commit b71f4ade1b upstream.
When ddc_service_construct() is called, it explicitly checks both the
link type and whether there is something on the link which will
dictate whether the pin is marked as hw_supported.
If the pin isn't set or the link is not set (such as from
unloading/reloading amdgpu in an IGT test) then fail the
amdgpu_dm_i2c_xfer() call.
Cc: stable@vger.kernel.org
Fixes: 22676bc500 ("drm/amd/display: Fix dmub soft hang for PSR 1")
Link: https://github.com/fwupd/fwupd/issues/6327
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3938eb956e upstream.
AMD dGPUs have integrated FW that runs as soon as the
device gets power and initializes the board (determines
the amount of memory, provides configuration details to
the driver, etc.). For direct PCIe attached cards this
happens as soon as power is applied and normally completes
well before the OS has even started loading. However, with
hotpluggable ports like USB4, the driver needs to wait for
this to complete before initializing the device.
This normally takes 60-100ms, but could take longer on
some older boards periodically due to memory training.
Retry for up to a second. In the non-hotplug case, there
should be no change in behavior and this should complete
on the first try.
v2: adjust test criteria
v3: adjust checks for the masks, only enable on removable devices
v4: skip bif_fb_en check
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2925
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cb89cd42f upstream.
On GLK CDCLK frequency needs to be at least 2*96 MHz when accessing
the audio hardware. Currently we bump the CDCLK frequency up
temporarily (if not high enough already) whenever audio hardware
is being accessed, and drop it back down afterwards.
With a single active pipe this works just fine as we can switch
between all the valid CDCLK frequencies by changing the cd2x
divider, which doesn't require a full modeset. However with
multiple active pipes the cd2x divider trick no longer works,
and thus we end up blinking all displays off and back on.
To avoid this let's just bump the CDCLK frequency to >=2*96MHz
whenever multiple pipes are active. The downside is slightly
higher power consumption, but that seems like an acceptable
tradeoff. With a single active pipe we can stick to the current
more optiomal (from power comsumption POV) behaviour.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9599
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231031160800.18371-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 451eaa1a61)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08e9ebc75b upstream.
The incoming strings might not be terminated by a newline
or a 0.
(found while testing a program that just wrote the string
itself, causing a crash)
Cc: stable@vger.kernel.org
Fixes: e3933f26b6 ("drm/amd/pp: Add edit/commit/show OD clock/voltage support in sysfs")
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce56d21355 upstream.
syzbot reports that the following warning from ext4_iomap_begin()
triggers as of the commit referenced below:
if (WARN_ON_ONCE(ext4_has_inline_data(inode)))
return -ERANGE;
This occurs during a dio write, which is never expected to encounter
an inode with inline data. To enforce this behavior,
ext4_dio_write_iter() checks the current inline state of the inode
and clears the MAY_INLINE_DATA state flag to either fall back to
buffered writes, or enforce that any other writers in progress on
the inode are not allowed to create inline data.
The problem is that the check for existing inline data and the state
flag can span a lock cycle. For example, if the ilock is originally
locked shared and subsequently upgraded to exclusive, another writer
may have reacquired the lock and created inline data before the dio
write task acquires the lock and proceeds.
The commit referenced below loosens the lock requirements to allow
some forms of unaligned dio writes to occur under shared lock, but
AFAICT the inline data check was technically already racy for any
dio write that would have involved a lock cycle. Regardless, lift
clearing of the state bit to the same lock critical section that
checks for preexisting inline data on the inode to close the race.
Cc: stable@kernel.org
Reported-by: syzbot+307da6ca5cb0d01d581a@syzkaller.appspotmail.com
Fixes: 310ee0902b ("ext4: allow concurrent unaligned dio overwrites")
Signed-off-by: Brian Foster <bfoster@redhat.com>
Link: https://lore.kernel.org/r/20231002185020.531537-1-bfoster@redhat.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40dd7953f4 upstream.
Wrong check of gdb backup in meta bg as following:
first_group is the first group of meta_bg which contains target group, so
target group is always >= first_group. We check if target group has gdb
backup by comparing first_group with [group + 1] and [group +
EXT4_DESC_PER_BLOCK(sb) - 1]. As group >= first_group, then [group + N] is
> first_group. So no copy of gdb backup in meta bg is done in
setup_new_flex_group_blocks.
No need to do gdb backup copy in meta bg from setup_new_flex_group_blocks
as we always copy updated gdb block to backups at end of
ext4_flex_group_add as following:
ext4_flex_group_add
/* no gdb backup copy for meta bg any more */
setup_new_flex_group_blocks
/* update current group number */
ext4_update_super
sbi->s_groups_count += flex_gd->count;
/*
* if group in meta bg contains backup is added, the primary gdb block
* of the meta bg will be copy to backup in new added group here.
*/
for (; gdb_num <= gdb_num_end; gdb_num++)
update_backups(...)
In summary, we can remove wrong gdb backup copy code in
setup_new_flex_group_blocks.
Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20230826174712.4059355-5-shikemeng@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40ea98396a upstream.
When big allocate feature is enabled, we need to count and update
reserved clusters before removing a delayed only extent_status entry.
{init|count|get}_rsvd() have already done this, but the start block
number of this counting isn't correct in the following case.
lblk end
| |
v v
-------------------------
| | orig_es
-------------------------
^ ^
len1 is 0 | len2 |
If the start block of the orig_es entry founded is bigger than lblk, we
passed lblk as start block to count_rsvd(), but the length is correct,
finally, the range to be counted is offset. This patch fix this by
passing the start blocks to 'orig_es->lblk + len1'.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20230824092619.1327976-2-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cd8bdb5ef upstream.
** Short Version **
In ext4 with dioread_nolock, we could have a scenario where the bh returned by
get_blocks (ext4_get_block_unwritten()) in __block_write_begin_int() has
UNWRITTEN and MAPPED flag set. Since such a bh does not have NEW flag set we
never zero out the range of bh that is not under write, causing whatever stale
data is present in the folio at that time to be written out to disk. To fix this
mark the buffer as new, in case it is unwritten, in ext4_get_block_unwritten().
** Long Version **
The issue mentioned above was resulting in two different bugs:
1. On block size < page size case in ext4, generic/269 was reliably
failing with dioread_nolock. The state of the write was as follows:
* The write was extending i_size.
* The last block of the file was fallocated and had an unwritten extent
* We were near ENOSPC and hence we were switching to non-delayed alloc
allocation.
In this case, the back trace that triggers the bug is as follows:
ext4_da_write_begin()
/* switch to nodelalloc due to low space */
ext4_write_begin()
ext4_should_dioread_nolock() // true since mount flags still have delalloc
__block_write_begin(..., ext4_get_block_unwritten)
__block_write_begin_int()
for(each buffer head in page) {
/* first iteration, this is bh1 which contains i_size */
if (!buffer_mapped)
get_block() /* returns bh with only UNWRITTEN and MAPPED */
/* second iteration, bh2 */
if (!buffer_mapped)
get_block() /* we fail here, could be ENOSPC */
}
if (err)
/*
* this would zero out all new buffers and mark them uptodate.
* Since bh1 was never marked new, we skip it here which causes
* the bug later.
*/
folio_zero_new_buffers();
/* ext4_wrte_begin() error handling */
ext4_truncate_failed_write()
ext4_truncate()
ext4_block_truncate_page()
__ext4_block_zero_page_range()
if(!buffer_uptodate())
ext4_read_bh_lock()
ext4_read_bh() -> ... ext4_submit_bh_wbc()
BUG_ON(buffer_unwritten(bh)); /* !!! */
2. The second issue is stale data exposure with page size >= blocksize
with dioread_nolock. The conditions needed for it to happen are same as
the previous issue ie dioread_nolock around ENOSPC condition. The issue
is also similar where in __block_write_begin_int() when we call
ext4_get_block_unwritten() on the buffer_head and the underlying extent
is unwritten, we get an unwritten and mapped buffer head. Since it is
not new, we never zero out the partial range which is not under write,
thus writing stale data to disk. This can be easily observed with the
following reproducer:
fallocate -l 4k testfile
xfs_io -c "pwrite 2k 2k" testfile
# hexdump output will have stale data in from byte 0 to 2k in testfile
hexdump -C testfile
NOTE: To trigger this, we need dioread_nolock enabled and write happening via
ext4_write_begin(), which is usually used when we have -o nodealloc. Since
dioread_nolock is disabled with nodelalloc, the only alternate way to call
ext4_write_begin() is to ensure that delayed alloc switches to nodelalloc ie
ext4_da_write_begin() calls ext4_write_begin(). This will usually happen when
ext4 is almost full like the way generic/269 was triggering it in Issue 1 above.
This might make the issue harder to hit. Hence, for reliable replication, I used
the below patch to temporarily allow dioread_nolock with nodelalloc and then
mount the disk with -o nodealloc,dioread_nolock. With this you can hit the stale
data issue 100% of times:
@@ -508,8 +508,8 @@ static inline int ext4_should_dioread_nolock(struct inode *inode)
if (ext4_should_journal_data(inode))
return 0;
/* temporary fix to prevent generic/422 test failures */
- if (!test_opt(inode->i_sb, DELALLOC))
- return 0;
+ // if (!test_opt(inode->i_sb, DELALLOC))
+ // return 0;
return 1;
}
After applying this patch to mark buffer as NEW, both the above issues are
fixed.
Signed-off-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Cc: stable@kernel.org
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: "Ritesh Harjani (IBM)" <ritesh.list@gmail.com>
Link: https://lore.kernel.org/r/d0ed09d70a9733fbb5349c5c7b125caac186ecdf.1695033645.git.ojaswin@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31f13421c0 upstream.
Commit 0aeaa2559d ("ext4: fix corruption when online resizing a 1K
bigalloc fs") found that primary superblock's offset in its group is
not equal to offset of backup superblock in its group when block size
is 1K and bigalloc is enabled. As group descriptor blocks are right
after superblock, we can't pass block number of gdb to update_backups
for the same reason.
The root casue of the issue above is that leading 1K padding block is
count as data block offset for primary block while backup block has no
padding block offset in its group.
Remove padding data block count to fix the issue for gdb backups.
For meta_bg case, update_backups treat blk_off as block number, do no
conversion in this case.
Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20230826174712.4059355-2-shikemeng@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e387c89e9 upstream.
__insert_pending() allocate memory in atomic context, so the allocation
could fail, but we are not handling that failure now. It could lead
ext4_es_remove_extent() to get wrong reserved clusters, and the global
data blocks reservation count will be incorrect. The same to
extents_status entry preallocation, preallocate pending entry out of the
i_es_lock with __GFP_NOFAIL, make sure __insert_pending() and
__revise_pending() always succeeds.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20230824092619.1327976-3-yi.zhang@huaweicloud.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebf6cb7c6e upstream.
Commit 7a2fcbf7f8 ("ext4: don't use blocks freed but not yet committed in
buddy cache init") added a code to mark as used blocks in the list of not yet
committed freed blocks during initialization of a buddy page. However
ext4_mb_free_metadata() makes sure buddy page is already loaded and takes a
reference to it so it cannot happen that ext4_mb_init_cache() is called
when efd list is non-empty. Just remove the
ext4_mb_generate_from_freelist() call.
Fixes: 7a2fcbf7f85('ext4: don't use blocks freed but not yet committed in buddy cache init')
Signed-off-by: Wang Jianjian <wangjianjian0@foxmail.com>
Link: https://lore.kernel.org/r/tencent_53CBCB1668358AE862684E453DF37B722008@qq.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 745f17a416 upstream.
We got a WARNING in ext4_add_complete_io:
==================================================================
WARNING: at fs/ext4/page-io.c:231 ext4_put_io_end_defer+0x182/0x250
CPU: 10 PID: 77 Comm: ksoftirqd/10 Tainted: 6.3.0-rc2 #85
RIP: 0010:ext4_put_io_end_defer+0x182/0x250 [ext4]
[...]
Call Trace:
<TASK>
ext4_end_bio+0xa8/0x240 [ext4]
bio_endio+0x195/0x310
blk_update_request+0x184/0x770
scsi_end_request+0x2f/0x240
scsi_io_completion+0x75/0x450
scsi_finish_command+0xef/0x160
scsi_complete+0xa3/0x180
blk_complete_reqs+0x60/0x80
blk_done_softirq+0x25/0x40
__do_softirq+0x119/0x4c8
run_ksoftirqd+0x42/0x70
smpboot_thread_fn+0x136/0x3c0
kthread+0x140/0x1a0
ret_from_fork+0x2c/0x50
==================================================================
Above issue may happen as follows:
cpu1 cpu2
----------------------------|----------------------------
mount -o dioread_lock
ext4_writepages
ext4_do_writepages
*if (ext4_should_dioread_nolock(inode))*
// rsv_blocks is not assigned here
mount -o remount,dioread_nolock
ext4_journal_start_with_reserve
__ext4_journal_start
__ext4_journal_start_sb
jbd2__journal_start
*if (rsv_blocks)*
// h_rsv_handle is not initialized here
mpage_map_and_submit_extent
mpage_map_one_extent
dioread_nolock = ext4_should_dioread_nolock(inode)
if (dioread_nolock && (map->m_flags & EXT4_MAP_UNWRITTEN))
mpd->io_submit.io_end->handle = handle->h_rsv_handle
ext4_set_io_unwritten_flag
io_end->flag |= EXT4_IO_END_UNWRITTEN
// now io_end->handle is NULL but has EXT4_IO_END_UNWRITTEN flag
scsi_finish_command
scsi_io_completion
scsi_io_completion_action
scsi_end_request
blk_update_request
req_bio_endio
bio_endio
bio->bi_end_io > ext4_end_bio
ext4_put_io_end_defer
ext4_add_complete_io
// trigger WARN_ON(!io_end->handle && sbi->s_journal);
The immediate cause of this problem is that ext4_should_dioread_nolock()
function returns inconsistent values in the ext4_do_writepages() and
mpage_map_one_extent(). There are four conditions in this function that
can be changed at mount time to cause this problem. These four conditions
can be divided into two categories:
(1) journal_data and EXT4_EXTENTS_FL, which can be changed by ioctl
(2) DELALLOC and DIOREAD_NOLOCK, which can be changed by remount
The two in the first category have been fixed by commit c8585c6fca
("ext4: fix races between changing inode journal mode and ext4_writepages")
and commit cb85f4d23f ("ext4: fix race between writepages and enabling
EXT4_EXTENTS_FL") respectively.
Two cases in the other category have not yet been fixed, and the above
issue is caused by this situation. We refer to the fix for the first
category, when applying options during remount, we grab s_writepages_rwsem
to avoid racing with writepages ops to trigger this problem.
Fixes: 6b523df4fb ("ext4: use transaction reservation for extent conversion in ext4_end_io")
Cc: stable@vger.kernel.org
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230524072538.2883391-1-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a26310273 upstream.
This reverts commit efa5f1311c.
I couldn't reproduce the reported issue. What I did, based on a pcap
packet log provided by the reporter:
- Used same chip version (RTL8168h)
- Set MAC address to the one used on the reporters system
- Replayed the EAPOL unicast packet that, according to the reporter,
was filtered out by the mc filter.
The packet was properly received.
Therefore the root cause of the reported issue seems to be somewhere
else. Disabling mc filtering completely for the most common chip
version is a quite big hammer. Therefore revert the change and wait
for further analysis results from the reporter.
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87889f1b7e upstream.
In the current driver csid Test Pattern Generator (TPG) doesn't work.
This change:
- fixes writing frame width and height values into CSID_TPG_DT_n_CFG_0
- fixes the shift by one between test_pattern control value and the
actual pattern.
- drops fixed VC of 0x0a which testing showed prohibited some test
patterns in the CSID to produce output.
So that TPG starts working, but with the below limitations:
- only test_pattern=9 works as it should
- test_pattern=8 and test_pattern=7 produce black frame (all zeroes)
- the rest of test_pattern's don't work (yavta doesn't get the data)
- regardless of the CFA pattern set by 'media-ctl -V' the actual pixel
order is always the same (RGGB for any RAW8 or RAW10P format in
4608x2592 resolution).
Tested with:
RAW10P format, VC0:
media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video0
RAW10P format, VC1:
media-ctl -V '"msm_csid0":2[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi1":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -l '"msm_csid0":2->"msm_vfe0_rdi1":0[1]'
v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video1
RAW8 format, VC0:
media-ctl --reset
media-ctl -V '"msm_csid0":0[fmt:SRGGB8/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB8/4608x2592 field:none]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB8 -s 4608x2592 /dev/video0
Fixes: eebe6d00e9 ("media: camss: Add support for CSID hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f24d29135 upstream.
vfe-480 is copied from vfe-17x and has the same racy idle timeout bug as in
17x.
Fix the vfe_disable_output() logic to no longer be racy and to conform
to the 17x way of quiescing and then resetting the VFE.
Fixes: 4edc8eae71 ("media: camss: Add initial support for VFE hardware version Titan 480")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3143ad282f upstream.
There are two problems with the current vfe_disable_output() routine.
Firstly we rightly use a spinlock to protect output->gen2.active_num
everywhere except for in the IDLE timeout path of vfe_disable_output().
Even if that is not racy "in practice" somehow it is by happenstance not
by design.
Secondly we do not get consistent behaviour from this routine. On
sc8280xp 50% of the time I get "VFE idle timeout - resetting". In this
case the subsequent capture will succeed. The other 50% of the time, we
don't hit the idle timeout, never do the VFE reset and subsequent
captures stall indefinitely.
Rewrite the vfe_disable_output() routine to
- Quiesce write masters with vfe_wm_stop()
- Set active_num = 0
remembering to hold the spinlock when we do so followed by
- Reset the VFE
Testing on sc8280xp and sdm845 shows this to be a valid fix.
Fixes: 7319cdf189 ("media: camss: Add support for VFE hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7405116519 upstream.
We need to make sure camss_configure_pd() happens before
camss_register_entities() as the vfe_get() path relies on the pointer
provided by camss_configure_pd().
Fix the ordering sequence in probe to ensure the pointers vfe_get() demands
are present by the time camss_register_entities() runs.
In order to facilitate backporting to stable kernels I've moved the
configure_pd() call pretty early on the probe() function so that
irrespective of the existence of the old error handling jump labels this
patch should still apply to -next circa Aug 2023 to v5.13 inclusive.
Fixes: 2f6f8af672 ("media: camss: Refactor VFE power domain toggling")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ab0c45d8a upstream.
For devices that support DASH, even DASH is disabled, there may still
exist a default firmware that will influence device behavior.
So driver needs to handle DASH for devices that support DASH, no
matter the DASH status is.
This patch also prepares for "fix network lost after resume on DASH
systems".
Fixes: ee7a1beb97 ("r8169:call "rtl8168_driver_start" "rtl8168_driver_stop" only when hardware dash function is enabled")
Cc: stable@vger.kernel.org
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20231109173400.4573-2-hau@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman
Lewis Huang
Paul Hsieh
Tianci Yin
Mario Limonciello
Fangzhi Zuo
Nicholas Kazlauskas
Felix Kuehling
Christian König
Alex Deucher
Tim Huang
Ma Jun
Nirmoy Das
Kunwu Chan
Ville Syrjälä
Chaitanya Kumar Borah
Gabe Teeger
Josh Poimboeuf
Jani Nikula
Bas Nieuwenhuizen
Brian Foster
Jan Kara
Kemeng Shi
Zhang Yi
Ojaswin Mujoo
Max Kellermann
Wang Jianjian
Baokun Li
Heiner Kallweit
Jiri Kosina
Andrey Konovalov
Bryan O'Donoghue
Victor Shih
ChunHao Lin