[ Upstream commit 438ece0618 ]
filename__write_int() formats an integer into a 64-byte buffer with
sprintf() then passes sizeof(buf) (64) as the write length. This
writes all 64 bytes including uninitialized stack data past the
formatted string. Most sysfs files reject the oversized write,
making the function always return -1.
Fix by capturing the sprintf() return value and using it as the
write length.
Reported-by: sashiko-bot <sashiko-bot@kernel.org>
Fixes: 3b00ea9386 ("tools lib api fs: Add sysfs__write_int function")
Cc: Kan Liang <kan.liang@intel.com>
Assisted-by: Claude:claude-opus-4.6
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52b1f96784 ]
filename__read_int() passes a stack buffer to read() using the full
sizeof(line) and then hands it to atoi() without null-terminating.
If a sysfs file fills the 64-byte buffer exactly, atoi() reads past
the array into uninitialized stack memory.
filename__read_ull_base() has the same issue with strtoull().
Fix both by reading sizeof(line) - 1 bytes and explicitly
null-terminating after a successful read.
Fixes: 3a351127cb ("tools lib fs: Adopt filename__read_int from tools/perf/")
Reported-by: sashiko-bot <sashiko-bot@kernel.org>
Assisted-by: Claude:claude-opus-4.6
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60e7870052 ]
rpcrdma_prepare_send_sges() gets a sendctx before it maps the SGEs
for the Send WR. If one of the mapping helpers fails, no Send WR
is posted, so no Send completion is guaranteed to advance rb_sc_tail.
Current cleanup clears sc_req so a later completion can sweep over
that slot, but a consecutive run of preparation failures can still
advance rb_sc_head until the ring appears full. At that point
rpcrdma_sendctx_get_locked() returns NULL and no Send can be posted to
produce the completion needed to recover the ring.
The trigger requires CONFIG_SUNRPC_XPRT_RDMA and an NFS/RDMA mount.
Mount setup and reliable DMA-map fault injection require local admin
authority. Unprivileged I/O on an existing mount can exercise the send
path, but a remote peer alone cannot force this local DMA-map failure.
Add rpcrdma_sendctx_unget_locked() for the single-consumer send path
to rewind rb_sc_head when the just-acquired sendctx is canceled before
ib_post_send(). Wake waiters after making the slot available again.
After the rewind, every slot the completion sweep visits belongs to a
posted Send, so rpcrdma_sendctx_put_locked() no longer needs to test
sc_req before unmapping.
Fixes: ae72950abf ("xprtrdma: Add data structure to manage RDMA Send arguments")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abc011ddaf ]
rpcrdma_wc_receive() decrements the transport's Receive count for
every completion before it dispatches a successful Receive to
rpcrdma_reply_handler(). The handler must post a replacement
Receive WR before returning unless ownership of the rep has moved
elsewhere, as on the backchannel path.
Commit 2ae50ad68c ("xprtrdma: Close window between waking RPC
senders and posting Receives") moved the Receive refill out of
rpcrdma_wc_receive(), where it had run ahead of every reply, into
rpcrdma_reply_handler() so that the responder's credit grant could
be parsed before reposting. The bad-version and short-reply exits
never reach that refill: they recycle the rep and return without
calling rpcrdma_post_recvs().
A remote peer can therefore drain the client's posted Receive
queue by sending a sustained stream of replies that are shorter
than the fixed transport header or that carry an unrecognized
RPC/RDMA version. Each such reply consumes one posted Receive
without replacing it. Once the queue empties, the peer's next
Send finds no posted Receive and the transport stalls until
reconnect.
Route both malformed-reply exits through the shared repost tail
after recycling the rep, refilling against buf->rb_credits, the
most recent accepted credit grant. Neither exit updates the
congestion window, so RPCs admitted under the previous grant
remain in flight awaiting replies. A smaller refill target would
let a stream of malformed replies ratchet the posted Receive count
down to the batch floor while the congestion window still admits
rb_credits RPCs; a burst of valid replies to those RPCs could then
overrun the posted Receives, and because the client connects with
rnr_retry_count of zero, a single RNR NAK terminates the
connection. Refilling against rb_credits also restores the target
that applied to malformed replies before commit 2ae50ad68c
("xprtrdma: Close window between waking RPC senders and posting
Receives") when rpcrdma_post_recvs() computed it from rb_credits
internally. rb_credits is at least one from connection
establishment onward, so the repost path always keeps Receives
posted.
Fixes: 2ae50ad68c ("xprtrdma: Close window between waking RPC senders and posting Receives")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3a628aab2 ]
The out_norqst exit in rpcrdma_reply_handler() branches away before
the credit clamp, so a reply that matches no pending request reaches
out_post carrying the raw credit value parsed from the wire.
rpcrdma_post_recvs() does not bound its @needed argument: the refill
loop allocates and chains Receive WRs until the count is satisfied or
allocation fails. A peer that sends a well-formed reply carrying an
unknown XID and an inflated credit grant therefore drives rep
allocation and Receive posting past re_max_requests on every such
reply.
Move the clamp to immediately after the credit field is parsed,
ahead of the first branch that can reach out_post, so every later
consumer sees a sanitized value. The cwnd update stays on the
matched-request path.
Fixes: 704f3f640f ("xprtrdma: Post receive buffers after RPC completion")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7653d5ceb ]
rpcrdma_is_bcall() decodes a reply's first words to decide whether
the frame is a backchannel call. Two issues in that decode path
let a short or malformed reply leak the receive buffer and drain
the Receive queue.
First, the speculative peek
p = xdr_inline_decode(xdr, 0);
/* five p++ reads follow */
asks xdr_inline_decode() for zero bytes, which returns xdr->p
without consulting xdr->end. The five subsequent __be32 reads can
then walk up to 20 bytes past the wire payload into stale regbuf
contents and misclassify the reply as a backchannel call.
Second, after the post-peek
p = xdr_inline_decode(xdr, 3 * sizeof(*p));
if (unlikely(!p))
return true;
the short-header arm returns true without calling
rpcrdma_bc_receive_call(). The contract with the caller is that a
true return transfers ownership of rep to the backchannel path:
rpcrdma_reply_handler()
if (rpcrdma_is_bcall(r_xprt, rep))
return; /* bare return, skips out_post */
...
out_post:
rpcrdma_post_recvs(r_xprt, credits + ...);
Because rpcrdma_bc_receive_call() never ran, no one took rep, but
rpcrdma_reply_handler still bare-returns past rpcrdma_rep_put()
and rpcrdma_post_recvs(). The rep, with its persistently
DMA-mapped receive buffer, is orphaned on rb_all_reps and freed
only at transport teardown. This completion reposts nothing, so
its slot is reclaimed only when a later forward-channel reply
reaches out_post and rpcrdma_post_recvs() allocates a fresh rep to
backfill; absent that traffic the Receive queue drains and the
peer's Sends draw RNR NAKs.
Fix by consulting xdr->end after the zero-length peek so the five
__be32 reads cannot run unless 20 bytes of wire payload remain. A
byte-precise comparison against xdr->end is required because a
non-4-aligned receive rounds the stream's word count up past the
true payload. Also return false from the short-header arm so the
reply falls through the normal out_norqst cleanup chain
(rpcrdma_rep_put() plus rpcrdma_post_recvs()).
Fixes: 41c8f70f5a ("xprtrdma: Harden backchannel call decoding")
Assisted-by: kres:claude-opus-4-7
Signed-off-by: Chris Mason <clm@meta.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 234c0ff695 ]
Commit 0e13dd9ea8 ("xprtrdma: Remove temp allocation of
rpcrdma_rep objects") made rpcrdma_rep objects survive disconnects.
That is normally fine, but it also means their receive regbufs keep
the size they had when they were first allocated.
Each rep's receive buffer is sized to ep->re_inline_recv when the rep
is created. rpcrdma_ep_create() resets that threshold to the
rdma_max_inline_read ceiling for every new endpoint, and the connect
handshake then shrinks it to the peer's advertised inline send size.
A rep allocated under a smaller negotiated threshold keeps that size:
on disconnect, rpcrdma_xprt_disconnect() drains and DMA-unmaps the
surviving reps but does not free or resize them.
The threshold can come back larger on the next connection. The first
peer may supply no RPC-over-RDMA CM private data, defaulting its send
size to 1024, while the reconnect target is an ordinary server
offering 4096; or, with rdma_max_inline_read raised above its default,
the reconnect target may advertise a larger svcrdma_max_req_size than
the first. rpcrdma_post_recvs() then reposts a surviving rep whose SGE
length is still the old, smaller value, and a larger inline Reply hits
a receive length error and forces another disconnect.
The undersized rep returns to the free list when its failed Receive
flushes, so the following reconnect reposts the same rep and fails the
same way. The transport flaps without making forward progress for as
long as the peer keeps advertising the larger inline size.
This is local/admin-triggerable rather than remote-triggerable: a local
administrator must create and maintain the NFS/RDMA mount, while the
server or reconnect target has to advertise a larger inline send size
and return a reply that uses it.
Fix this by checking each rep before it is reposted. If the receive
regbuf is smaller than the current endpoint's inline receive size,
reallocate it on the current RDMA device's NUMA node and reinitialize
the rep's xdr_buf before DMA-mapping and posting the Receive WR.
Fixes: 0e13dd9ea8 ("xprtrdma: Remove temp allocation of rpcrdma_rep objects")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 797943e8bd ]
The xprtrdma reply path has been the subject of recurring
LLM-driven review claims that 'an RPC can complete while
receive buffers are still DMA-mapped' or that 'the req can be
freed while the HCA still owns the send buffer.' No runtime
reproducer has surfaced, but the absence of a written-down
invariant set lets each pass of automated review reach the
same hypothetical conclusion. Subsequent fixes against
ce2f9a4d9ccc ('xprtrdma: Decouple req recycling from RPC
completion') closed the underlying races but did not document
the closure where future readers will look for it.
State the invariants explicitly in a comment above
rpcrdma_reply_handler() and back four of them with
WARN_ON_ONCE() probes positioned where each invariant is
locally checkable on the previous patch's cleaned-up
ownership state:
- I1 (Receive WR ownership): WARN at rpcrdma_post_recvs() that
a rep pulled from rb_free_reps carries rr_rqst == NULL.
- I2 (rep attachment): WARN at rpcrdma_reply_put() that
req->rl_reply was NULLed before the matching rep_put.
- I3 (Registered-MR fence): WARN at rpcrdma_complete_rqst()
that req->rl_registered is empty. Strong send-queue
ordering of the LocalInv WR chain makes the last
completion observe the ib_dma_unmap_sg() of every earlier
MR, so 'list empty' implies 'all MRs unmapped'.
- I4 (Send-buffer release): WARN at rpcrdma_req_release()
that req->rl_sendctx is NULL. Reaching the kref release
callback requires both the RPC-layer and Send-side
references to have dropped; the Send-side drop runs in
rpcrdma_sendctx_unmap(), which clears rl_sendctx
(previous patch). A non-NULL rl_sendctx here would mean
the Send-side owner had not run -- a contradiction.
The XXX comment in xprt_rdma_free() about signal-driven
release racing the Send completion described the pre-decouple
state. Replace it with a one-line note pointing at the
invariant set, since the kref scheme now holds the req across
the in-flight Send regardless of which path released the
rpc_task.
I5 (req lifecycle) is stated in the comment but not probed:
making it locally assertible would require moving kref_init
out of rpcrdma_req_release(), which in turn requires adding
kref_init to the bc_pa_list and backlog-wake reuse paths.
That restructuring is deferred -- the invariant is unchanged
either way.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Stable-dep-of: 234c0ff695 ("xprtrdma: Resize reply buffers before reposting receives")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f13fc7c7d ]
frwr_wp_create() creates the singleton Memory Region used to encode
padding for Write chunks whose payload length is not XDR-aligned. Its
failure paths return a negative errno and leave ep->re_write_pad_mr set
to NULL.
rpcrdma_xprt_connect() currently ignores that return value. If
frwr_wp_create() fails after the rest of the connection setup succeeds,
xprt_rdma_connect_worker() treats the connection attempt as successful
and sets XPRT_CONNECTED. A later NFS/RDMA read with a non-4-byte-aligned
receive page length reaches rpcrdma_encode_write_list(), passes the NULL
write-pad MR to encode_rdma_segment(), and dereferences it.
This is locally triggerable on an NFS/RDMA client after a connect or
reconnect hits a local MR allocation, DMA-map, MR-map, or post-send
failure; a remote peer alone cannot force the local MR setup failure.
Check the return value and fail the connect as -ENOTCONN, matching the
adjacent setup failures. This keeps XPRT_CONNECTED clear and lets the
normal reconnect path retry.
Fixes: 21037b8c22 ("xprtrdma: Provide a buffer to pad Write chunks of unaligned length")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a35454179 ]
log_replay() allocates log->one_page_buf using the page size that was
chosen from the host PAGE_SIZE:
log->one_page_buf = kmalloc(log->page_size, GFP_NOFS);
Later, when a restart area is found, the log page size recorded on disk
is adopted:
t32 = le32_to_cpu(log->rst_info.r_page->sys_page_size);
if (log->page_size != t32) {
log->l_size = log->orig_file_size;
log->page_size = norm_file_page(t32, &log->l_size,
t32 == DefaultLogPageSize);
}
If the on-disk page size is larger than the size used for the initial
allocation, log->page_size grows but one_page_buf is left at its
original, smaller size. A subsequent unaligned read_log_page() then
reads log->page_size bytes into the undersized scratch buffer:
page_buf = page_off ? log->one_page_buf : *buffer;
err = ntfs_read_run_nb_ra(ni->mi.sbi, &ni->file.run, page_vbo, page_buf,
log->page_size, NULL, &log->read_ahead);
overflowing the allocation. This is reachable when mounting a dirty
NTFS volume whose log was formatted with a page size larger than the
buffer initially allocated on the mounting host (for example a 64K-log
volume mounted on a host that allocated a 4K scratch buffer).
Grow one_page_buf when the adopted on-disk page size exceeds the size
used for the initial allocation. On krealloc() failure the original
buffer is left intact and freed by the existing error path.
Fixes: b46acd6a6a ("fs/ntfs3: Add NTFS journal")
Reported-by: Carol L Soto <csoto@nvidia.com>
Signed-off-by: Jamie Nguyen <jamien@nvidia.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b12341b98d ]
meson_pcie_probe_clock() enables a clock and then registers a devres
action to disable it during teardown. If devm_add_action_or_reset()
fails, it runs the action immediately, disabling the clock.
The return value is currently ignored, so on that failure path,
meson_pcie_probe_clock() returns the disabled clock and probe continues.
Return the error so the existing probe error path unwinds normally.
Fixes: 9c0ef6d34f ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Shuvam Pandey <shuvampandey1@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/177909148011.9588.6639767953842842291@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 282305d7e9 ]
The original PCIE_FTS_NUM_L0(x) macro was buggy due to improper operator
precedence, where ((x) & 0xff << 8) was evaluated as ((x) & 0xff00).
Instead of just fixing the parentheses, use the standard FIELD_PREP()
macro. This makes the code more robust by automatically handling masks
and shifts, while also adding compile-time type and range checking to
ensure the value fits within PCIE_FTS_NUM_MASK.
Fixes: 637cfacae9 ("PCI: mediatek: Add MediaTek PCIe host controller support")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
[mani: added the bitfield header include spotted by Sashiko]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://patch.msgid.link/20260515005552.2343-1-lirongqing@baidu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d62e659c0 ]
The FF_FLAGS_NO_IO_THRU_MDS flag lives on each lseg, so any fallback
decision made when there is no current lseg (e.g. between LAYOUTRETURN
and the next LAYOUTGET) cannot run the per-lseg check.
Introduce a sticky hdr-level ditto for FF_FLAGS_NO_IO_THRU_MDS in
struct nfs4_flexfile_layout::flags (NFS4_FF_HDR_NO_IO_THRU_MDS bit),
set whenever ff_layout_alloc_lseg() parses an lseg with the flag. The
bit is never cleared for the lifetime of the layout hdr; the server is
assumed to be consistent in its no-fallback policy per file.
kzalloc() in ff_layout_alloc_layout_hdr() zero-initializes the field.
Use the new ff_layout_hdr_no_fallback_to_mds() helper to gate
ff_layout_pg_get_mirror_count_write(): when pnfs_update_layout() returns
NULL (e.g. NFS_LAYOUT_BULK_RECALL, pnfs_layout_io_test_failed,
pnfs_layoutgets_blocked) the existing code unconditionally calls
nfs_pageio_reset_write_mds(). This is a source of unwanted WRITE to
MDS. Fix it by checking NFS4_FF_HDR_NO_IO_THRU_MDS bit, and if set
surface -EAGAIN instead; the writepage-side caller (nfs_do_writepage()
for buffered, nfs_direct_write_reschedule() for O_DIRECT) then
redirties the request so writeback retries via pNFS.
Fixes: 260074cd84 ("pNFS/flexfiles: Add support for FF_FLAGS_NO_IO_THRU_MDS")
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a375cafc1 ]
Commit f06bedfa62 ("pNFS/flexfiles: don't attempt pnfs on fatal DS
errors") teaches ff_layout_{read,write}_pagelist() to return
PNFS_NOT_ATTEMPTED when nfs4_ff_layout_prepare_ds() fails with a
nfs_error_is_fatal() errno (e.g. -ETIMEDOUT from a SOFTCONN connect
deadline, -ENOMEM, -ERESTARTSYS), so that the client gives up instead
of spinning. pnfs_do_{read,write}() then dispatches the I/O through
pnfs_{read,write}_through_mds() → nfs_pageio_reset_{read,write}_mds().
That fallback is unconditional and silently violates FF_FLAGS_NO_IO_THRU_MDS:
when the layout segment carries the flag (typically single-mirror
appliance layouts where MDS I/O is explicitly forbidden), the
out_failed: path's \`&& !ds_fatal_error\` clause overrides the flag's
short-circuit through ff_layout_avoid_mds_available_ds() and routes
the I/O to the MDS file handle anyway.
This is reachable in practice during a data-server restart: SOFTCONN
exhaustion produces -ETIMEDOUT, which is fatal per nfs_error_is_fatal(),
which triggers PNFS_NOT_ATTEMPTED, which silently goes to MDS.
Preserve the upstream "don't spin on fatal errors" intent for layouts
that permit MDS fallback. For layouts with FF_FLAGS_NO_IO_THRU_MDS
set, mark the layout for return and request PNFS_TRY_AGAIN instead;
if the server cannot supply a usable layout the failure now surfaces
cleanly via pnfs_update_layout(), rather than via silent MDS I/O that
contradicts the flag.
Fixes: f06bedfa62 ("pNFS/flexfiles: don't attempt pnfs on fatal DS errors")
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ff72e1cdf ]
When a read request is split into multiple subrequests, earlier
completions may advance PG_UPTODATE state for the page group once
their bytes fall within hdr->good_bytes. If a later subrequest in
the same group then completes with NFS_IOHDR_ERROR, the read path
needs to clear any accumulated PG_UPTODATE state and keep later
completions from rebuilding it.
Otherwise, a subsequent successful subrequest can re-enter
nfs_page_group_set_uptodate(), restore the page-group sync state,
and leave stale PG_UPTODATE behind for nfs_page_group_destroy()
to trip over in nfs_free_request().
Add a sticky page-group read-failed flag. Once any subrequest in
the group is known to be bad, mark the group failed, clear any
accumulated PG_UPTODATE state, and refuse further PG_UPTODATE
synchronization for the rest of the completion walk.
Fixes: 67d0338edd ("nfs: page group syncing in read path")
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77b160b2d8 ]
Sometimes unmounting an NFS filesystem mounted with pNFS SCSI
layouts triggers the following warning:
BUG: scheduling while atomic: umount.nfs4/...
__schedule_bug+0xbd/0x100
schedule_debug.constprop.0+0x19f/0x220
__schedule+0x10d/0x10a0
schedule+0x74/0x190
schedule_timeout+0xf5/0x220
io_schedule_timeout+0xd5/0x160
__wait_for_common+0x186/0x4b0
blk_execute_rq+0x2ef/0x3a0
scsi_execute_cmd+0x1ff/0x700
sd_pr_out_command.isra.0+0x242/0x380 [sd_mod]
bl_unregister_scsi.constprop.0+0x109/0x3c0 [blocklayoutdriver]
bl_unregister_dev+0x175/0x1c0 [blocklayoutdriver]
bl_free_device+0x1f/0x1b0 [blocklayoutdriver]
bl_free_deviceid_node+0x12/0x30 [blocklayoutdriver]
nfs4_put_deviceid_node+0x171/0x360 [nfsv4]
ext_tree_remove+0x11c/0x1d0 [blocklayoutdriver]
_pnfs_return_layout+0x416/0x900 [nfsv4]
nfs4_evict_inode+0x108/0x130 [nfsv4]
evict+0x316/0x750
dispose_list+0xf1/0x1a0
evict_inodes+0x33f/0x440
generic_shutdown_super+0xc9/0x4e0
kill_anon_super+0x3a/0x90
nfs_kill_super+0x44/0x60 [nfs]
deactivate_locked_super+0xb8/0x1b0
cleanup_mnt+0x25a/0x380
task_work_run+0x13e/0x210
exit_to_user_mode_loop+0x169/0x400
do_syscall_64+0x467/0x1550
entry_SYSCALL_64_after_hwframe+0x76/0x7e
The warning occurs because the block layout driver unregisters the SCSI
device while the inode lock is still held. Device unregistration issues
a SCSI PR command, which may sleep, resulting in a "scheduling while
atomic" warning.
During layout return, ext_tree_remove() invokes the layout driver's
return_range callback while holding the inode lock. For block layouts,
this callback eventually calls bl_unregister_scsi(), which may block in
scsi_execute_cmd() while issuing PR commands to the device.
Fix this by deferring the return_range callbacks until after the inode
lock has been released. The layout header reference count is incremented
before invoking return_range(), ensuring that the layout header remains
valid while the layout driver removes extents from the extent tree.
Fixes: c88953d87f ("pnfs: add return_range method")
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e786233d2e ]
rl_kref formerly served two distinct lifetimes through a single
refcount: it gated when a Reply could wake its RPC task, and it
gated when an rpcrdma_req could return to its free pool. The
marshal path took the Send-side reference only when SGEs needed
DMA-unmap (sc_unmap_count > 0), which made a Send carrying only
pre-registered buffers an exception: the Reply handler dropped
rl_kref from 1 to 0 and freed the req while the HCA might still
be DMA-reading from its send buffer.
Give rl_kref a narrower job. The RPC layer takes one reference
when slot allocation hands a req out. rpcrdma_prepare_send_sges()
takes a Send-side reference unconditionally after WR preparation
succeeds. xprt_rdma_free_slot() and xprt_rdma_bc_free_rqst() drop
the RPC-layer reference; rpcrdma_sendctx_unmap() drops the
Send-side reference. The req returns to its free pool only after
both owners have signed off.
The existing kref_init(&req->rl_kref) call in
rpcrdma_prepare_send_sges() is removed. Initialization moves to
the slot-allocation paths (xprt_rdma_alloc_slot and
rpcrdma_bc_rqst_get), and the release callback re-arms rl_kref
before the req returns to a free pool. A re-init in the marshal
path would discard the RPC-layer reference that already exists
on entry.
Three invariants follow:
- Any rpcrdma_req held by an rpc_rqst has rl_kref >= 1.
xprt_rdma_alloc_slot(), rpcrdma_bc_rqst_get(), and the
backlog-wake branch in xprt_rdma_alloc_slot() each kref_init
rl_kref before publishing the req. Without this invariant,
an RPC task that aborts between slot allocation and marshal
(gss_refresh failure or signal during call_connect, for
example) would drive xprt_release() ->
xprt_rdma_free_slot() -> kref_put against a refcount of
zero, saturating refcount_t and stranding the slot.
- The Send-side reference is taken only after WR prep
succeeds. A mapping failure in rpcrdma_prepare_send_sges()
runs rpcrdma_sendctx_cancel(), which DMA-unmaps the sendctx
and clears sc_req without touching rl_kref. The sendctx
ring walks in rpcrdma_sendctx_put_locked() and
rpcrdma_sendctxs_destroy() skip entries with sc_req == NULL,
so a burst of -EIO marshal failures cannot hold reqs off
rb_send_bufs.
- The release callback re-arms rl_kref so the next consumer
enters with the invariant satisfied.
Replies now complete the RPC directly. rpcrdma_reply_handler()
calls rpcrdma_complete_rqst() in place of kref_put on the
non-LocalInv branch. The LocalInv branch already completes the
RPC from frwr_unmap_async() and is unaffected.
Because Send-side references can now outlive RPC completion,
connection teardown drains sendctx entries whose unsignaled
Sends never had a later signaled completion to walk the ring.
rpcrdma_sendctxs_destroy() walks the active range and runs
rpcrdma_sendctx_unmap() on each entry with a non-NULL sc_req
before the request buffers are reset, and is moved ahead of
rpcrdma_reqs_reset() in rpcrdma_xprt_disconnect() so the reqs
are still in their pre-reset state when the Send-side refs are
released.
The drain creates a teardown-ordering hazard on the backchannel
path. With the new lifetime, releasing a bc_prealloc req from
rpcrdma_req_release() re-adds it to bc_pa_list. The disconnect
in xprt_rdma_destroy() runs after xprt_destroy_backchannel() has
already emptied bc_pa_list, so the drained reqs would otherwise
leak. xprt_rdma_destroy() now runs xprt_rdma_bc_destroy(xprt, 0)
a second time after the disconnect to reclaim them.
Fixes: 0ab1152370 ("xprtrdma: Wake RPCs directly in rpcrdma_wc_send path")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2797ae7c92 ]
Send signaling matters only when the prepared Send has page
mappings to unmap. Today that test is expressed indirectly with
rl_kref, because the Send-side reference is taken only for Sends
with mapped SGEs.
Split the SGE DMA unmap loop into its own helper and use
sc_unmap_count directly for the signaling decision. This keeps the
current behavior but removes one dependency on the old rl_kref
semantics before the request lifetime rules are changed.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Stable-dep-of: e786233d2e ("xprtrdma: Decouple req recycling from RPC completion")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 704f3f640f ]
rpcrdma_post_recvs() runs in CQ poll context and its cost
falls on the latency-critical path between polling a Receive
completion and waking the RPC consumer. Every cycle spent
refilling the Receive Queue delays delivery of the reply to
the NFS layer.
Move the rpcrdma_post_recvs() call in rpcrdma_reply_handler()
to after the RPC has been decoded and completed. The larger
batch size from the preceding patch provides sufficient
Receive Queue headroom to absorb the brief delay before
buffers are replenished.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Stable-dep-of: e786233d2e ("xprtrdma: Decouple req recycling from RPC completion")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 765bde47fe ]
xprt_rdma_alloc_slot() and xprt_rdma_free_slot() lack serialization
between the buffer pool and the backlog queue. A buffer freed
after rpcrdma_buffer_get() finds the pool empty but before
rpc_sleep_on() places the task on the backlog is returned to the
pool with no waiter to wake, leaving the task stuck on the backlog
indefinitely.
After joining the backlog, re-check the pool and route any
recovered buffer through xprt_wake_up_backlog(), whose queue lock
serializes with concurrent wakeups and avoids double-assignment
of slots.
Because xprt_rdma_free_slot() does not hold reserve_lock, the
XPRT_CONGESTED double-check in xprt_throttle_congested() is
ineffective: a task can join the backlog through that path after
free_slot has already found it empty and cleared the bit. Avoid
this by using xprt_add_backlog_noncongested(), which queues the
task without setting XPRT_CONGESTED, so every allocation reaches
xprt_rdma_alloc_slot() and its post-sleep re-check.
Fixes: edb41e61a5 ("xprtrdma: Make rpc_rqst part of rpcrdma_req")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Stable-dep-of: e786233d2e ("xprtrdma: Decouple req recycling from RPC completion")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 100142093e ]
Commit a721035477 ("SUNRPC/xprt: async tasks mustn't block waiting
for memory") changed xprt_rdma_alloc_slot() to set tk_status to
-ENOMEM so that call_reserveresult() would sleep HZ/4 before
retrying. That rationale applies to xprt_dynamic_alloc_slot(),
where an immediate retry under memory pressure wastes CPU, but not
to the RDMA backlog path: a task woken from the backlog has a slot
waiting for it, so the 250 ms rpc_delay adds latency without
benefit.
This also aligns the code with the existing kernel-doc for
xprt_rdma_alloc_slot(), which already documented %-EAGAIN.
Fixes: a721035477 ("SUNRPC/xprt: async tasks mustn't block waiting for memory")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Stable-dep-of: e786233d2e ("xprtrdma: Decouple req recycling from RPC completion")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e13dd9ea8 ]
The original code was designed so that most calls to
rpcrdma_rep_create() would occur on the NUMA node that the device
preferred. There are a few cases where that's not possible, so
those reps are marked as temporary.
However, we have the device (and its preferred node) already in
rpcrdma_rep_create(), so let's use that to guarantee the memory
is allocated from the correct node.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Stable-dep-of: e786233d2e ("xprtrdma: Decouple req recycling from RPC completion")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91668417d4 ]
A layout can still be striped with num_fh = 1 as it is perfectly possible
that both MDS and DSs can handle the same filehandle. Hence check according
to stripe_count > 1, which is the correct check to begin with.
We should not be called with flseg->dsaddr = NULL, but if for some reason
we do, return our best guess with is flseg->num_fh > 1.
Fixes: a6b9d2fa00 ("pNFS/filelayout: Fix coalescing test for single DS")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Anna Schumaker <anna.schumaker@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68018df3f5 ]
In kallsyms__parse(), the loop reading symbol names iterates with i <
sizeof(symbol_name), which allows i to reach sizeof(symbol_name) upon
loop exit. The subsequent symbol_name[i] = '\0' then writes one byte
past the end of the stack-allocated symbol_name[] array.
Fix this by changing the loop bound to KSYM_NAME_LEN, so the null
terminator always lands within the array. The overflow is triggerable by
a kallsyms entry with a symbol name of KSYM_NAME_LEN+1 or more
characters (e.g., long Rust mangled names or a malicious
/proc/kallsyms).
Fixes: 53df2b9344 ("libsymbols kallsyms: Parse using io api")
Signed-off-by: Rui Qi <qirui.001@bytedance.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d52d42e2e5 ]
There are multi spba-busses for i.MX8M* platforms, if only search for
the first spba-bus in DT, the found spba-bus may not the real bus of
audio devices, which cause issue for sdma p2p case, as the sdma p2p
script presently does not deal with the transactions involving two devices
connected to the AIPS bus.
Search the SDMA parent node first, which should be the AIPS bus, then
search the child node whose compatible string is spba-bus under that AIPS
bus for the above multi spba-busses case.
Fixes: 8391ecf465 ("dmaengine: imx-sdma: Add device to device support")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260407032755.2758049-1-shengjiu.wang@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4c6ec729f ]
Add descriptions for the missing parameters for ALLMEnabled and
ALLMValue to keep the function documentation synchronized with the
function prototype mod_build_hf_vsif_infopacket().
Fixes the below with gcc W=1:
../display/modules/info_packet/info_packet.c:507 function parameter 'ALLMEnabled' not described in 'mod_build_hf_vsif_infopacket'
../display/modules/info_packet/info_packet.c:507 function parameter 'ALLMValue' not described in 'mod_build_hf_vsif_infopacket'
Fixes: 3c2381b92c ("drm/amd/display: add support for VSIP info packet")
Cc: Roman Li <roman.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7a9125cac ]
On 64K page-size kernels, mounting NTFS volumes smaller than ~650 MB
fails with EINVAL. The issue is in log_replay(): the initial log page
size probe uses PAGE_SIZE (65536) instead of DefaultLogPageSize (4096)
when PAGE_SIZE exceeds DefaultLogPageSize * 2.
This makes norm_file_page() require the $LogFile to be at least
50 * 65536 = 3.2 MB, but mkfs.ntfs creates a $LogFile of only ~1.5 MB
for a typical 300 MB volume. norm_file_page() returns 0 and the mount
is rejected with EINVAL.
On 4K kernels the #if guard evaluates to true, so use_default=true is
passed and DefaultLogPageSize (4096) is used, requiring only ~200 KB.
This path works fine.
Fix this by always passing use_default=true, which forces the initial
probe to use DefaultLogPageSize regardless of the kernel's PAGE_SIZE.
This is safe because, after reading the on-disk restart area, log_replay()
already re-adjusts log->page_size to match the volume's actual
sys_page_size.
Also fix read_log_page() to pass log->page_size instead of PAGE_SIZE to
ntfs_fix_post_read(), matching the actual buffer size.
Fixes: b46acd6a6a ("fs/ntfs3: Add NTFS journal")
Tested-by: Matthew R. Ochs <mochs@nvidia.com>
Signed-off-by: Jamie Nguyen <jamien@nvidia.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb11485a87 ]
run_get_highest_vcn() parses a packed NTFS mapping-pairs buffer without
any length bound, relying solely on a 0x00 terminator to stop. A
crafted $LogFile UpdateMappingPairs record whose embedded attribute
contains mapping-pairs runs without a terminator causes the function to
read past the slab allocation, triggering a KASAN slab-out-of-bounds
read on mount.
The sibling function run_unpack() received an analogous bounds-check in
commit b62567bca4 ("ntfs3: add buffer boundary checks to run_unpack()"),
but run_get_highest_vcn() was missed.
Take a run_buf_size parameter and reject any run header whose payload
would extend past the buffer end, mirroring the pattern used by
run_unpack(). The caller in fslog.c passes the remaining attribute
bytes after the mapping-pairs offset.
KASAN report (on mainline v7.1 merge window HEAD):
BUG: KASAN: slab-out-of-bounds in run_get_highest_vcn+0x3c0/0x410
Read of size 1 at addr ffff88800e2d5400 by task mount/72
Call Trace:
run_get_highest_vcn+0x3c0/0x410
do_action.isra.0+0x3ba8/0x7b50
log_replay+0x9ddd/0x10200
ntfs_loadlog_and_replay+0x4ad/0x610
ntfs_fill_super+0x214a/0x4540
Fixes: b62567bca4 ("ntfs3: add buffer boundary checks to run_unpack()")
Signed-off-by: Jaeyeong Lee <lee@jaeyeong.cc>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f22a5db8a7 ]
The @dev member described in the kernel-doc does not exist in the
struct. Remove the stale entry.
Fixes: 0610430e3d ("HID: logitech-hidpp: add input_device ptr to struct hidpp_device")
Assisted-by: opencode:big-pickle
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22fa1c39ba ]
pmc_register_ops() gets an owned reference to the
"atmel,sama5d2-securam" node with of_find_compatible_node(). The
success path dropped that reference before passing the node to
of_iomap(), leaving of_iomap() to consume a node pointer after the caller
had released its reference.
Move of_node_put() after of_iomap() so the node remains referenced for
the mapping operation. The unavailable-node error path already releases
the reference.
Fixes: 4d21be8640 ("clk: at91: pmc: execute suspend/resume only for backup mode")
Signed-off-by: Yuho Choi <dbgh9129@gmail.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://patch.msgid.link/20260529042051.1626978-1-dbgh9129@gmail.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b39f3bb9f5 ]
If tcs3472_probe() fails after enabling the chip (by writing PON | AEN
to the ENABLE register), the error paths return without powering down
the device.
Add an 'error_powerdown' label at the end of the cleanup chain that
calls tcs3472_powerdown() to power down the chip. The existing label
cascade is rerouted to fall through to the new label.
Move tcs3472_powerdown() above tcs3472_probe() so the probe can call
it without a forward declaration.
Found by code inspection while reviewing the probe error paths in
preparation for the devm_ conversion.
Fixes: eb869ade30 ("iio: Add tcs3472 color light sensor driver")
Signed-off-by: Aldo Conte <aldocontelk@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bdff291d2 ]
Currently, If i2c_smbus_read_i2c_block_data() fails but
mma8452_set_runtime_pm_state() succeeds, mma8452_read() returns 0.
As a result, the caller mma8452_read_raw() assumes the read was
successful and proceeds to use a buffer containing uninitialized
stack memory.
Add proper checking of the I2C read return value and propagate errors
to the caller.
Fixes: 96c0cb2bbf ("iio: mma8452: add support for runtime power management")
Signed-off-by: Sanjay Chitroda <sanjayembeddedse@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 947eb6f0a2 ]
ams_event_to_channel() may return a pointer past the end of
dev->channels when no matching scan_index is found. This can lead
to invalid memory access in ams_handle_event().
Add a bounds check in ams_event_to_channel() and return NULL when
no channel is found. Also guard the caller to safely handle this
case.
Fixes: d5c70627a7 ("iio: adc: Add Xilinx AMS driver")
Signed-off-by: Guilherme Ivo Bozi <guilherme.bozi@usp.br>
Reviewed-by: Salih Erim <salih.erim@amd.com>
Tested-by: Salih Erim <salih.erim@amd.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9a00d727b ]
Currently in the AK8975 driver there are four instances where potential
uninitialized kernel stack memory leaks can occur. If
i2c_smbus_read_i2c_block_data_or_emulated() returns a value less than
the size of the buffer, uninitialized bytes are retained in the buffer
and later the buffer is passed on to IIO buffers, potentially leaking
memory to userspace.
Fix this by adding checks whether the return value of the function is
equal to the size of the buffer and subsequently if the value is
lesser than zero to distinguish from a returned error code.
Fixes: bc11ca4a0b ("iio:magnetometer:ak8975: triggered buffer support")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/patchset/20260513-ak8975-fix-v1-1-104ea605dd54%40gmail.com
Signed-off-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c50a95ceb ]
Sashiko reported a bug where the si1133_command exits on timeout
without halting the sensor or masking the interrupt. If the sensor
completes the command later, any subsequent command to the sensor
will cause the IRQ handler to complete immediately, returning stale
data to the driver all while the command hasn't finished yet, shifting
all potential reads in the future.
Fix this by masking the IRQ if wait_for_completion_timeout() fails.
When initiating a new command, do a dummy read of the IRQ_STATUS
register and turn the IRQ back on.
Fixes: e01e7eaf37 ("iio: light: introduce si1133")
Reported-by: sashiko-bot <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/message/20260428-si1133-checkup-v2-5-70ad14bfefe2%40gmail.com
Assisted-by: gemini:gemini-3.1-pro-preview
Signed-off-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a5f45ed23 ]
Sashiko reported a potential race condition happening when the driver
returns an errno after a timeout in the si1133_command() function. The
premature exit causes the hardware and software counters to become out
of sync by not updating data->rsp_seq, therefore the internal hardware
counter keeps incrementing.
Fix this by adding a call to si1133_cmd_reset_counter() before returning
from timeout.
Fixes: e01e7eaf37 ("iio: light: introduce si1133")
Reported-by: sashiko-bot <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/message/20260428-si1133-checkup-v2-5-70ad14bfefe2%40gmail.com
Assisted-by: gemini:gemini-3.1-pro-preview
Signed-off-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbf003b779 ]
This patch improves the module cleanup process in the tlclk driver to
prevent potential use-after-free and race conditions.
Currently, the file_operations structure does not specify the .owner
field, which could allow the module to be unloaded while user-space
processes are still interacting with the device. Additionally, the
tlclk_cleanup() function frees the alarm_events memory before ensuring
that blocked processes in the waitqueue are fully awakened and that the
switchover_timer has completed.
To address these cases, this patch:
- Sets '.owner = THIS_MODULE' in tlclk_fops to safely defer module
unloading while the device is in use.
- Updates tlclk_cleanup() to explicitly wake up all blocked readers
(wake_up_all), properly release hardware I/O regions, and safely
delete the timer (timer_delete_sync) prior to freeing memory.
Fixes: 1a80ba8827 ("[PATCH] Telecom Clock Driver for MPCBL0010 ATCA computer blade")
Signed-off-by: James Kim <james010kim@gmail.com>
Link: https://patch.msgid.link/20260503101131.64219-1-james010kim@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11b5c101e2 ]
The `max3421_hub_control()` function handles USB hub class requests
to the virtual root hub. The `GetPortStatus` case correctly rejects
requests with `index != 1`, since the virtual root hub has only a
single port. However, the `ClearPortFeature` and `SetPortFeature`
cases lack the same check.
Fix this by extending the `index != 1` rejection to both cases,
matching the existing behavior of `GetPortStatus`.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Seungjin Bae <eeodqql09@gmail.com>
Link: https://patch.msgid.link/20260518224901.1887013-3-eeodqql09@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cff06b03b5 ]
The `max3421_hub_control()` function handles USB hub class requests
to the virtual root hub. In the `default` branches of both the
`ClearPortFeature` and `SetPortFeature` switch statements, it modifies
`max3421_hcd->port_status` by left shifting 1 by the request's `value`
parameter. However, it does not validate whether this shift will exceed
the width of `port_status`.
So if a malicious userspace task with access to the root hub via
/dev/bus/usb/.../001 issues a USBDEVFS_CONTROL ioctl with `wValue`
greater than or equal to 32, the left shift operation invokes
shift-out-of-bounds undefined behavior. This results in arbitrary
bit corruption of `port_status`, including the normally-immutable
change bits, which can bypass internal state checks and confuse the
hub status.
Fix this by rejecting requests whose `value` exceeds the shift width
before performing the shift.
This issue was found using a KLEE-based symbolic execution tool for
kernel drivers that I'm currently developing.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Signed-off-by: Seungjin Bae <eeodqql09@gmail.com>
Link: https://patch.msgid.link/20260518224901.1887013-1-eeodqql09@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cb1c5b32a ]
comp_register_videodev() allocates a video_device with
video_device_alloc() and releases it if video_register_device() fails.
This can double free the video_device when __video_register_device()
reaches device_register() and that call fails:
video_register_device()
-> __video_register_device()
-> device_register() fails
-> put_device(&vdev->dev)
-> v4l2_device_release()
-> vdev->release(vdev)
-> video_device_release(vdev)
comp_register_videodev()
-> video_device_release(mdev->vdev)
Use video_device_release_empty() while registering the device so that
registration failure paths do not free mdev->vdev through vdev->release().
comp_register_videodev() then releases mdev->vdev exactly once on failure.
Restore video_device_release() after successful registration so the
registered device keeps its normal lifetime handling.
This issue was found by a static analysis tool I am developing.
Fixes: eab231c039 ("staging: most: v4l2-aim: remove unnecessary label err_vbi_dev")
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Link: https://patch.msgid.link/20260517111218.945796-1-lgs201920130244@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b57d1a40bc ]
When the SOF audio driver fails to initialize (e.g. firmware boot
timeout), its devres unwind frees the snd_sof_dev object that the
mailbox client (mtk-adsp-ipc) reaches via chan->cl->rx_callback.
The mtk-adsp-mailbox shutdown clears the mailbox command registers
but leaves the IRQ line unmasked, so a late interrupt can still
queue a threaded handler after mbox_free_channel() had cleared
chan->cl, and mbox_chan_received_data() would then trigger UAF:
BUG: KASAN: slab-use-after-free in sof_ipc3_validate_fw_version
sof_ipc3_validate_fw_version
sof_ipc3_do_rx_work
sof_ipc3_rx_msg
mt8196_dsp_handle_request
mtk_adsp_ipc_recv
mbox_chan_received_data
mtk_adsp_mbox_isr
irq_thread_fn
Freed by task ...:
kfree
devres_release_all
really_probe
... (sof-audio-of-mt8196 probe failure)
The crash was observed roughly three seconds after the failed probe.
disable_irq() in shutdown and enable_irq() in startup. disable_irq()
also waits for any in-flight interrupts, so by the time
mbox_free_channel() proceeds to clear chan->cl no rx_callback can run.
In addition, request the IRQ with IRQF_NO_AUTOEN so it stays masked
between probe and the first client bind — otherwise an early interrupt
can crash on chan->cl == NULL in mbox_chan_received_data().
Fixes: af2dfa96c5 ("mailbox: mediatek: add support for adsp mailbox controller")
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebee9004cc ]
Every platform driver can be forced to match a device that doesn't
match its list of device IDs because of device_match_driver_override()
so platform drivers that rely on the existence of a device's driver
data need to verify its presence.
Accordingly, add requisite match and driver data checks against NULL
to the driver where they are missing.
Fixes: a4a86d273f ("phy: phy-can-transceiver: Add support for generic CAN transceiver driver")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260513220336.369628-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dece4435d ]
There is a potential deadlock scenario in mhi_ep_reset_worker() where
the state_lock mutex is acquired twice in the same call chain:
mhi_ep_reset_worker()
mutex_lock(&mhi_cntrl->state_lock)
mhi_ep_power_up()
mhi_ep_set_ready_state()
mutex_lock(&mhi_cntrl->state_lock) <- Deadlock
Fix this by releasing the state_lock before calling mhi_ep_power_up().
The lock is only needed to protect current MHI state read operation. The
lock can be safely released before proceeding with the power up sequence.
Fixes: 7a97b6b473 ("bus: mhi: ep: Add support for handling MHI_RESET")
Signed-off-by: Sumit Kumar <sumit.kumar@oss.qualcomm.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Link: https://patch.msgid.link/20260414-reset_worker_deadlock-v2-1-42fd682b45db@oss.qualcomm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2fc2c6ebb ]
The device_set_wakeup_enable() call in ebook_switch_add() doesn't
actually do anything because power.can_wakeup is not set for ACPI
device objects. Moreover, had it done anything, it would have
registered a wakeup source object that wouldn't have been used
going forward and that wakeup source would have been leaked after
driver removal because ebook_switch_remove() doesn't clean it up.
Accordingly, remove that call from ebook_switch_add().
Also prevent leaking an enabled ACPI GPE after removing the driver by
adding appropriate cleanup code to ebook_switch_remove().
Fixes: 89ca11771a ("OLPC XO-1.5 ebook switch driver")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/1966125.tdWV9SEqCh@rafael.j.wysocki
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Arnaldo Carvalho de Melo
Chuck Lever
Chris Mason
Lad Prabhakar
Jamie Nguyen
Shuvam Pandey
Li RongQing
Mike Snitzer
Clark Wang
Dai Ngo
Sagi Grimberg
Phillip Varney
Nuno Sá
Icenowy Zheng
Rui Qi
Shengjiu Wang
Srinivasan Shanmugam
Konstantin Komarov
Rosen Penev
Yuho Choi
Aldo Conte
Sanjay Chitroda
Guilherme Ivo Bozi
Joshua Crofts
James Kim
Seungjin Bae
Guangshuo Li
Sergey Senozhatsky
Andy Shevchenko
Sumit Kumar
Rong Zhang
Rafael J. Wysocki