commit c78a4e41ab upstream.
Each PPP control protocol (LCP/IPCP/IPV6CP) embedded in struct ppp
registers a timer via timer_setup(). That struct ppp is the
hdlc->state allocation, which detach_hdlc_protocol() frees with kfree()
in both teardown paths: unregister_hdlc_device() and the re-attach inside
attach_hdlc_protocol().
The ppp proto never registered a .detach callback, so
detach_hdlc_protocol() performs no timer synchronization before the
kfree(). The only cancel, timer_delete(&proto->timer) in ppp_cp_event(),
is partial (it does not wait for a running callback) and only runs on the
->CLOSED transition; ppp_stop()/ppp_close() do not sync either. A
ppp_timer callback already executing (blocked on ppp->lock) survives the
kfree and then dereferences proto->state / ppp->lock in freed memory,
leading to a use-after-free.
Fix this by adding a .detach helper that calls timer_shutdown_sync() on
every per-proto timer. detach_hdlc_protocol() invokes proto->detach(dev)
before kfree(hdlc->state), so timer_shutdown_sync()
now runs on both free paths.
timer_shutdown_sync() is used instead of timer_delete_sync() because the
keepalive path re-arms the timer through add_timer()/mod_timer() and
shutdown blocks any re-activation during teardown.
Initialize the per-protocol timers in ppp_ioctl() when the protocol is
attached, and remove the now-redundant timer_setup() from ppp_start(), so
that the timers are initialized exactly once at attach time and
ppp_timer_release() never operates on uninitialized timer_list
structures. attach_hdlc_protocol() uses kmalloc() (not kzalloc), so
struct ppp's protos[i].timer is uninitialized garbage until the first
timer_setup(); without this init-at-attach, attaching the PPP protocol
without ever bringing the device up would leave timer_shutdown_sync()
operating on uninitialized memory in .detach. Moving the init out of
ppp_start() (which only runs on NETDEV_UP) into the attach path makes the
initialization unconditional and avoids initializing the same timer_list
twice.
This bug was found by static analysis.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Link: https://patch.msgid.link/20260617020518.116319-1-fanwu01@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 257595adf9 upstream.
pwrseq_debugfs_seq_next() declares 'next' with __free(put_device),
which causes put_device() to be called on the returned pointer when
the variable goes out of scope. This results in a use-after-free
since the seq_file framework receives a pointer whose reference has
already been dropped.
Simply removing __free(put_device) would fix the UAF but would leak
the reference acquired by bus_find_next_device(), as stop() only
calls up_read(&pwrseq_sem) and never releases the device reference.
Fix this by making the reference counting consistent across all
seq_file callbacks, matching the standard pattern used by PCI and
SCSI:
- start(): use get_device() so it returns a referenced pointer.
- next(): explicitly put_device(curr) to release the previous
device's reference (no NULL check needed - the seq_file framework
only calls next() while the previous return was non-NULL).
- stop(): put_device(data) to release the last iterated device's
reference, with a NULL guard since stop() may be called with NULL
when start() returned NULL or next() reached end-of-sequence.
Cc: stable@vger.kernel.org
Fixes: 249ebf3f65 ("power: sequencing: implement the pwrseq core")
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20260616151049.1705503-1-vulab@iscas.ac.cn
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9c9ec2c31 upstream.
gfs2_qd_dealloc(), called as an RCU callback from gfs2_qd_dispose(),
accesses the superblock object sdp through qd->qd_sbd after freeing qd.
It does so to decrement sd_quota_count and wake up sd_kill_wait.
However, by the time the RCU callback runs, gfs2_put_super() may have
already freed sdp via free_sbd(). This can happen when
gfs2_quota_cleanup() is called during unmount: it disposes of quota
objects via call_rcu() and then waits on sd_kill_wait with a 60-second
timeout. If the timeout expires, or if gfs2_gl_hash_clear() triggers
additional qd_put() calls that schedule more RCU callbacks after the
wait completes, gfs2_put_super() will proceed to free the superblock
while RCU callbacks referencing it are still pending.
Add an rcu_barrier() before free_sbd() in gfs2_put_super() to ensure
all pending RCU callbacks (including gfs2_qd_dealloc) have completed
before the superblock is freed.
Fixes: a475c5dd16 ("gfs2: Free quota data objects synchronously")
Reported-by: syzbot+42a37bf8045847d8f9d2@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=42a37bf8045847d8f9d2
Tested-by: syzbot+42a37bf8045847d8f9d2@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Tristan Madani <tristan@talencesecurity.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e67f504ee upstream.
nx_crypto_ctx_shash_exit calls nx_crypto_ctx_exit with crypto_shash_ctx(...)
but crypto_shash_ctx gives a nx_crypto_ctx *, not a crypto_tfm *.
Fix the type in nx_crypto_ctx_exit and drop the bogus crypto_tfm_ctx
call.
This fixes the following oops:
BUG: Unable to handle kernel data access at 0xc0403effffffffc8
Faulting instruction address: 0xc000000000396cb4
Oops: Kernel access of bad area, sig: 11 [#15]
Call Trace:
nx_crypto_ctx_shash_exit+0x24/0x60
crypto_shash_exit_tfm+0x28/0x40
crypto_destroy_tfm+0x98/0x140
crypto_exit_ahash_using_shash+0x20/0x40
crypto_destroy_tfm+0x98/0x140
hash_release+0x1c/0x30
alg_sock_destruct+0x38/0x60
__sk_destruct+0x48/0x2b0
af_alg_release+0x58/0xb0
__sock_release+0x68/0x150
sock_close+0x20/0x40
__fput+0x110/0x3a0
sys_close+0x48/0xa0
system_call_exception+0x140/0x2d0
system_call_common+0xf4/0x258
.. which came from hardlink(1) opportunistically using AF_ALG.
The same problem exists with nx_crypto_ctx_skcipher_exit getting a context
it wasn't expecting, but apparently nobody hit that for years.
Cc: Eric Biggers <ebiggers@kernel.org>
Cc: stable@vger.kernel.org
Fixes: bfd9efddf9 ("crypto: nx - convert AES-ECB to skcipher API")
Fixes: 9420e628e7 ("crypto: nx - Use API partial block handling")
Acked-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Reported-by: Calvin Buckley <calvin@cmpct.info>
Tested-by: Calvin Buckley <calvin@cmpct.info>
Suggested-by: Brad Spengler <brad.spengler@opensrcsec.com>
Signed-off-by: Sam James <sam@gentoo.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1edbed787 upstream.
Drop a BUG_ON() that has been reachable since it was first added, way back
in 2009, and instead use get_unaligned() to perform potentially-unaligned
accesses.
For a given store, KVM x86's emulator tracks the entire value in the
destination operand, x86_emulate_ctxt.dst. If the destination is memory,
and the target splits multiple pages and/or is emulated MMIO, then KVM
handles each fragment independently. E.g. on a page split starting at page
offset 0xffc, KVM writes 4 bytes to the first page, then the remaining
bytes to the second page, using ctxt->dst as the source for both (with
appropriate offsets).
If the destination splits a page *and* hits emulated MMIO on the second
page, then KVM will complete the write to the first page, then emulate the
MMIO access to the second page. If there is a datamatch-enabled ioeventfd
at offset 0 of the second page, then KVM will process the remainder of the
store as a potential ioeventfd signal.
Putting it all together, if the guest emits a store that splits a page
starting at page offset N, and the second page has a datamatch-enabled
ioeventfd at offset 0, then KVM will check for datamatch using
&dst.valptr[N] as the source. Due to dst (and thus dst.valptr) being
32-byte aligned, if N is not aligned to @len, the BUG_ON() fires.
E.g. with a 16-byte store at page offset 0xffc, to an ioeventfd of len 8,
all initial checks in ioeventfd_in_range() will succeed, and the BUG_ON()
fires due to @val being 4-byte aligned, but not 8-byte aligned.
------------[ cut here ]------------
kernel BUG at arch/x86/kvm/../../../virt/kvm/eventfd.c:783!
Oops: invalid opcode: 0000 [#1] SMP
CPU: 0 UID: 1000 PID: 615 Comm: repro Not tainted 7.1.0-rc2-ff238429d1ea #365 PREEMPT
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:ioeventfd_write+0x6c/0x70 [kvm]
Call Trace:
<TASK>
__kvm_io_bus_write+0x85/0xb0 [kvm]
kvm_io_bus_write+0x53/0x80 [kvm]
vcpu_mmio_write+0x66/0xf0 [kvm]
emulator_read_write_onepage+0x12a/0x540 [kvm]
emulator_read_write+0x109/0x2b0 [kvm]
x86_emulate_insn+0x4f8/0xfb0 [kvm]
x86_emulate_instruction+0x181/0x790 [kvm]
kvm_mmu_page_fault+0x313/0x630 [kvm]
vmx_handle_exit+0x18a/0x590 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0xc81/0x1c90 [kvm]
kvm_vcpu_ioctl+0x2d5/0x970 [kvm]
__x64_sys_ioctl+0x8a/0xd0
do_syscall_64+0xb7/0x890
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f19c931a9bf
</TASK>
Modules linked in: kvm_intel kvm irqbypass
---[ end trace 0000000000000000 ]---
In a perfect world, the fix would be to simply delete the BUG_ON(), as KVM
x86 doesn't perform alignment checks on "normal" memory accesses at CPL0.
Sadly, C99 ruins all the fun; while the x86 architecture plays nice,
dereferencing an unaligned pointer directly is undefined behavior in C,
e.g. triggers splats when running with CONFIG_UBSAN_ALIGNMENT=y.
Fixes: d34e6b175e ("KVM: add ioeventfd support")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20260612225241.678509-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef057cbf82 upstream.
When recovering hugepages in the shadow MMU, verify that the base gfn of
the shadow page is actually contained within the target memslot, *before*
querying the max mapping level given the shadow page's gfn. Failure to
pre-check the validity of the gfn can lead to an out-of-bounds access to
the slot's lpage_info (which typically manifests as a host #PF because the
lpage_info is vmalloc'd) if the guest creates a hugepage mapping (in its
PTEs) that extends "below" the bounds of a memslot.
When faulting in memory for a guest, and the size of the guest mapping is
greater than KVM's (current) max mapping, then KVM will create a "direct"
shadow page (direct in that there are no gPTEs to shadow, and so the target
gfn is a direct calculation given the base gfn of the shadow page). The
hugepage recovery flow looks for such direct shadow pages, as forcing 4KiB
mappings when dirty logging generates the guest > host mapping size case.
When the 4KiB restriction is lifted, then KVM can replace the shadow page
with a hugepage.
But if KVM originally used a smaller mapping than the guest because the
range of memory covered by the guest hugepage exceeds the bounds of a
memslot, then KVM will link a direct shadow page with a gfn that is outside
the bounds of the memslot being used to fault in memory. The rmap entry
added for the leaf mapping is correct and within bounds, but the gfn of the
leaf SPTE's parent shadow page will be out of bounds.
BUG: unable to handle page fault for address: ffffc90000806ffc
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 100000067 P4D 100000067 PUD 1002a7067 PMD 10612f067 PTE 0
Oops: Oops: 0000 [#1] SMP
CPU: 13 UID: 1000 PID: 757 Comm: mmu_stress_test Not tainted 7.1.0-rc1-48ce1e26eace-x86_pir_to_irr_comments-vm #341 PREEMPT
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:kvm_mmu_max_mapping_level+0x79/0x2b0 [kvm]
Call Trace:
<TASK>
kvm_mmu_recover_huge_pages+0x21b/0x320 [kvm]
kvm_set_memslot+0x1ee/0x590 [kvm]
kvm_set_memory_region.part.0+0x3a1/0x4d0 [kvm]
kvm_vm_ioctl+0x9bf/0x15d0 [kvm]
__x64_sys_ioctl+0x8a/0xd0
do_syscall_64+0xb7/0xbb0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f21c0f1a9bf
</TASK>
Don't bother pre-checking the bounds of the potential hugepage, i.e. don't
check that e.g. sp->gfn + KVM_PAGES_PER_HPAGE(sp->role.level + 1) is also
within the memslot, as the checks performed by kvm_mmu_max_mapping_level()
are a superset of the basic bounds checks. I.e. pre-checking the full
range would be a dubious micro-optimization.
Fixes: 9eba50f8d7 ("KVM: x86/mmu: Consult max mapping level when zapping collapsible SPTEs")
Cc: stable@vger.kernel.org
Cc: David Matlack <dmatlack@google.com>
Cc: James Houghton <jthoughton@google.com>
Cc: Alexander Bulekov <bkov@amazon.com>
Cc: Fred Griffoul <fgriffo@amazon.co.uk>
Cc: Alexander Graf <graf@amazon.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Filippo Sironi <sironi@amazon.de>
Cc: Ivan Orlov <iorlov@amazon.co.uk>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f5f8ee991 upstream.
In exfat_find_dir_entry(), the buffer_head obtained from
exfat_get_dentry() is released with brelse(bh) before the fall-through
TYPE_EXTEND branch reads the directory entry through ep (which points
into bh->b_data):
brelse(bh);
if (entry_type == TYPE_EXTEND) {
...
len = exfat_extract_uni_name(ep, entry_uniname);
...
}
After brelse() drops our reference, nothing guarantees that the
underlying page backing bh->b_data remains valid for the subsequent
exfat_extract_uni_name() read. This is the same pattern fixed in
commit fc961522dd ("exfat: Fix potential use after free in
exfat_load_upcase_table()").
Move brelse(bh) so it runs after ep is no longer dereferenced on
each branch.
Confirmed on QEMU x86_64 with CONFIG_KASAN=y + CONFIG_DEBUG_PAGEALLOC=y
+ CONFIG_PAGE_POISONING=y on linux-next, using a crafted exFAT image
(long filename with same-hash collisions forcing the TYPE_EXTEND path).
With a debug-only invalidate_bdev() inserted between brelse(bh) and
the ep read to make the stale-deref window deterministic, the
unpatched kernel faults:
BUG: KASAN: use-after-free in exfat_find_dir_entry+0x133b/0x15a0
BUG: unable to handle page fault for address: ffff88801a5fa0c2
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN NOPTI
RIP: 0010:exfat_find_dir_entry+0x1188/0x15a0
With this patch applied, the same instrumented harness completes
cleanly under the same sanitizer stack. I have not reproduced a
crash on an uninstrumented kernel under ordinary reclaim; the
instrumented A/B establishes the lifetime violation and that the
patch closes it, not an unaided triggerability claim.
Fixes: ca06197382 ("exfat: add directory operations")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fb13fd351 upstream.
In 64-bit configurations calling the initial console output handler from
a kernel thread other than the initial one will result in a situation
where the stack has been placed in the XKPHYS 64-bit memory segment and
consequently so has been the buffer allocated there that is used as the
argument corresponding to the `%s' output conversion specifier for the
firmware's printf() entry point.
This 64-bit address will then be truncated by 32-bit firmware, resulting
in an attempt to access the wrong memory location, which in turn will
cause all kinds of unpredictable behaviour, such as a kernel crash:
Console: colour dummy device 160x64
Calibrating delay loop... 49.36 BogoMIPS (lpj=192512)
pid_max: default: 32768 minimum: 301
CPU 0 Unable to handle kernel paging request at virtual address 000000000203bd00, epc == ffffffffbfc08364, ra == ffffffffbfc08800
Oops[#1]:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.18.0-rc2-00254-gfb649bda6f56-dirty #121
$ 0 : 0000000000000000 0000000000000001 0000000000000023 ffffffff80684ba0
$ 4 : 000000000203bd00 ffffffffbfc0f3b4 ffffffffffffffff 0000000000000073
$ 8 : 0a303d7469000000 0000000000000000 0000000000000073 ffffffffbfc0f473
$12 : 0000000000000002 0000000000000000 ffffffff80684c1c 0000000000000000
$16 : 0000000000000000 ffffffff80596dc9 0000000000000000 ffffffffbfc09240
$20 : ffffffff80684c40 ffffffffbfc0f400 000000000000002d 000000000000002b
$24 : ffffffffffffffbf 000000000203bd00
$28 : ffffffff805f0000 ffffffff80684b58 0000000000000030 ffffffffbfc08800
Hi : 0000000000000000
Lo : 0000000000000aa8
epc : ffffffffbfc08364 0xffffffffbfc08364
ra : ffffffffbfc08800 0xffffffffbfc08800
Status: 140120e2 KX SX UX KERNEL EXL
Cause : 00000008 (ExcCode 02)
BadVA : 000000000203bd00
PrId : 00000430 (R4000SC)
Modules linked in:
Process swapper (pid: 0, threadinfo=(____ptrval____), task=(____ptrval____), tls=0000000000000000)
Stack : 0000000000000000 0000000000000000 0000000000000000 0000004d0000004d
80684cc0806a2a40 80596dc80000004d 8061000000000000 bfc0850c80684c38
0000000000000000 000000000203bd00 0000000000000000 0000000000000000
0000000000000000 00000000bfc0f3b4 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000002500000000 0000000000000000 0000000000000000 802c1a7400000000
0203bd0080596dc8 0203bd4d69000000 6c61632000000018 5f746567646e6172
6c616320625f6d6f 5f736e5f6d6f7266 206361323778302b 303d74696e726320
806a0a38806b0000 806a0a38806b0000 00000000806b0000 80683c58806b0000
...
Call Trace:
Code: a082ffff 03e00008 00601021 <80820000> 00001821 10400005 24840001 80820000 24630001
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: Fatal exception in interrupt
KN04 V2.1k (PC: 0xa0026768, SP: 0x806848e8)
>>
In this case the pointer in $4 was truncated from 0x980000000203bd00 to
0x000000000203bd00.
This may happen when no final console driver has been enabled in the
configuration and consequently the initial console continues being used
late into bootstrap or with an upcoming change that will switch the zs
driver to use a platform device, which in turn will make the console
handover happen only after other kernel threads have already been
started.
Fix the issue by making the buffer static and initdata, and therefore
placed in the CKSEG0 32-bit compatibility segment, observing that the
console output handler is called with the console lock held, implying
no need for this code to be reentrant. Add an assertion to verify the
buffer actually has been placed in a compatibility segment.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # v2.6.12+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c21b5927d upstream.
proc_sys_call_handler() allocates its temporary sysctl buffer with
kvzalloc() and passes it to __cgroup_bpf_run_filter_sysctl(). Since
kvzalloc() may fall back to vmalloc() for large allocations, freeing
that buffer with kfree() is wrong and can corrupt memory.
Use kvfree() to safely handle both kmalloc and kvzalloc()/vmalloc
allocations.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1-rc5.
Reproduced the bug based on v7.1-rc4 in a QEMU x86_64 guest booted with
KASAN and CONFIG_FAILSLAB enabled. To exercise the replacement path, the
test tree also included the accompanying fix for the stale ret == 1
check in __cgroup_bpf_run_filter_sysctl(). The reproducer confines
failslab injections to the proc_sys_call_handler() range, uses
stacktrace-depth=32, and injects fail-nth=1 while writing 8191 bytes to
/proc/sys/kernel/domainname from a task in the target cgroup. Under
that setup, fail-nth=1 triggered the fault:
BUG: unable to handle page fault for address: ffffeb0200024d48
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 SMP KASAN NOPTI
CPU: 2 UID: 0 PID: 209 Comm: repro_proc_sys_ Not tainted 7.1.0-rc4-00686-g97625979a5d4 PREEMPT(lazy)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014
RIP: 0010:kfree+0x6e/0x510
...
Call Trace:
<TASK>
? __cgroup_bpf_run_filter_sysctl+0x626/0xc30
__cgroup_bpf_run_filter_sysctl+0x74d/0xc30
? __pfx___cgroup_bpf_run_filter_sysctl+0x10/0x10
? srso_return_thunk+0x5/0x5f
? __kvmalloc_node_noprof+0x345/0x870
? proc_sys_call_handler+0x250/0x480
? srso_return_thunk+0x5/0x5f
proc_sys_call_handler+0x3a2/0x480
? __pfx_proc_sys_call_handler+0x10/0x10
? srso_return_thunk+0x5/0x5f
? selinux_file_permission+0x39f/0x500
? srso_return_thunk+0x5/0x5f
? lock_is_held_type+0x9e/0x120
vfs_write+0x98e/0x1000
...
</TASK>
With this fix applied on top of the same test setup, rerunning the
reproducer with fail-nth=1 yields no corresponding Oops reports.
Fixes: 4508943794 ("proc: use kvzalloc for our kernel buffer")
Cc: stable@vger.kernel.org
Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com>
Reviewed-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Link: https://lore.kernel.org/r/20260603105317.944304-3-dawei.feng@seu.edu.cn
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f73aa66dff upstream.
The bdev pseudo-filesystem is an internal kernel filesystem with which
userspace should not interfere. Unregister it so that userspace cannot
even attempt to mount it.
This fixes a bug [1] that occurs when attempting to access files,
because the system call move_mount() uses pointers declared in the
inode_operations structure, which for the bdev pseudo-filesystem
are always equal to 0. `inode->i_op = &empty_iops;`
[1]
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0010) - not-present page
PGD 23380067 P4D 23380067 PUD 23381067 PMD 0
Oops: 0010 [#1] PREEMPT SMP KASAN NOPTI
CPU: 2 PID: 17125 Comm: syz-executor.0 Not tainted 6.1.155-syzkaller-00350-g84221fde2681 #0
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
RIP: 0010:0x0
Call Trace:
<TASK>
lookup_open.isra.0+0x700/0x1180 fs/namei.c:3460
open_last_lookups fs/namei.c:3550 [inline]
path_openat+0x953/0x2700 fs/namei.c:3780
do_filp_open+0x1c5/0x410 fs/namei.c:3810
do_sys_openat2+0x171/0x4d0 fs/open.c:1318
do_sys_open fs/open.c:1334 [inline]
__do_sys_openat fs/open.c:1350 [inline]
__se_sys_openat fs/open.c:1345 [inline]
__x64_sys_openat+0x13c/0x1f0 fs/open.c:1345
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x35/0x80 arch/x86/entry/common.c:81
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/all/20131010004732.GJ13318@ZenIV.linux.org.uk/T/#
Cc: stable@vger.kernel.org
Signed-off-by: Denis Arefev <arefev@swemel.ru>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260521072857.5078-1-arefev@swemel.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d874b65aa upstream.
A partial atomic write reserves a block in the COW inode before reading the
original data page for the untouched bytes in that page.
If that read fails, write_begin returns an error but leaves the COW inode
entry as NEW_ADDR. A retry of the same partial write then finds the COW
entry, treats it as existing COW data, and f2fs_write_begin() zeroes the
whole folio because blkaddr is NEW_ADDR.
If the retry is committed, the bytes outside the retried write range are
committed as zeroes instead of preserving the original file contents.
Only use the COW inode as the read source when it already has a real data
block. If the COW entry is still NEW_ADDR, treat it as a reservation to
reuse: keep reading the old data from the original inode and avoid
reserving or accounting the same atomic block again.
Cc: stable@kernel.org
Fixes: 3db1de0e58 ("f2fs: change the current atomic write way")
Signed-off-by: Wenjie Qi <qiwenjie@xiaomi.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f70ddb28a upstream.
When __destroy_extent_node() sets the inode flag FI_NO_EXTENT, it does
not reset the length of the largest extent to 0 and update the inode
folio. Since modifications to the extent tree are disallowed afterward,
the cached largest extent may become stale. This can trigger the
following error in xfstests generic/388:
F2FS-fs (dm-0): sanity_check_extent_cache: inode (ino=1761) extent info [220057, 57, 6] is incorrect, run fsck to fix
In the f2fs_drop_inode path, __destroy_extent_node() does not need to
guarantee that et->node_cnt is 0, because concurrency with writeback
is expected in this path, and writeback may update the extent cache.
This patch reverts commit ed78aeebef ("f2fs: fix node_cnt race between
extent node destroy and writeback"), and remove the unnecessary zero
check of et->node_cnt.
Fixes: ed78aeebef ("f2fs: fix node_cnt race between extent node destroy and writeback")
Cc: stable@vger.kernel.org
Reported-by: Chao Yu <chao@kernel.org>
Suggested-by: Chao Yu <chao@kernel.org>
Signed-off-by: Yongpeng Yang <yangyongpeng@xiaomi.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4810ada31 upstream.
f2fs_acl_count() only validates the aggregate ACL xattr length. A
malformed ACL can still place ACL_USER or ACL_GROUP in a slot that only
contains struct f2fs_acl_entry_short bytes, and f2fs_acl_from_disk()
then reads entry->e_id before verifying that a full entry fits.
Require a short entry before reading e_tag and e_perm, and require a
full entry before reading e_id for ACL_USER and ACL_GROUP. Return
-EFSCORRUPTED from these new truncated-entry checks, while keeping the
pre-existing -EINVAL paths unchanged.
Validation reproduced this kernel report:
KASAN slab-out-of-bounds in __f2fs_get_acl+0x6fb/0x7e0
RIP: 0033:0x7f4b835ea7aa
The buggy address belongs to the object at ffff888114589960 which belongs
to the cache kmalloc-8 of size 8
The buggy address is located 0 bytes to the right of allocated 8-byte
region [ffff888114589960, ffff888114589968)
Read of size 4
Call trace:
dump_stack_lvl+0x66/0xa0 (?:?)
print_report+0xce/0x630 (?:?)
__f2fs_get_acl+0x6fb/0x7e0 (fs/f2fs/acl.c:169)
srso_alias_return_thunk+0x5/0xfbef5 (?:?)
__virt_addr_valid+0x224/0x430 (?:?)
kasan_report+0xe0/0x110 (?:?)
__f2fs_get_acl+0x5/0x7e0 (fs/f2fs/acl.c:169)
__get_acl+0x281/0x380 (?:?)
vfs_get_acl+0x10b/0x190 (?:?)
do_get_acl+0x2a/0x410 (?:?)
do_get_acl+0x9/0x410 (?:?)
do_getxattr+0xe8/0x260 (?:?)
filename_getxattr+0xd1/0x140 (?:?)
do_getname+0x2d/0x2d0 (?:?)
path_getxattrat+0x16c/0x200 (?:?)
lock_release+0xc8/0x290 (?:?)
cgroup_update_frozen+0x9d/0x320 (?:?)
lockdep_hardirqs_on_prepare+0xea/0x1a0 (?:?)
trace_hardirqs_on+0x1a/0x170 (?:?)
_raw_spin_unlock_irq+0x28/0x50 (?:?)
do_syscall_64+0x115/0x6a0 (arch/x86/entry/syscall_64.c:87)
entry_SYSCALL_64_after_hwframe+0x77/0x7f (?:?)
Cc: stable@kernel.org
Fixes: af48b85b8c ("f2fs: add xattr and acl functionalities")
Assisted-by: Codex:gpt-5.5
Signed-off-by: Zhang Cen <rollkingzzc@gmail.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4275b59673 upstream.
Currently, the length of fallocate for pin file is section-aligned to
keep allocated sections from being selected as victims of GC. However,
for the case that the start offset of fallocate is not aligned in
section, the allocated sections can't be fully utilized. It's because a
new section is allocated by f2fs_allocate_pinning_section() after using
blks_per_sec blocks regardless of the start offset. As a result, several
unexpected dirty segments may be created, including blocks assigned to
the pinned file.
To address this issue, let's round down the start offset of fallocate
to the length of section.
The reproducing scenario is as below
chunk=$(((2<<20)+4096)) # 2MB + 4KB
touch test
f2fs_io pinfile set test
f2fs_io fallocate 0 0 $chunk test
f2fs_io fallocate 0 $chunk $chunk test
f2fs_io fallocate 0 $((chunk*2)) $chunk test
f2fs_io fiemap 0 $((chunk*3)) test
Fiemap: offset = 0 len = 12288
logical addr. physical addr. length flags
0 0000000000000000 000000068c600000 0000000000400000 00001088
1 0000000000400000 000000003d400000 0000000000001000 00001088
2 0000000000401000 00000003eb200000 0000000000200000 00001088
3 0000000000601000 00000005e4200000 0000000000001000 00001088
4 0000000000602000 0000000605400000 0000000000200000 00001089
Cc: stable@vger.kernel.org
Fixes: f5a53edcf0 ("f2fs: support aligned pinned file")
Reviewed-by: Yunji Kang <yunji0.kang@samsung.com>
Reviewed-by: Yeongjin Gil <youngjin.gil@samsung.com>
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Sunmin Jeong <s_min.jeong@samsung.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5073c66a96 upstream.
F2FS_COMPRESS_INO() uses NM_I(sbi)->max_nid as the synthetic inode
number for the compressed page cache inode. That inode only exists when
the compress_cache mount option is enabled.
When compress_cache is disabled, max_nid is outside the valid inode
range. A corrupted directory entry that points to ino == max_nid should
therefore be rejected by f2fs_check_nid_range(). However, is_meta_ino()
currently treats F2FS_COMPRESS_INO() as a meta inode unconditionally,
so f2fs_iget() bypasses do_read_inode() and its nid range check, and
instantiates a fake internal inode instead.
Gate the compressed cache inode case on COMPRESS_CACHE, matching
f2fs_init_compress_inode(). With compress_cache disabled, ino ==
max_nid now follows the normal inode path and is rejected as an
out-of-range nid.
Cc: stable@kernel.org
Fixes: 6ce19aff0b ("f2fs: compress: add compress_inode to cache compressed blocks")
Signed-off-by: Wenjie Qi <qiwenjie@xiaomi.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 846c499a65 upstream.
f2fs_recover_orphan_inodes() trusts the orphan block entry_count when
replaying orphan inodes from the checkpoint pack. A corrupted entry_count
larger than F2FS_ORPHANS_PER_BLOCK makes the recovery loop read past the
ino[] array and interpret footer or following data as inode numbers.
On a crafted image, mounting an unpatched kernel can drive orphan recovery
into f2fs_bug_on() and panic the kernel. Validate entry_count before
consuming entries so corrupted checkpoint data fails the mount with
-EFSCORRUPTED and requests fsck instead.
Set ERROR_INCONSISTENT_ORPHAN as well, so the corruption reason can be
recorded in the superblock s_errors[] field. This gives fsck a persistent
hint even though mount-time orphan recovery failure may leave no chance to
persist SBI_NEED_FSCK through a checkpoint.
Cc: stable@kernel.org
Fixes: 127e670abf ("f2fs: add checkpoint operations")
Signed-off-by: Wenjie Qi <qiwenjie@xiaomi.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcb05c26c2 upstream.
f2fs_write_single_node_folio() takes an io_type argument, but still
passes FS_GC_NODE_IO to __write_node_folio() unconditionally.
This was harmless while the helper was only used by
f2fs_move_node_folio(), whose caller passes FS_GC_NODE_IO. However,
commit fe9b8b30b9 ("f2fs: fix inline data not being written to disk
in writeback path") made f2fs_inline_data_fiemap() call the helper with
FS_NODE_IO for FIEMAP_FLAG_SYNC.
Honor the caller supplied io_type so inline-data FIEMAP sync writeback is
accounted as normal node IO instead of GC node IO, while the GC path
continues to pass FS_GC_NODE_IO explicitly.
Cc: stable@kernel.org
Fixes: fe9b8b30b9 ("f2fs: fix inline data not being written to disk in writeback path")
Signed-off-by: Wenjie Qi <qiwenjie@xiaomi.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b964941bb upstream.
When rtw_usb_write_port() fails to submit a USB Request Block (URB)
(e.g., due to device disconnect or ENOMEM), the completion callback is
never executed.
Currently, the driver ignores the return value of rtw_usb_write_port()
in rtw_usb_write_data() and rtw_usb_tx_agg_skb(). Because these
functions rely on the completion callback to free the socket buffers
(skbs) and the transaction control block (txcb), a submission failure
results in:
1. A memory leak of the allocated skb in rtw_usb_write_data().
2. A memory leak of the txcb structure and all aggregated skbs in
rtw_usb_tx_agg_skb().
Fix this by checking the return value of rtw_usb_write_port(). If it
fails, explicitly free the skb in rtw_usb_write_data(), and properly
purge the tx_ack_queue and free the txcb in rtw_usb_tx_agg_skb().
The issue was discovered in practice during device disconnect/reconnect
scenarios and memory pressure conditions. Tested by verifying normal TX
operation continues after the fix without regressions.
Fixes: a82dfd33d1 ("wifi: rtw88: Add common USB chip support")
Cc: stable@vger.kernel.org
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Luka Gejak <luka.gejak@linux.dev>
Signed-off-by: Luka Gejak <luka.gejak@linux.dev>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260518142311.10328-2-luka.gejak@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c80788f7c5 upstream.
The driver expects the firmware to report TX status within 500ms.
However, a timeout can be triggered when the hardware performs
background scans while under TX load. During these scans, the firmware
stays off-channel for periods exceeding 500ms, delaying the delivery of
TX reports back to the driver.
When this occurs, the purge timer fires prematurely and drops the
tracking skbs from the queue. This results in the host stack
interpreting the missing status as packet loss, leading to TCP window
collapse. In testing with iperf3, this causes throughput to drop from
~90 Mbps to near-zero for approximately 2 seconds until the connection
recovers.
Increase RTW_TX_PROBE_TIMEOUT to 2500ms for RTL8723DU. This duration is
sufficient to accommodate off-channel dwell time during full background
scans, ensuring the purge timer only trips during genuine firmware
lockups and preventing unnecessary TCP retransmission cycles.
Fixes: a82dfd33d1 ("wifi: rtw88: Add common USB chip support")
Cc: stable@vger.kernel.org
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Luka Gejak <luka.gejak@linux.dev>
Signed-off-by: Luka Gejak <luka.gejak@linux.dev>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260518142311.10328-1-luka.gejak@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b7a26b668 upstream.
If there is an error during some initialization related to firmware,
the buffers dp->tx_ring[i].tx_status are released.
However this is released again when the device is unbinded (ath11k_pci),
and we get:
WARNING: CPU: 0 PID: 6231 at mm/slub.c:4368 free_large_kmalloc+0x57/0x90
Call Trace:
free_large_kmalloc
ath11k_dp_free
ath11k_core_deinit
ath11k_pci_remove
...
The issue is always reproducible from a VM because the MSI addressing
initialization is failing.
In order to fix the issue, just set the buffers to NULL after releasing in
order to avoid the double free.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260420110130.509670-1-jtornosm@redhat.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37d65384aa upstream.
On a STATION vif, removing a TDLS peer takes the mt7925_mac_sta_remove
-> mt7925_mac_sta_remove_links path. The first loop in that function
calls mt7925_mcu_add_bss_info(..., enable=false) for every link of the
station being removed. For a non-MLO STATION vif there is exactly one
link, link 0, whose bss_conf is the AP's. TDLS peers do not have their
own bss_conf - they share the AP's BSS.
The result is that every TDLS peer teardown sends a BSS_INFO_UPDATE
with enable=0 for the AP's BSS to the firmware, which wipes the AP-side
rate-control context. The connection stays associated and TX from the
host still works at the negotiated rate, but the AP's downlink to us
collapses to the lowest mandatory OFDM rate (HE-MCS 0 / 6 Mbit/s OFDM)
and only slowly recovers as rate adaptation re-learns under sustained
traffic. With brief or bursty traffic the link can stay at 6-72 Mbit/s
indefinitely, requiring a manual reconnect.
mt7925_mac_link_sta_remove() already guards its own
mt7925_mcu_add_bss_info(..., false) call with
"vif->type == NL80211_IFTYPE_STATION && !link_sta->sta->tdls".
Add the equivalent guard at the top of the cleanup loop in
mt7925_mac_sta_remove_links(), above the link_sta / link_conf /
mlink / mconf lookups, so TDLS peer teardown skips the loop body
entirely without doing the per-link work that would just be thrown
away.
Verified on mt7925e by triggering Samsung-S938B auto-TDLS via iperf3
and watching iw rx bitrate after teardown:
Before: rx bitrate collapses to 6.0-72.0 Mbit/s, oscillates 17/72/
137/288/432 Mbit/s for 30+ seconds, no full recovery without
a manual reassoc.
After: rx bitrate stays at 1200.9 Mbit/s HE-MCS 11 NSS 2 80 MHz
across the entire TDLS lifecycle.
bpftrace confirms a single mt7925_mcu_add_bss_info(enable=0) call per
teardown before the fix; zero such calls after.
Fixes: 3878b43336 ("wifi: mt76: mt7925: update mt7925_mac_link_sta_[add, assoc, remove] for MLO")
Cc: stable@vger.kernel.org
Signed-off-by: ElXreno <elxreno@gmail.com>
Assisted-by: Claude:claude-opus-4-7 bpftrace
Link: https://patch.msgid.link/20260506-mt7925-tdls-fixes-v2-2-46aa826ba8bb@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd15b457a8 upstream.
A: request_key() B: KEYCTL_INSTANTIATE_IOV
================ =========================
create auth key
store rka in auth key
wait for helper
get auth key
load rka from auth key
copy user payload
sleep on #PF
helper completed
detach and free rka
destroy auth key
wake up
use rka->target_key
**USE-AFTER-FREE**
Give request_key_auth payloads a refcount. Take a payload reference while
authkey->sem stabilizes the payload and revocation state. Hold that
reference across the instantiate and reject paths. Drop the auth key
owning reference from revoke and destroy.
[jarkko: Replaced the first two paragraphs of text with an actual
concurrency scenario.]
Cc: stable@vger.kernel.org # v5.10+
Fixes: b5f545c880 ("[PATCH] keys: Permit running process to instantiate keys")
Reported-by: Shaomin Chen <eeesssooo020@gmail.com>
Closes: https://lore.kernel.org/r/20260519144403.436694-1-eeesssooo020@gmail.com
Signed-off-by: Shaomin Chen <eeesssooo020@gmail.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56cb9b7d96 upstream.
GCC's GCOV instrumentation can merge global branch counters with loop
induction variables as an optimization. In inflate_fast(), the inner copy
loops get transformed so that the GCOV counter value is loaded multiple
times to compute the loop base address, start index, and end bound. Since
GCOV counters are global (not per-CPU), concurrent execution on different
CPUs causes the counter to change between loads, producing inconsistent
values and out-of-bounds memory writes.
The crash manifests during IPComp (IP Payload Compression) processing when
inflate_fast() runs concurrently on multiple CPUs:
BUG: unable to handle page fault for address: ffffd0a3c0902ffa
RIP: inflate_fast+1431
Call Trace:
zlib_inflate
__deflate_decompress
crypto_comp_decompress
ipcomp_decompress [xfrm_ipcomp]
ipcomp_input [xfrm_ipcomp]
xfrm_input
At the crash point, the compiler generated three loads from the same
global GCOV counter (__gcov0.inflate_fast+216) to compute base, start, and
end for an indexed loop. Another CPU modified the counter between loads,
making the values inconsistent - the write went 3.4 MB past a 65 KB
buffer.
Add -fprofile-update=prefer-atomic to CFLAGS_GCOV at the global level in
the top-level Makefile, guarded by a try-run compile test. The test
compiles a minimal program with and without -fprofile-update=prefer-atomic
using the full KBUILD_CFLAGS, then compares undefined symbols in the
resulting object files. If prefer-atomic introduces new undefined
references (such as __atomic_fetch_add_8 on i386 or __aarch64_ldadd8_relax
on arm64 with outline-atomics), the flag is not added -- the kernel does
not link against libatomic.
On architectures where GCC inlines 64-bit atomic counter updates (x86_64,
s390, ...) the test passes and the flag is enabled, preventing the
compiler from merging counters with loop induction variables and fixing
the observed concurrent-access crash.
On architectures where the flag would introduce libatomic dependencies, it
is silently omitted and behaviour is no worse than before this patch.
Move the CFLAGS_GCOV block from its original position (before the arch
Makefile include) to after the core KBUILD_CFLAGS assignments but before
the scripts/Makefile.gcc-plugins include. This placement ensures the
try-run test sees arch-specific flags (-m32, -march=,
-mno-outline-atomics) while avoiding GCC plugin flags (-fplugin=) that
would break the test on clean builds when plugin shared objects do not yet
exist.
Link: https://lore.kernel.org/20260511105052.417187-2-khorenko@virtuozzo.com
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Miguel Ojeda <ojeda@kernel.org>
Cc: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: Thomas Weißschuh <linux@weissschuh.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2986a62574 upstream.
Commit
f620d66af3 ("arm64: mte: Do not flag the zero page as PG_mte_tagged")
removed the PG_mte_tagged flag from the zero page, but missed a KVM code
path that may set this flag on the zero page when it is used in a
stage-2 CoW mapping of anonymous memory.
So disregard the zero page explicitly in sanitise_mte_tags().
Fixes: f620d66af3 ("arm64: mte: Do not flag the zero page as PG_mte_tagged")
Cc: stable@vger.kernel.org # 5.10.x
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fad156c2af upstream.
blk_time_get_ns() caches ktime_get_ns() in current->plug->cur_ktime
and marks the task with PF_BLOCK_TS. That cache is only valid while the
task keeps running; if the task is switched out, wall-clock time
advances and the cached value must not be reused when the task runs again.
The existing invalidation covers explicit plug flushes through
__blk_flush_plug(), and the schedule() / rtmutex paths through
sched_update_worker(). It does not cover in-kernel preemption paths such
as preempt_schedule(), preempt_schedule_notrace(), and
preempt_schedule_irq(), which enter __schedule(SM_PREEMPT) directly and
return without calling sched_update_worker().
As a result, a task preempted while holding a plug with PF_BLOCK_TS set
can reuse a stale plug->cur_ktime after it is scheduled back in. blk-iocost
then consumes that stale timestamp through ioc_now(), producing stale vnow
values for throttle decisions, and through ioc_rqos_done(), inflating
on-queue time and feeding false missed-QoS samples into vrate
adjustment.
Move the schedule-side invalidation to finish_task_switch(), which runs
for the scheduled-in task after every actual context switch regardless
of which schedule entry point was used. Keep __blk_flush_plug() as the
explicit flush/finish-plug invalidation path, and remove only the
PF_BLOCK_TS handling from sched_update_worker().
Fixes: 06b23f92af ("block: update cached timestamp post schedule/preemption")
Cc: stable@vger.kernel.org
Signed-off-by: Usama Arif <usama.arif@linux.dev>
Link: https://patch.msgid.link/20260616141604.328820-3-usama.arif@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd38b75c4b upstream.
PF_BLOCK_TS is only set in blk_time_get_ns() when current->plug is
non-NULL, and blk_finish_plug() clears it via __blk_flush_plug()
before NULLing the plug pointer. copy_process() breaks the
invariant by inheriting PF_BLOCK_TS from the parent while resetting
the child's plug to NULL.
Clear PF_BLOCK_TS alongside that assignment so callers can rely on
"PF_BLOCK_TS set implies current->plug != NULL" and dereference
current->plug unguarded.
Fixes: 06b23f92af ("block: update cached timestamp post schedule/preemption")
Cc: stable@vger.kernel.org
Signed-off-by: Usama Arif <usama.arif@linux.dev>
Link: https://patch.msgid.link/20260616141604.328820-2-usama.arif@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c1c805c65 upstream.
store_modes() replaces a framebuffer's modelist with modes from userspace.
On success it frees the old modelist with fb_destroy_modelist(). Two
fields still point into that freed list.
One pointer is fb_display[i].mode, the mode a console is using.
fbcon_new_modelist() moves these pointers to the new list. It only does so
for consoles still mapped to the framebuffer. An unmapped console is
skipped and keeps its stale pointer. Unbinding fbcon, for example, sets
con2fb_map[i] to -1 but leaves fb_display[i].mode set. An
FBIOPUT_VSCREENINFO ioctl with FB_ACTIVATE_INV_MODE later reaches
fbcon_mode_deleted(). That function reads the stale fb_display[i].mode
through fb_mode_is_equal(). The read is a use-after-free.
The other pointer is fb_info->mode, the current mode. It is set through
the mode sysfs attribute. store_modes() does not update fb_info->mode, so
it is left pointing into the freed list. show_mode(), the attribute's read
handler, dereferences the stale fb_info->mode through mode_string(). The
read is a use-after-free.
Clear both pointers before freeing the list. Commit a1f3058930 ("fbcon:
Set fb_display[i]->mode to NULL when the mode is released") added the
helper fbcon_delete_modelist(). It clears every fb_display[i].mode that
points into a given list. So far it is called only from the unregister
path. Call it from store_modes() too, and set fb_info->mode to NULL.
Reported-by: syzbot+81c7c6b52649fd07299d@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=81c7c6b52649fd07299d
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/ajjoDhAi2y4ArSlz@dev/
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Ian Bridges <icb@fastmail.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d876153680 upstream.
When BAR_PEER_SPAD and BAR_CONFIG share one PCI BAR, the module teardown
path ends up calling pci_iounmap() on the same iomem with some offset,
which is unnecessary and triggers a kernel warning like the following:
Trying to vunmap() nonexistent vm area (0000000069a5ffe8)
WARNING: mm/vmalloc.c:3470 at vunmap+0x58/0x68, CPU#5: modprobe/2937
[...]
Call trace:
vunmap+0x58/0x68 (P)
iounmap+0x34/0x48
pci_iounmap+0x2c/0x40
ntb_epf_pci_remove+0x44/0x80 [ntb_hw_epf]
pci_device_remove+0x48/0xf8
device_remove+0x50/0x88
device_release_driver_internal+0x1c8/0x228
driver_detach+0x50/0xb0
bus_remove_driver+0x74/0x100
driver_unregister+0x34/0x68
pci_unregister_driver+0x34/0xa0
ntb_epf_pci_driver_exit+0x14/0xfe0 [ntb_hw_epf]
[...]
Fix it by unmapping only when PEER_SPAD and CONFIG use difference bars.
Cc: stable@vger.kernel.org
Fixes: e75d5ae8ab ("NTB: epf: Allow more flexibility in the memory BAR map method")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f060496d0 upstream.
aa_replace_profiles() walks ns->rawdata_list to dedup the incoming
policy blob against entries already attached to existing profiles.
Per the kernel-doc on struct aa_loaddata, list membership does not
hold a reference: profiles hold pcount, and when the last pcount
drops, do_ploaddata_rmfs() is queued on a workqueue that takes
ns->lock and removes the entry. Between dropping the last pcount
and the workqueue running, an entry remains on the list with
pcount == 0.
aa_get_profile_loaddata() is an unconditional kref_get() on
pcount, so when the dedup loop hits such an entry, refcount
hardening reports
refcount_t: addition on 0; use-after-free.
inside aa_replace_profiles(), and the poisoned counter then
trips "saturated" and "underflow" warnings on the subsequent
uses of the same loaddata.
Before commit a0b7091c4d ("apparmor: fix race on rawdata
dereference") the dedup path used a get_unless_zero-style helper
on a single counter, so the existing "if (tmp)" guard was
meaningful. The split-refcount refactor introduced
aa_get_profile_loaddata(), which has plain kref_get() semantics,
and the guard quietly became a no-op.
Introduce aa_get_profile_loaddata_not0(), matching the existing
_not0 convention used by aa_get_profile_not0(), and use it for
the rawdata_list dedup lookup so dying entries are skipped.
Reproduced on x86_64 with v7.1-rc5 in QEMU+KVM running Ubuntu
24.04 + stress-ng 0.17.06:
stress-ng --apparmor 1 --klog-check --timeout 60s
Without this patch the three refcount_t warnings fire within a
few seconds. With it the same 60 s run is clean. Coverage is a
smoke-test only; a longer soak with CONFIG_KASAN, CONFIG_KCSAN
and CONFIG_PROVE_LOCKING would be welcome from anyone with the
cycles.
Fixes: a0b7091c4d ("apparmor: fix race on rawdata dereference")
Reported-by: Colin Ian King <colin.i.king@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221513
Cc: stable@vger.kernel.org
Signed-off-by: Ruslan Valiyev <linuxoid@gmail.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d587cd8a7 upstream.
sendmsg()/sendto() with MSG_FASTOPEN is a combination of connect(2) and
write(2): it opens the connection in the SYN. apparmor_socket_sendmsg()
only checks AA_MAY_SEND, so a profile that grants send but denies connect
lets a confined task open an outbound TCP/MPTCP connection that connect(2)
would have refused, bypassing connect mediation.
Mediate the implicit connect when MSG_FASTOPEN is set and a destination
is supplied. Add it to apparmor_socket_sendmsg() (not the shared
aa_sock_msg_perm() helper, which recvmsg also uses) and call aa_sk_perm()
directly, mirroring the selinux and tomoyo fixes. sk_is_tcp() does not
cover MPTCP fast open, so the SOCK_STREAM/IPPROTO_MPTCP arm is explicit.
Fixes: cf60af03ca ("net-tcp: Fast Open client - sendmsg(MSG_FASTOPEN)")
Cc: stable@vger.kernel.org
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8165f7ff57 upstream.
A tunnel changelink() operates on at most two netns, dev_net(dev) and
the tunnel link netns t->net. They differ once the device is created in
or moved to a netns other than the one the request runs in. The rtnl
changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a
caller privileged there but not in t->net can rewrite a tunnel that
lives in t->net.
Add rtnl_dev_link_net_capable() next to rtnl_get_net_ns_capable() in
net/core/rtnetlink.c. It requires CAP_NET_ADMIN in the link netns and is
skipped when the link netns is dev_net(dev), where the rtnl path already
checked it. The other patches in this series use the same helper.
Gate ipgre_changelink() and erspan_changelink() with it, at the top of
the op before any attribute is parsed, because the parsers update live
tunnel fields first. ipgre_netlink_parms() sets t->collect_md before
ip_tunnel_changelink() runs.
Commit 8b484efd5c ("ip6: vti: Use ip6_tnl.net in
vti6_siocdevprivate().") added the same check on the ioctl path. This
adds it on RTM_NEWLINK.
Reported-by: Xiao Liang <shaw.leon@gmail.com>
Closes: https://lore.kernel.org/netdev/CABAhCOSzP1vaThGV35_VnsRCb=87_CPjPVsTHbq905k8A+BuUg@mail.gmail.com/
Fixes: b57708add3 ("gre: add x-netns support")
Cc: stable@vger.kernel.org
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260612085941.3158249-2-maoyixie.tju@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 406e8a651a upstream.
The sk_msg sg.copy bitmap is part of the scatterlist entry ownership
state. A set bit tells sk_msg_compute_data_pointers() not to expose the
entry through writable BPF ctx->data. This protects entries backed by
pages that are not private to the sk_msg, such as splice-backed file
page-cache pages.
Several sk_msg transform paths move, copy, split, or compact
msg->sg.data[] entries without moving the matching sg.copy bit. This can
make an externally backed entry arrive at a new slot with a clear copy
bit. A later SK_MSG verdict can then expose sg_virt(sge) as writable
ctx->data and BPF stores can modify the original page cache.
Keep sg.copy synchronized with sg.data[] whenever entries are
transferred, shifted, split, or copied into a new sk_msg. Clear the bit
when an entry is replaced by a newly allocated private page or freed.
This covers the BPF pull/push/pop helpers, sk_msg_shift_left/right(),
sk_msg_xfer(), and tls_split_open_record(), including the partial tail
entry created during TLS open-record splitting.
Fixes: d3b18ad31f ("tls: add bpf support to sk_msg handling")
Cc: stable@vger.kernel.org
Reported-by: Yiming Qian <yimingqian591@gmail.com>
Reported-by: Keenan Dong <keenanat2000@gmail.com>
Signed-off-by: Yiming Qian <yimingqian591@gmail.com>
Link: https://patch.msgid.link/20260610062137.49075-1-yimingqian591@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84a04eb5b2 upstream.
llsec_do_encrypt_unauth(), llsec_do_encrypt_auth(),
llsec_do_decrypt_unauth(), and llsec_do_decrypt_auth() all perform
in-place cryptographic transformations on skb data. They build a
scatterlist with sg_init_one() pointing into the skb's linear data area
and then pass the same scatterlist as both src and dst to the crypto API
(e.g. crypto_skcipher_encrypt/decrypt, crypto_aead_encrypt/decrypt).
On the RX path, __ieee802154_rx_handle_packet() clones the received skb
before handing it to each subscriber via ieee802154_subif_frame(). The
cloned skb shares the same underlying data buffer via reference
counting. When llsec_do_decrypt() subsequently modifies this shared
buffer in place, it corrupts data that other clones -- potentially
belonging to other sockets or subsystems -- still reference.
On the TX path, similar data sharing can occur when an skb's head has
been cloned (skb_cloned() returns true).
The fix is to call skb_cow_data() before performing any in-place crypto
operation. skb_cow_data() ensures that the skb's data area is not
shared: if the skb head is cloned or the data spans multiple fragments,
it copies the data into a private buffer that can be safely modified in
place. This is the same pattern used by:
- ESP (net/ipv4/esp4.c, net/ipv6/esp6.c)
- MACsec (drivers/net/macsec.c)
- WireGuard (drivers/net/wireguard/receive.c)
- TIPC (net/tipc/crypto.c)
Without this guard, in-place crypto on shared skb data leads to:
- Silent data corruption of other skb clones
- Use-after-free when the crypto API scatterwalk writes through a
page that has already been freed by another clone's kfree_skb()
- Kernel crashes under concurrent 802.15.4 traffic with security
enabled (KASAN/KMSAN reports slab-use-after-free)
Found by 0sec (https://0sec.ai) using automated source analysis.
Fixes: 4c14a2fb5d ("mac802154: add llsec decryption method")
Fixes: 03556e4d0d ("mac802154: add llsec encryption method")
Cc: stable@vger.kernel.org
Reported-by: Doruk Tan Ozturk <doruk@0sec.ai>
Closes: https://lore.kernel.org/linux-wpan/20260525161806.96158-1-doruk@0sec.ai/
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Closes: <link to your mail on lore>
Link: https://lore.kernel.org/20260526183726.56100-1-doruk@0sec.ai
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d82ba05263 ]
Igor Ushakov reported that unix_gc() could run with gc_in_progress
being false if the work is scheduled while running:
Thread 1 Thread 2 Thread 3
-------- -------- --------
unix_schedule_gc() unix_schedule_gc()
`- if (!gc_in_progress) `- if (!gc_in_progress)
|- gc_in_progress = true |
`- queue_work() |
unix_gc() <----------------/ |
| |- gc_in_progress = true
... `- queue_work()
| |
`- gc_in_progress = false |
|
unix_gc() <---------------------------------------------'
|
... /* gc_in_progress == false */
|
`- gc_in_progress = false
unix_peek_fpl() relies on gc_in_progress not to confuse GC
by MSG_PEEK.
Let's set gc_in_progress to true in unix_gc().
Fixes: 8b90a9f819 ("af_unix: Run GC on only one CPU.")
Reported-by: Igor Ushakov <sysroot314@gmail.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260501073945.1884564-1-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ Add setting gc_in_progress in __unix_gc(). Keep the existing
set in unix_gc() for wait_for_unix_gc() over-limit throttling. ]
Signed-off-by: Igor Ushakov <sysroot314@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 20b126920a upstream.
Since mt7925_mac_sta_add publishes wcid, add publish check in mt76_sta_add
to avoid reinitializing the wcid->poll_list.
Found dev->sta_poll_list corruption when using mt7925 and 7.1-rc4.
According to the corruption information, prev->next was changed to itself.
wlan0: disconnect from AP 90:fb:5d:94:8b:e3 for new auth to 90:fb:5d:94:8b:e2
wlan0: authenticate with 90:fb:5d:94:8b:e2 (local address=84:9e:56:9c:7e:6b)
wlan0: send auth to 90:fb:5d:94:8b:e2 (try 1/3)
slab kmalloc-8k start ffff8c80958a6000 pointer offset 4160 size 8192
list_add corruption. prev->next should be next (ffff8c808a7488f8), but was ffff8c80958a7040. (prev=ffff8c80958a7040).
mt76_wcid_add_poll+0x95/0xd0 [mt76]
mt7925_mac_add_txs.part.0+0xa5/0xe0 [mt7925_common]
mt7925_rx_check+0xa7/0xc0 [mt7925_common]
mt76_dma_rx_poll+0x50d/0x790 [mt76]
mt792x_poll_rx+0x52/0xe0 [mt792x_lib]
Signed-off-by: Jiajia Liu <liujiajia@kylinos.cn>
Link: https://patch.msgid.link/20260528033814.46418-1-liujiajia@kylinos.cn
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b08dccecf upstream.
NTFS3 uses $LXUID, $LXGID, $LXMOD and $LXDEV as internal WSL
permission metadata and reloads them into i_uid, i_gid and i_mode
from ntfs_get_wsl_perm().
Because the empty-prefix xattr handler also lets file owners call
setxattr() on these names directly, an unprivileged writer on a
writable ntfs3 mount can plant root ownership and S_ISUID on their own
file and gain euid 0 after inode reload.
Reject direct userspace writes to the reserved $LX* names. Internal
ntfs3 metadata updates are unchanged because ntfs_save_wsl_perm()
writes them via ntfs_set_ea() directly.
Signed-off-by: Zhen Yan <sdjasjbuaa@gmail.com>
[almaz.alexandrovich@paragon-software.com: added an additional check for non privileged users]
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eca856950f ]
In __ip_append_data(), when the paged-allocation branch is taken,
alloclen and pagedlen are computed as
alloclen = fragheaderlen + transhdrlen;
pagedlen = datalen - transhdrlen;
datalen already includes fraggap, but the fraggap bytes carried over
from the previous skb are copied into the new skb's linear area at
offset transhdrlen by the subsequent skb_copy_and_csum_bits(). The
linear area is therefore undersized by fraggap bytes while pagedlen is
overstated by the same amount.
The non-paged branch sets alloclen to fraglen, which already accounts
for fraggap because datalen does. Bring the paged branch in line by
adding fraggap to alloclen and subtracting it from pagedlen.
After this adjustment, copy no longer collapses to -fraggap on the
paged path, so remove the stale comment describing that old arithmetic.
Fixes: 8eb77cc739 ("ipv4: avoid partial copy for zc")
Signed-off-by: Jungwoo Lee <jwlee2217@gmail.com>
Signed-off-by: Wongi Lee <qw3rtyp0@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/ajFR1eLAIs42TN3g@DESKTOP-19IMU7U.localdomain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 736b380e28 upstream.
In __ip6_append_data(), when the paged-allocation branch is taken
(MSG_MORE / NETIF_F_SG / large fraglen), alloclen and pagedlen are
computed as
alloclen = fragheaderlen + transhdrlen;
pagedlen = datalen - transhdrlen;
datalen already includes fraggap (datalen = length + fraggap). When
fraggap is non-zero, this is not the first skb and transhdrlen is zero.
The fraggap bytes carried over from the previous skb are copied just past
the fragment headers in the new skb's linear area. The linear area is
therefore undersized by fraggap bytes while pagedlen is overstated by the
same amount, and the copy writes past skb->end into the trailing
skb_shared_info.
An unprivileged user can trigger this via a UDPv6 socket using
MSG_MORE together with MSG_SPLICE_PAGES.
The bad accounting was introduced by commit 773ba4fe91 ("ipv6:
avoid partial copy for zc"). Before commit ce650a1663 ("udp6: Fix
__ip6_append_data()'s handling of MSG_SPLICE_PAGES"), the negative
copy value caused -EINVAL to be returned. That later commit allowed
MSG_SPLICE_PAGES to proceed in this case, making the corruption
triggerable.
The non-paged branch sets alloclen to fraglen, which already accounts
for fraggap because datalen does. Bring the paged branch in line by
adding fraggap to alloclen and subtracting it from pagedlen.
After this adjustment, copy no longer collapses to -fraggap on the
paged path, so remove the stale comment describing that old arithmetic.
Since a negative copy is no longer expected for a valid MSG_SPLICE_PAGES
case, remove the MSG_SPLICE_PAGES exception from the negative copy check.
Fixes: 773ba4fe91 ("ipv6: avoid partial copy for zc")
Signed-off-by: Jungwoo Lee <jwlee2217@gmail.com>
Signed-off-by: Wongi Lee <qw3rtyp0@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/ajFTqRljatR17fFy@DESKTOP-19IMU7U.localdomain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edb557b2ba upstream.
TVLV handlers can have the flag BATADV_TVLV_HANDLER_OGM_CIFNOTFND set to
signal that the OGM handler should be called (with NULL for data) when the
specific TVLV container was not found in the OGM. This is used by:
* DAT
* GW
* Multicast (OGM + Tracker)
The state whether the handler was executed was stored in the struct
batadv_tvlv_handler. But the TVLV processing is started without any lock.
Multiple parallel contexts processing TVLVs would therefore overwrite each
others BATADV_TVLV_HANDLER_OGM_CALLED flag in the shared
batadv_tvlv_handler.
Drop the shared BATADV_TVLV_HANDLER_OGM_CALLED flag and instead determine,
per TVLV buffer, whether a matching container was present by scanning the
packet's buffer.
Cc: stable@kernel.org
Fixes: ef26157747 ("batman-adv: tvlv - basic infrastructure")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 32a6799255 upstream.
The fields of an aggregated OGM(v2) are accessed assuming (at least) 2-byte
alignment, so a following OGM must start at an even offset. As the header
length is even, an odd tvlv_len would misalign it and trigger unaligned
accesses on strict-alignment architectures.
Such a misaligned TVLV/OGM/OGMv2 is not created by a normal participant in
the mesh. Therefore, reject such malformed packets.
Cc: stable@kernel.org
Fixes: ef26157747 ("batman-adv: tvlv - basic infrastructure")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 20d7658b74 upstream.
The local hash of DAT entries is supposed to be VLAN (VID) aware. But
the adding to the hash and the search in the hash were not checking the VID
information of the hash entries. The entries would therefore only be
correctly separated when batadv_hash_dat() didn't select the same buckets
for different VIDs.
Cc: stable@kernel.org
Fixes: be1db4f661 ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Michal Koutný
Fan Wu
Wentao Liang
Tristan Madani
Sam James
Sean Christopherson
Michael Bommarito
Maciej W. Rozycki
Dawei Feng
Denis Arefev
Wenjie Qi
Yongpeng Yang
Zhang Cen
Sunmin Jeong
Junrui Luo
Junjie Cao
Luka Gejak
Bitterblue Smith
Jose Ignacio Tornos Martinez
ElXreno
Zenm Chen
Mike Rapoport (Microsoft)
Shaomin Chen
Jarkko Sakkinen
Konstantin Khorenko
Arnd Bergmann
Ard Biesheuvel
Usama Arif
Ian Bridges
Koichiro Den
Ruslan Valiyev
Bryam Vargas
Maoyi Xie
Yiming Qian
Doruk Tan Ozturk
Kuniyuki Iwashima
Jiajia Liu
Konstantin Komarov
Wongi Lee
Sven Eckelmann