/0x250
[ 35.183239] igbvf_probe+0x1173/0x1a10 [igbvf]
[ 35.184040] local_pci_probe+0x13c/0x1f0
Fixes: d4e0fe01a3 (igbvf: add new driver to support 82576 virtual functions)
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Letu Ren <fantasquex@gmail.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 584af82154 ]
Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.
Fixes: 1b8b062a99 ("igb: add VF trust infrastructure")
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a708376361 ]
A new warning in clang points out two instances where boolean
expressions are being used with a bitwise OR instead of logical OR:
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: note: cast one or both operands to int to silence this warning
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: note: cast one or both operands to int to silence this warning
2 warnings generated.
The motivation for the warning is that logical operations short circuit
while bitwise operations do not.
In this instance, tegra_fuse_read_spare() is not semantically returning
a boolean, it is returning a bit value. Use u32 for its return type so
that it can be used with either bitwise or boolean operators without any
warnings.
Fixes: 25cd5a3914 ("ARM: tegra: Add speedo-based process identification")
Link: https://github.com/ClangBuiltLinux/linux/issues/1488
Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6692b3b97 ]
The mptcp ULP extension relies on sk->sk_sock_kern being set correctly:
It prevents setsockopt(fd, IPPROTO_TCP, TCP_ULP, "mptcp", 6); from
working for plain tcp sockets (any userspace-exposed socket).
But in case of fallback, accept() can return a plain tcp sk.
In such case, sk is still tagged as 'kernel' and setsockopt will work.
This will crash the kernel, The subflow extension has a NULL ctx->conn
mptcp socket:
BUG: KASAN: null-ptr-deref in subflow_data_ready+0x181/0x2b0
Call Trace:
tcp_data_ready+0xf8/0x370
[..]
Fixes: cf7da0d66c ("mptcp: Create SUBFLOW socket for incoming connections")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 404cd9a221 ]
TCP_ULP setsockopt cannot be used for mptcp because its already
used internally to plumb subflow (tcp) sockets to the mptcp layer.
syzbot managed to trigger a crash for mptcp connections that are
in fallback mode:
KASAN: null-ptr-deref in range [0x0000000000000020-0x0000000000000027]
CPU: 1 PID: 1083 Comm: syz-executor.3 Not tainted 5.16.0-rc2-syzkaller #0
RIP: 0010:tls_build_proto net/tls/tls_main.c:776 [inline]
[..]
__tcp_set_ulp net/ipv4/tcp_ulp.c:139 [inline]
tcp_set_ulp+0x428/0x4c0 net/ipv4/tcp_ulp.c:160
do_tcp_setsockopt+0x455/0x37c0 net/ipv4/tcp.c:3391
mptcp_setsockopt+0x1b47/0x2400 net/mptcp/sockopt.c:638
Remove support for TCP_ULP setsockopt.
Fixes: d9e4c12918 ("mptcp: only admit explicitly supported sockopt")
Reported-by: syzbot+1fd9b69cde42967d1add@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa464957f7 ]
Memory is allocated for gpu_metrics_table in renoir_init_smc_tables(),
but not freed in int smu_v12_0_fini_smc_tables(). Free it!
Fixes: 95868b8576 ("drm/amd/powerplay: add Renoir support for gpu metrics export")
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e4d2f30df ]
[Why]
SMU now respects the PHY refclk disable request from driver.
This causes a hang during hotplug when PHY refclk was disabled
because it's not being re-enabled and the transmitter control
starts on dc_link_detect.
[How]
We normally would re-enable the clk with exit_optimized_pwr_state
but this is only set on DCN21 and DCN301. Set it for dcn31 as well.
This fixes DMCUB timeouts in the PHY.
Fixes: 64b1d0e8d5 ("drm/amd/display: Add DCN3.1 HWSEQ")
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37e738b6fd ]
The driver has to check if it does not accidentally put the timestamp in
the SKB before previous timestamp gets overwritten.
Timestamp values in the PHY are read only and do not get cleared except
at hardware reset or when a new timestamp value is captured.
The cached_tstamp field is used to detect the case where a new timestamp
has not yet been captured, ensuring that we avoid sending stale
timestamp data to the stack.
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0013881c11 ]
Change the division in ice_ptp_adjfine from div_u64 to div64_u64.
div_u64 is used when the divisor is 32 bit but in this case incval is
64 bit and it caused incorrect calculations and incval adjustments.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 166b6a46b7 ]
We need to return EOPNOTSUPP for the unsupported mpls action type when
setup the flow action.
In the original implement, we will return 0 for the unsupported mpls
action type, actually we do not setup it and the following actions
to the flow action entry.
Fixes: 9838b20a7f ("net: sched: take rtnl lock in tc_setup_flow_action()")
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aeb7c75cb7 ]
To replicate the issue:-
1) Add 1 flower filter for VLAN Priority based frame steering:-
$ IFDEVNAME=eth0
$ tc qdisc add dev $IFDEVNAME ingress
$ tc qdisc add dev $IFDEVNAME root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 0 0 0 0 0 0 0 0 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
$ tc filter add dev $IFDEVNAME parent ffff: protocol 802.1Q \
flower vlan_prio 0 hw_tc 0
2) Get the 'pref' id
$ tc filter show dev $IFDEVNAME ingress
3) Delete a specific tc flower record (say pref 49151)
$ tc filter del dev $IFDEVNAME parent ffff: pref 49151
From dmesg, we will observe kernel NULL pointer ooops
[ 197.170464] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 197.171367] #PF: supervisor read access in kernel mode
[ 197.171367] #PF: error_code(0x0000) - not-present page
[ 197.171367] PGD 0 P4D 0
[ 197.171367] Oops: 0000 [#1] PREEMPT SMP NOPTI
<snip>
[ 197.171367] RIP: 0010:tc_setup_cls+0x20b/0x4a0 [stmmac]
<snip>
[ 197.171367] Call Trace:
[ 197.171367] <TASK>
[ 197.171367] ? __stmmac_disable_all_queues+0xa8/0xe0 [stmmac]
[ 197.171367] stmmac_setup_tc_block_cb+0x70/0x110 [stmmac]
[ 197.171367] tc_setup_cb_destroy+0xb3/0x180
[ 197.171367] fl_hw_destroy_filter+0x94/0xc0 [cls_flower]
The above issue is due to previous incorrect implementation of
tc_del_vlan_flow(), shown below, that uses flow_cls_offload_flow_rule()
to get struct flow_rule *rule which is no longer valid for tc filter
delete operation.
struct flow_rule *rule = flow_cls_offload_flow_rule(cls);
struct flow_dissector *dissector = rule->match.dissector;
So, to ensure tc_del_vlan_flow() deletes the right VLAN cls record for
earlier configured RX queue (configured by hw_tc) in tc_add_vlan_flow(),
this patch introduces stmmac_rfs_entry as driver-side flow_cls_offload
record for 'RX frame steering' tc flower, currently used for VLAN
priority. The implementation has taken consideration for future extension
to include other type RX frame steering such as EtherType based.
v2:
- Clean up overly extensive backtrace and rewrite git message to better
explain the kernel NULL pointer issue.
Fixes: 0e039f5cf8 ("net: stmmac: add RX frame steering based on VLAN priority in tc flower")
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
